88211B
1.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
89341A
2.REMOVE NO. 1 ULTRASONIC SENSOR (w/ Intelligent Parking Assist System)
89348
3.REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intelligent Parking Assist System)
81440B
4.REMOVE DAYTIME RUNNING LIGHT ASSEMBLY LH
81430C
5.REMOVE DAYTIME RUNNING LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
82113
6.REMOVE NO. 3 ENGINE ROOM WIRE
Disengage the 11 clamps to remove the No. 3 engine room wire.
81220
7.REMOVE FOG LIGHT ASSEMBLY LH
81210A
8.REMOVE FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
53395E
9.REMOVE HOOD TO FRONT END PANEL SEAL
Disengage the 2 clips and remove the hood to front end panel seal.
53111
10.REMOVE RADIATOR GRILLE
Remove the 2 screws.
Remove the 4 clips.
Disengage the 16 claws and guide to remove the radiator grille.
75301A
11.REMOVE FRONT BUMPER EMBLEM SUB-ASSEMBLY
Remove the 2 screws.
Disengage the 2 claws to remove the front bumper emblem sub-assembly.
53113E
12.REMOVE LOWER NO. 2 RADIATOR GRILLE
Remove the 2 screws.
Disengage the 6 claws to remove the lower No. 2 radiator grille.
53102A
13.REMOVE LOWER RADIATOR GRILLE SUB-ASSEMBLY
Remove the 2 screws.
Remove the 4 outside moulding retainers.
Disengage the 14 claws and 4 guides to remove the lower radiator grille sub-assembly.
52128B
14.REMOVE FRONT BUMPER HOLE COVER LH
Disengage the 2 claws.
| *a | Hook |
Disengage the hook to remove the front bumper hole cover LH.
52127C
15.REMOVE FRONT BUMPER HOLE COVER RH
Use the same procedure as for the LH side.
52822
16.REMOVE AIR INTAKE DUCT LH
Use the same procedure as for the LH side.
Using a screwdriver, turn the pin 90 degrees and remove the 3 pin hold clips.
| *1 | Pin Hold Clip |
| *a | 90° |
Remove the 2 screws and air intake duct LH.
52821
17.REMOVE AIR INTAKE DUCT RH
Use the same procedure as for the LH side.
53879A
18.REMOVE FRONT FENDER LINER RETAINER
Disengage the claw to remove the 3 front fender liner retainers.
Use the same procedure for the RH side and LH side.
52113D
19.REMOVE FRONT BUMPER EXTENSION LH
Disengage the 2 claws to remove the front bumper extension LH.
52112D
20.REMOVE FRONT BUMPER EXTENSION RH
Use the same procedure for the RH side and LH side.
52611
21.REMOVE FRONT BUMPER ENERGY ABSORBER
Disengage the 2 guides to remove the front bumper energy absorber.
52021
22.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Using a clip remover, disengage the 3 clamps.
Remove the 6 bolts.
Disengage the claw and remove the front bumper reinforcement sub-assembly.
52116A
23.REMOVE FRONT BUMPER SIDE SUPPORT LH
Remove the bolt and screw.
| *a | Bolt |
| *b | Screw |
Disengage the 2 claws and remove the front bumper side support LH.
52115A
24.REMOVE FRONT BUMPER SIDE SUPPORT RH
Use the same procedure as for the LH side.
57014A
25.REMOVE FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH
Remove the 4 bolts.
Disengage the guide and remove the front side member bracket sub-assembly LH.
57013C
26.REMOVE FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH
Use the same procedure as for the LH side.