Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339647 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  


DESCRIPTION

The forward recognition camera receives vehicle stability signals from the yaw rate sensor (airbag ECU assembly). If the yaw rate sensor (airbag ECU assembly) detects an abnormal yaw rate sensor signal or yaw rate sensor power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit When all of the following conditions are met:
·

2 seconds after the power switch is turned on (IG)

·

The vehicle speed is 1 km/h or 1 mph or more.

·

A signal from the yaw rate sensor (airbag ECU assembly) indicating a malfunction in the yaw rate sensor is detected by the forward recognition camera for 5 seconds or more.


·

Electronically controlled brake system

·

Yaw rate sensor (Airbag ECU assembly)

·

Forward recognition camera


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit When all of the following conditions are met:
·

2 seconds after the power switch is turned on (IG)

·

The vehicle speed is 1 km/h or 1 mph or more.

·

A signal from the yaw rate sensor (airbag ECU assembly) indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more.


·

Electronically controlled brake system

·

Yaw rate sensor (Airbag ECU assembly)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

The lane departure alert system (w/ steering control) uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

Lane departure alert system (w/ steering control) DTC C1AA4 or C1AA5 may be stored due to a malfunction in the electronically controlled brake system. Therefore it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.



Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))

B

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.

2.

Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.





Result:
Result Proceed to
DTC C1AA4 and C1AA5 are not output A
DTC C1AA4 or C1AA5 is output B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))
4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.

2.

Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.





Result:
Result Proceed to
DTC C1AA4 and C1AA5 are not output A
DTC C1AA4 or C1AA5 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B