Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301872 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 68294A 1.INSTALL BACK DOOR GLASS ADHESIVE DAM

a.
B274197E01
1.579,1.693 1.689,1.856 0.111,0.163 10 a

Cut the back door glass adhesive dam as shown in the illustration.

Standard Dimension:
Area Dimension
a 978 to 988 mm (3.21 to 3.24 ft.)



b.

Apply glass primer to the installation part of a new back door glass adhesive dam.

HINT:

If glass primer is applied to an area that is not specified, wipe off the glass primer with a non-residue solvent before it dries.



c.
B274730E02
0.865,0.813 1.094,1 false 2.594,0.813 2.354,1 false 1.292,2 1.406,2.146 0.115,0.146 10 true A 1.292,1.479 1.406,1.625 0.115,0.146 10 false A 0.5,3.198 0.844,3.344 0.344,0.146 10 false A - A 1.104,0.917 1.26,1.063 0.156,0.146 10 false *1 0.948,3.979 1.052,4.125 0.104,0.146 10 false a 2.177,0.917 2.333,1.063 0.156,0.146 10 false *1 0.177,0.167 0.396,0.313 0.219,0.146 10 false *A

Install a new back door glass adhesive dam onto the back door glass as shown in the illustration.

Text in Illustration
*A Back Side
*1 Ceramic Notch

Standard Dimension:
Area Dimension
a 6.7 mm (0.264 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.




Hide 75575D 2.INSTALL BACK WINDOW LOWER MOULDING

a.

Apply glass primer to the installation part of a new back window lower moulding.

HINT:

If glass primer is applied to an area that is not specified, wipe off the glass primer with a non-residue solvent before it dries.



b.
B274731E02
0.427,2.354 0.646,2.25 false 3.021,2.354 2.802,2.25 false 0.656,2.156 0.813,2.302 0.156,0.146 10 false *1 1.25,2.76 1.354,2.906 0.104,0.146 10 false a 1.292,1.229 1.406,1.375 0.115,0.146 10 true A 1.292,1.625 1.406,1.771 0.115,0.146 10 false A 1.198,2.042 1.531,2.188 0.333,0.146 10 false A - A 2.625,2.167 2.781,2.313 0.156,0.146 10 false *1 0.177,0.167 0.396,0.313 0.219,0.146 10 false *A

Install a new back window lower moulding onto the back door glass as shown in the illustration.

Text in Illustration
*A Back Side
*1 Ceramic Notch

Standard Dimension:
Area Dimension
a 0 to 3.0 mm (0 to 0.118 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.




Hide 75573G 3.INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING RH

a.

Apply glass primer to the installation part of a new No. 1 back window outside moulding RH.

HINT:

If glass primer is applied to an area that is not specified, wipe off the glass primer with a non-residue solvent before it dries.



b.
B274732E01
0.621,1.491 0.778,1.640 0.157,0.149 10 *1 1.206,3.017 1.307,3.166 0.102,0.149 10 a 1.574,0.622 1.689,0.771 0.116,0.149 10 A 1.964,0.732 2.079,0.881 0.116,0.149 10 A 0.712,2.131 1.047,2.280 0.335,0.149 10 A - A 0.482,1.45 0.607,1.575 false 0.18,0.165 0.376,0.332 0.196,0.168 10 *A

Install a new No. 1 back window outside moulding RH onto the back door glass as shown in the illustration.

Text in Illustration
*A Back Side
*1 Marking for Moulding

Standard Dimension:
Area Dimension
a 5.5 to 8.5 mm (0.217 to 0.335 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.




Hide 75574C 4.INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING LH

HINT:

Use the same procedure as for the RH side.


Hide 64818C 5.INSTALL NO. 1 BACK WINDOW GLASS SPACER

a.

Apply glass primer to the installation part of the No. 1 back window glass spacer.

HINT:

If glass primer is applied to an area that is not specified, wipe off the glass primer with a non-residue solvent before it dries.



b.
B274734E01
1.328,0.841 1.328,0.68 1.328,0.68 1.829,0.68 false 1.692,0.823 1.692,0.68 false 1.327,1.251 1.327,1.346 1.327,1.346 1.83,1.346 false 1.692,1.263 1.692,1.346 false 1.847,0.605 2.009,0.752 0.161,0.147 10 *1 1.845,1.259 2.006,1.406 0.161,0.147 10 *1 0.095,0.082 0.292,0.251 0.198,0.170 10 *A

Install a new No. 1 back window glass spacer onto the back door glass as shown in the illustration.

Text in Illustration
*A Back Side
*1 Marking for Spacer

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.




Hide 64819 6.INSTALL NO. 2 BACK WINDOW GLASS SPACER

a.

Apply glass primer to the installation part of the No. 2 back window glass spacer.

HINT:

If glass primer is applied to an area that is not specified, wipe off the glass primer with a non-residue solvent before it dries.



b.
B274733E01
0.18,0.172 0.406,0.343 0.226,0.171 10 *A 1.31,0.644 1.466,0.788 0.157,0.143 10 *1 2.124,0.845 2.124,0.72 2.124,0.72 1.489,0.72 false 1.76,0.827 1.76,0.72 false 2.125,1.255 2.125,1.346 2.125,1.346 1.611,1.346 false 1.76,1.267 1.76,1.346 false 1.436,1.269 1.592,1.413 0.157,0.143 10 *1

Install a new No. 2 back window glass spacer onto the back door glass as shown in the illustration.

Text in Illustration
*A Back Side
*1 Marking for Spacer

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.




Hide 68131 7.INSTALL BACK DOOR GLASS

a.

Using a brush, coat the installation surface of the vehicle body with body primer.

B283216E02
2.542,4.292 2.49,4.479 false 2.031,2.635 2.396,2.552 false 4.656,1.365 4.469,1.333 false 5.031,1.75 4.958,1.958 false 5.833,0.979 5.885,0.781 false 6.385,1.51 6.635,1.51 false 4.635,3.344 4.865,3.198 false 3.948,3.146 4.104,3.344 false 6.198,3.458 6.5,3.458 false 2.406,2.49 2.563,2.635 0.156,0.146 10 false *2 2.427,4.49 2.583,4.635 0.156,0.146 10 false *3 6.51,3.396 6.667,3.542 0.156,0.146 10 false *4 0.313,4.573 0.469,4.719 0.156,0.146 10 false *1 2.229,3.448 2.385,3.594 0.156,0.146 10 false *b 0.74,3.448 0.896,3.594 0.156,0.146 10 false *a 3.26,0.469 3.375,0.615 0.115,0.146 10 false B 3.26,0.813 3.375,0.958 0.115,0.146 10 false B 2.708,1.208 2.833,1.354 0.125,0.146 10 false C 2.104,1.969 2.229,2.115 0.125,0.146 10 true D 2.135,1.302 2.26,1.448 0.125,0.146 10 false D 2.125,0.802 2.24,0.948 0.115,0.146 10 false A 2.125,0.135 2.24,0.281 0.115,0.146 10 false A 3.792,3.073 3.948,3.219 0.156,0.146 10 false *4 4.885,3.125 5.042,3.271 0.156,0.146 10 false *4 4.313,1.271 4.469,1.417 0.156,0.146 10 false *4 4.885,1.969 5.042,2.115 0.156,0.146 10 false *4 5.896,0.708 6.052,0.854 0.156,0.146 10 false *4 6.646,1.438 6.802,1.583 0.156,0.146 10 false *4 3.396,1.063 3.521,1.208 0.125,0.146 10 false C 3.844,0.49 4.177,0.635 0.333,0.146 10 false A - A 5.667,0.49 6,0.635 0.333,0.146 10 false B - B 3.833,2.646 4.208,2.792 0.375,0.146 10 false C - C 5.594,2.646 5.938,2.792 0.344,0.146 10 false D - D

Text in Illustration
*1 Body Primer *2 Brush
*3 Adhesive *4 Edge of Curved Surface
*a CORRECT *b WRONG

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than that specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



b.

Using a brush or a sponge, coat the application area of the adhesive with glass primer.

B274735E02
5.156,2.438 5.417,2.438 false 5.167,0.927 5.427,0.927 false 2.25,2.25 2.365,2.396 0.115,0.146 10 true B 1.323,3.656 1.688,3.823 0.365,0.167 10 false A - A 3.771,3.656 4.177,3.833 0.406,0.177 10 false B - B 1.323,5.25 1.75,5.458 0.427,0.208 10 false C - C 5.427,2.375 5.583,2.521 0.156,0.146 10 false *1 5.438,0.865 5.583,1.01 0.146,0.146 10 false *2 0.5,6.563 0.708,6.719 0.208,0.156 10 false *3 0.438,6.552 0.5,6.698 0.063,0.146 10 false : 1.76,2.135 1.875,2.281 0.115,0.146 10 false B 3.24,2.177 3.354,2.323 0.115,0.146 10 true A 3.24,1.854 3.354,2 0.115,0.146 10 false A 3.219,2.906 3.344,3.052 0.125,0.146 10 true C 3.219,3.229 3.344,3.375 0.125,0.146 10 false C 0.146,0.125 0.344,0.292 0.198,0.167 10 false *A 1.958,4.188 2.063,4.333 0.104,0.146 10 false a 5,4.01 5.104,4.156 0.104,0.146 10 false b 4.26,3.917 4.365,4.063 0.104,0.146 10 false c 2.042,5.76 2.146,5.906 0.104,0.146 10 false d 1.958,6.031 2.063,6.177 0.104,0.146 10 false e

Text in Illustration
*A Back Side - -
*1 Adhesive Center *2 Ceramic Notch
*3 Glass Primer - -

Standard Dimension:
Area Dimension
a 13.0 mm (0.512 in.) or more
b 22.0 mm (0.866 in.) or more
c 30.9 mm (1.22 in.)
d 14.0 mm (0.551 in.) or more
e 9.7 mm (0.382 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer onto the ceramic notches.

·

If an area other than that specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.




c.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800E03
0.496,0.546 0.650,0.739 0.154,0.193 10 a 1.339,1.361 1.494,1.554 0.154,0.193 10 a 1.142,0.852 1.296,1.045 0.154,0.193 10 b 0.75,0.937 0.905,1.130 0.154,0.193 10 b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


HINT:

After cutting off the tip, use all the adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass as shown in the illustration.

B274736E02
5.156,2.438 5.417,2.438 false 5.167,0.938 5.427,0.938 false 2.25,2.25 2.365,2.396 0.115,0.146 10 true B 1.323,3.656 1.688,3.823 0.365,0.167 10 false A - A 3.771,3.656 4.177,3.833 0.406,0.177 10 false B - B 1.323,5.25 1.75,5.458 0.427,0.208 10 false C - C 5.427,2.375 5.583,2.521 0.156,0.146 10 false *1 5.448,0.865 5.594,1.01 0.146,0.146 10 false *2 0.365,6.563 0.573,6.719 0.208,0.156 10 false *3 0.302,6.552 0.365,6.698 0.063,0.146 10 false : 1.76,2.135 1.875,2.281 0.115,0.146 10 false B 3.24,2.177 3.354,2.323 0.115,0.146 10 true A 3.24,1.854 3.354,2 0.115,0.146 10 false A 3.219,2.906 3.344,3.052 0.125,0.146 10 true C 3.219,3.229 3.344,3.375 0.125,0.146 10 false C 0.146,0.125 0.344,0.292 0.198,0.167 10 false *A 1.708,4.177 1.813,4.323 0.104,0.146 10 false a 5.021,3.979 5.125,4.125 0.104,0.146 10 false b 4.396,3.854 4.5,4 0.104,0.146 10 false c 1.802,5.875 1.906,6.021 0.104,0.146 10 false a

Text in Illustration
*A Back Side - -
*1 Adhesive Center *2 Ceramic Notch
*3 Adhesive - -

Standard Dimension:
Area Dimension
a 6.0 mm (0.236 in.)
b 8.0 mm (0.315 in.)
c 31.9 mm (1.26 in.)




d.

Install the back door glass.

i.
B291625E01
1.389,0.851 1.546,1.000 0.157,0.149 10 *1 1.665,0.417 1.48,0.417 1.48,0.417 1.48,0.838 false 1.665,0.736 1.48,0.736 false

Position the back door glass so that the matchmarks are aligned, and press it in gently along the rim (when glass without clips is used).

Text in Illustration
*1 Matchmark


ii.

Lightly press the back door glass to ensure that the back door glass is securely fit to the vehicle body (when glass without a clip is used).

HINT:

Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.



iii.
B291627

Using suction cups, engage the 2 clips to install the back door glass (when glass with clips are used).

NOTICE:
·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and back door glass.




iv.

Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body (when glass with clips are used).

HINT:

Press the back door glass with a force of 98 N (10 kgf, 22 lbf) or more.



v.

Using a scraper, remove any excess or protruding adhesive.

Text in Illustration
*1 Adhesive

HINT:

Apply adhesive onto the glass rim.



vi.

Hold the back door glass using protective tape until applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle within the time described in the table below.


Minimum Time:
Temperature Minimum Time prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




e.

Connect the 2 connectors.


Hide 85110R 8.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 85143R 9.INSTALL REAR WIPER MOTOR GROMMET

Hide 10.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85292A 11.INSTALL REAR WIPER ARM HEAD CAP

Hide 13.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 67750 14.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

Hide 67938A 15.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 16.INSTALL BACK DOOR SIDE GARNISH RH

Hide 67939B 17.INSTALL BACK DOOR CENTER GARNISH

Hide 64886 18.INSTALL BACK WINDOW GLASS CHANNEL LH

Hide 64885A 19.INSTALL BACK WINDOW GLASS CHANNEL RH