Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2013.08–2014.11
RM2070E _59 Vehicle Exterior _061950 DOOR / HATCH _0301879 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 75756C 7.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75720 8.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67001A 9.INSTALL FRONT DOOR PANEL CUSHION

a.
B282924

Engage the 2 claws to install 2 new front door panel cushions.


Hide 67862 10.INSTALL FRONT DOOR WEATHERSTRIP

a.
B282923

Engage the 17 clips and install the front door weatherstrip.


Hide 68620 11.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door check assembly.


b.
B282922E03
2.198,1.833 2.427,2.01 0.229,0.177 10 true (A) 1.927,1.219 2.156,1.396 0.229,0.177 10 false (B) 2.125,0.229 2.354,0.406 0.229,0.177 10 false (B)

Apply adhesive to the threads of the bolt (A).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the front door check assembly with the 3 bolts.

Torque:
(A) : 30 N*m (306 kgf*cm, 22 ft.*lbf)
(B) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 67664C 12.INSTALL DOOR FRAME GARNISH

a.
B282895

Engage the clip to install a new door frame garnish.


Hide 69312 13.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B282925E03
3.063,1.063 3.26,1.25 0.198,0.188 10 false (1) 2.25,0.385 2.448,0.573 0.198,0.188 10 true (2)

Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 82152A 14.INSTALL FRONT DOOR WIRE (w/ Entry and Start System)

a.
B284803

Engage the 2 clamps to install the front door wire.


Hide 69202A 15.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B282926E03
0.115,0.104 0.302,0.271 0.188,0.167 10 false *a 0.115,2.333 0.302,2.5 0.188,0.167 10 true *b

Engage the door handle nut and claw.

Text in Illustration
*a Outside
*b Inside


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

w/ Entry and Start System:

i.
B282994

Engage the clamp.


ii.

Connect the connector.



Hide 69760C 16.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B282927

Install the front door inside locking cable assembly as shown in the illustration.


b.
B282928

Engage the 3 claws as shown in the illustration.


Hide 69720B 17.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B282929

Install the front door lock remote control cable assembly as shown in the illustration.


Hide 69320 18.INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
·

When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock assembly.


b.

When reusing the front door lock assembly:

i.
B282916

Install a new door lock wiring harness seal to the front door lock assembly.



c.
B282497E01
1.03,1.694 1.323,1.919 0.293,0.225 10 *1 1.099,1.674 0.802,1.069 false

Insert the front door lock open rod to the front door lock assembly.

Text in Illustration
*1 Front Door Lock Open Rod

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock assembly.



d.

Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the connector.


Hide 69242E 19.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B282914

Engage the 2 claws to install the front door rear outside handle pad.


Hide 69241H 20.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B282913

Engage the 3 claws to install the front door front outside handle pad.


Hide 69220 21.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B282931

Insert the front end of the front door outside handle assembly into the front door outside handle frame.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B282932

Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.


d.

w/ Entry and Start System:

i.
B282933

Connect the connector.


ii.

Engage the 2 claws.



Hide 69217D 22.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B282934

Engage the 2 guides and claw to install the front door outside handle cover to the front door lock cylinder.


Hide 69217D 23.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B282909

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B282908

Install the hole plug.


Hide 24.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B282935

Install the front door outside handle cover with lock cylinder assembly.

HINT:

Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



b.
B282906

Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B282905

Install the hole plug.


Hide 67404F 25.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B282936

Engage the guide as shown in the illustration.


b.

Install the front door rear lower frame sub-assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68151D 26.INSTALL FRONT DOOR GLASS RUN

a.
B282903

Install the front door glass run.


Hide 85720D 27.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor.


a.
B282902

Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 28.INSTALL FRONT DOOR POWER WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door power window regulator assembly.


b.

Install the temporary bolt to the front door power window regulator assembly.


c.
B282901E04
1.854,1.417 1.469,1.365 true 1.292,1.271 1.448,1.427 0.156,0.156 10 true *1

Temporarily install the front door power window regulator assembly.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the temporary bolt and 5 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 68102 29.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal and multiplex network master switch assembly.


d.
B282937E03
0.594,0.021 0.802,0.198 0.208,0.177 10 true (2) 1.635,0.073 1.844,0.25 0.208,0.177 10 false (1)

Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.


e.
B282899

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.
B282898

Install the grommet.


Hide 67832 30.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the front door panel.


b.
B282938E01
0.158,0.172 0.330,0.333 0.171,0.161 10 *1 3.085,0.189 3.257,0.350 0.171,0.161 10 *1 2.505,2.951 2.677,3.112 0.171,0.161 10 *1

Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.

Attach the front door service hole cover according to the reference points on the front door panel.

Text in Illustration
*1 Reference Point

NOTICE:

Securely install the front door service hole cover preventing wrinkles and air bubbles.



Hide 67626 31.INSTALL FRONT DOOR TRIM BRACKET

a.
B282896

Install the front door trim bracket with the 2 screws.


Hide 33.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Hide 87964 34.INSTALL OUTER MIRROR INSTALL HOLE COVER

Hide 81230 36.INSTALL COURTESY LIGHT ASSEMBLY

Hide 69206B 37.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B276424

Engage the 2 claws to install the front door inside handle sub-assembly to the front door trim board sub-assembly.


Hide 68172A 38.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B282939

Engage the 7 claws to install the front door inner glass weatherstrip to the front door trim board sub-assembly as shown in the illustration.


Hide 67602 39.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B282940E03
2.448,1.917 2.521,1.698 false 2.667,1.406 3.021,1.208 false 3.042,1.104 3.198,1.26 0.156,0.156 10 false *1 2.344,1.927 2.5,2.083 0.156,0.156 10 true *2

Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.

Text in Illustration
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


b.

Connect the courtesy light connector.


c.
B282941

Engage the 9 clips and install the front door trim board sub-assembly.


d.

Install the 2 screws.


e.

If protective tape has been applied, remove it.


Hide 74222 40.INSTALL DOOR ARMREST COVER

a.
B276420

Install the door armrest cover.


Hide 41.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect the connector.


b.
B314454

Engage the 4 guides, 11 claws and clip to install the multiplex network master switch assembly with front door armrest base panel.


Hide 42.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B314456

Engage the 4 guides, 11 claws and clip to install the power window regulator switch assembly with front door armrest base panel.


Hide 69284C 43.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B314468

Engage the 3 claws to install the front door inside handle bezel plug.


Hide 44.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 50.INITIALIZE POWER WINDOW CONTROL SYSTEM