Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2014.11–2016.05
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301870 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a lane departure warning camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the lane departure warning camera may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 85292B 1.REMOVE FRONT WIPER ARM HEAD CAP

Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 55810F 4.REMOVE FRONT VENTILATOR ASSEMBLY

Hide 55781E 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 86468 6.REMOVE LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)

Hide 7.DISCONNECT ROOF HEADLINING ASSEMBLY

Hide 87810 8.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87818 9.REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)

Hide 87810 10.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 56111 11.REMOVE WINDSHIELD GLASS (for Standard Roof)

a.
B274410E01
1.642,0.887 1.800,1.036 0.157,0.149 10 *1 1.734,0.869 1.79,0.447 false

Apply protective tape to the installation position of the windshield glass on the vehicle body.

Text in Illustration
*1 Protective Tape

HINT:

Apply protective tape to the installation surface to prevent it from being scratched.



b.
B291620E01
1.375,0.787 1.532,0.935 0.157,0.149 10 *1 1.661,0.424 1.459,0.424 1.459,0.424 1.459,0.779 false 1.661,0.685 1.459,0.685 false

Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

Text in Illustration
*1 Matchmark

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.



c.
B274413E01
1.164,1.27 1.452,1.421 0.288,0.152 10 *1 0.879,1.291 1.136,1.349 false

Pass a piano wire between the vehicle body and windshield glass from the interior as shown in the illustration.

Text in Illustration
*1 Piano Wire


d.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


e.

Cut off the adhesive applied to the bottom of the windshield glass by pulling the piano wire under the glass.

NOTICE:
·

When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.




f.

While pushing back the lip of the molding with a screwdriver, pass a piano wire between the vehicle body and windshield glass so that both wire ends are in the interior as shown in the illustration.

B274414E01
0.244,2.26 0.403,2.404 0.159,0.144 10 *1 1.026,2.716 1.179,2.855 0.153,0.138 10 *2 0.769,1.755 0.927,1.899 0.159,0.144 10 *a 2.506,1.126 2.661,1.263 0.155,0.137 10 *3 3.081,1.067 3.231,1.209 0.150,0.142 10 *2 3.507,0.879 3.666,1.023 0.159,0.144 10 *1 3.909,1.107 4.063,1.247 0.154,0.140 10 *4 4.306,1.12 4.456,1.265 0.150,0.145 10 *3 3.988,1.101 4.038,0.91 false 3.147,1.058 3.147,0.843 false 3.57,0.871 3.478,0.714 false 0.755,1.826 0.524,2.052 false 0.394,2.326 0.596,2.326 false 1.095,2.708 1.095,2.337 false 4.013,0.191 4.217,0.359 0.204,0.168 10 *B 2.505,0.191 2.708,0.365 0.204,0.174 10 *A 3.233,2.977 3.390,3.119 0.156,0.142 10 *1 3.22,3.044 2.869,3.044 false 2.651,1.188 2.799,1.122 false 4.646,1.048 4.796,1.190 0.150,0.142 10 *2 5.029,0.863 5.188,1.007 0.159,0.144 10 *1 4.708,1.044 4.666,0.828 false 5.104,0.863 4.998,0.692 false 4.372,1.107 4.372,0.98 false

Text in Illustration
*A 1-piece Type *B 2-piece Type
*1 Piano Wire *2 Adhesive
*3 No. 1 Stopper *4 No. 2 Stopper
*a Lip of the molding - -


g.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


h.

Cut off the adhesive by pulling the piano wire around the windshield glass.

NOTICE:
·

When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.

·

When passing the piano wire below the 2 stoppers, make sure to cut the adhesive applied between the windshield glass and stoppers.

·

Be careful not to drop the windshield glass.




i.

Disconnect the windshield glass stoppers.

B291618E01
1.71,1.692 1.869,1.836 0.159,0.144 10 *1 4.229,0.55 4.432,0.717 0.204,0.168 10 *B 0.85,0.55 1.054,0.723 0.204,0.174 10 *A 4.719,1.477 4.868,1.619 0.150,0.142 10 *2 5.007,1.483 5.166,1.627 0.159,0.144 10 *1 4.793,1.472 4.849,1.239 false 1.783,1.5 1.783,1.688 false 5.078,1.32 5.078,1.478 false

Text in Illustration
*A 1-piece Type *B 2-piece Type
*1 No. 1 Stopper *2 No. 2 Stopper

NOTICE:
·

There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.

·

When removing the windshield glass, do not replace the windshield outside moulding with a repair moulding. Make sure to use a new one.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.



j.

Using suction cups, remove the windshield glass.

NOTICE:
·

Be careful not to drop the windshield glass.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass.




k.

Remove the parts of the 2 No. 1 windshield glass stoppers (1-piece type) or 2 No. 2 windshield glass stoppers (2-piece type) that remain on the vehicle.


Hide 56111 12.REMOVE WINDSHIELD GLASS (for Glass Roof)

a.
B274411E01
1.832,0.688 1.990,0.832 0.159,0.144 10 *1 1.925,0.685 1.988,0.451 false

Apply protective tape to the installation position of the windshield glass on the vehicle body.

Text in Illustration
*1 Protective Tape

HINT:

Apply protective tape to the installation surface to prevent it from being scratched.



b.
B274433E01
2.107,0.145 2.266,0.289 0.159,0.144 10 *a 2.09,0.232 1.915,0.285 false

Cut the windshield outside sub moulding as shown in the illustration.

Text in Illustration
*a Cut


c.
B291620E01
1.375,0.787 1.532,0.935 0.157,0.149 10 *1 1.661,0.424 1.459,0.424 1.459,0.424 1.459,0.779 false 1.661,0.685 1.459,0.685 false

Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

Text in Illustration
*1 Matchmark

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.



d.
B274413E01
1.164,1.27 1.452,1.421 0.288,0.152 10 *1 0.879,1.291 1.136,1.349 false

Pass a piano wire between the vehicle body and windshield glass from the interior as shown in the illustration.

Text in Illustration
*1 Piano Wire


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


f.

Cut off the adhesive applied to the bottom of the windshield glass by pulling the piano wire under the glass.

NOTICE:
·

When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.




g.

While pushing back the lip of the molding with a screwdriver, pass a piano wire between the vehicle body and windshield glass so that both wire ends are in the interior as shown in the illustration.

B274415E01
0.244,2.26 0.403,2.404 0.159,0.144 10 *1 1.026,2.716 1.179,2.855 0.153,0.138 10 *2 0.769,1.755 0.927,1.899 0.159,0.144 10 *a 2.506,1.126 2.661,1.263 0.155,0.137 10 *3 2.963,1.09 3.113,1.231 0.150,0.142 10 *2 3.515,0.871 3.673,1.015 0.159,0.144 10 *1 3.926,1.115 4.081,1.255 0.154,0.140 10 *4 4.264,1.12 4.414,1.265 0.150,0.145 10 *3 4.005,1.109 4.056,0.919 false 3.029,1.081 3.029,0.865 false 3.565,0.86 3.473,0.702 false 0.755,1.826 0.524,2.052 false 0.394,2.326 0.596,2.326 false 1.095,2.708 1.095,2.337 false 4.013,0.191 4.217,0.359 0.204,0.168 10 *B 2.505,0.191 2.708,0.365 0.204,0.174 10 *A 3.233,2.977 3.390,3.119 0.156,0.142 10 *1 3.22,3.044 2.869,3.044 false 2.651,1.188 2.804,1.117 false 4.571,1.076 4.721,1.218 0.150,0.142 10 *2 5.029,0.863 5.188,1.007 0.159,0.144 10 *1 4.632,1.072 4.59,0.856 false 5.104,0.863 4.998,0.692 false 4.33,1.107 4.33,0.98 false

Text in Illustration
*A 1-piece Type *B 2-piece Type
*1 Piano Wire *2 Adhesive
*3 No. 1 Stopper *4 No. 2 Stopper
*a Lip of the molding - -


h.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


i.

Cut off the adhesive by pulling the piano wire around the windshield glass.

NOTICE:
·

When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.

·

When passing the piano wire below the 2 stoppers, make sure to cut the adhesive applied between the windshield glass and stoppers.

·

Be careful not to drop the windshield glass.




j.

Disconnect the windshield glass stoppers.

B291619E01
1.661,1.732 1.820,1.876 0.159,0.144 10 *1 4.229,0.55 4.432,0.717 0.204,0.168 10 *B 0.85,0.55 1.054,0.723 0.204,0.174 10 *A 4.676,1.515 4.825,1.657 0.150,0.142 10 *2 4.964,1.524 5.123,1.668 0.159,0.144 10 *1 4.75,1.51 4.806,1.277 false 1.734,1.541 1.734,1.728 false 5.035,1.361 5.035,1.519 false

Text in Illustration
*A 1-piece Type *B 2-piece Type
*1 No. 1 Stopper *2 No. 2 Stopper

NOTICE:
·

There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.

·

When removing the windshield glass, do not replace the windshield outside moulding with a repair moulding. Make sure to use a new one.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.



k.

Using suction cups, remove the windshield glass.

NOTICE:
·

Be careful not to drop the windshield glass.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass.




l.

Remove the parts of the 2 No. 1 windshield glass stoppers (1-piece type) or 2 No. 2 windshield glass stoppers (2-piece type) that remain on the vehicle.


Hide 56117A 13.REMOVE WINDOW GLASS ADHESIVE DAM

a.
B274417E01
0.135,0.086 0.307,0.259 0.171,0.173 10 *A

Using a scraper, remove the windshield glass adhesive dam.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new one.




Hide 75533G 14.REMOVE WINDSHIELD OUTSIDE MOULDING (for Standard Roof)

a.
B274418E01
0.135,0.086 0.307,0.259 0.171,0.173 10 *A

Using a scraper, remove the windshield outside moulding.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.




Hide 75549A 15.REMOVE WINDSHIELD OUTSIDE SUB MOULDING (for Glass Roof)

a.
B274419E01
0.135,0.086 0.307,0.259 0.171,0.173 10 *A

Using a scraper, remove the windshield outside sub moulding.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside sub moulding with a new one.




Hide 75534 16.REMOVE WINDSHIELD OUTSIDE MOULDING LH (for Glass Roof)

a.
B318791E01
0.127,0.077 0.298,0.250 0.171,0.173 10 *A

Using a scraper, remove the windshield outside moulding LH.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding LH with a new one.




Hide 75533 17.REMOVE WINDSHIELD OUTSIDE MOULDING RH (for Glass Roof)

HINT:

Use the same procedure as for the LH side.


Hide 56115A 18.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.
B274422E01
0.135,0.086 0.307,0.259 0.171,0.173 10 *A

Using a scraper, remove the 2 No. 1 windshield glass stoppers.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 1 windshield glass stoppers with new ones.




Hide 56116C 19.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B274422E01
0.135,0.086 0.307,0.259 0.171,0.173 10 *A

Using a scraper, remove the 2 No. 2 windshield glass stoppers.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.




Hide 56115A 20.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B284937

Remove the 2 No. 1 windshield glass stoppers.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 56111 21.CLEAN WINDSHIELD GLASS

a.

Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



b.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.




Hide 22.CLEAN VEHICLE BODY

a.
B149737E07
2.311,1.537 2.44,1.663 false 0.934,1.646 1.160,1.799 0.226,0.152 10 *1 0.867,1.52 0.997,1.646 false 0.96,0.674 0.839,0.488 0.839,0.488 0.637,0.488 false 2.533,0.673 2.604,0.743 2.604,0.743 2.744,0.743 false 2.433,1.715 2.660,1.867 0.226,0.152 10 *1 0.417,0.419 0.643,0.572 0.226,0.152 10 *2 2.801,0.69 3.027,0.842 0.226,0.152 10 *2

Clean and shape the contact surfaces of the vehicle body.

Text in Illustration
*1 Adhesive
*2 Body

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.