Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › from 2017.12
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301607 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Side)

Hide 3.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Center)

Hide 4.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 58325E 5.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A248043

Using a clip remover, remove the 2 clips.


b.

Turn over the front floor carpet.


c.
A251243

Remove the rear floor service hole cover.


d.
A248044

Disconnect the connector from the fuel suction tube assembly.


Hide 6. DISCHARGE FUEL SYSTEM PRESSURE

Hide 12.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77209F 13.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A248045E02
2.177,3.583 2.49,3.583 false 1.51,3.25 1.083,3.25 false 1.896,3.792 2.438,3.792 2.438,3.792 2.438,4.135 false 1.896,3.927 2.438,3.927 false 0.583,2.094 0.583,2.635 false 0.51,2.646 0.667,2.885 0.156,0.24 10 false *1 2.521,3.5 2.677,3.74 0.156,0.24 10 false *1 0.896,3.156 1.094,3.385 0.198,0.229 10 false *2 2.354,4.156 2.573,4.406 0.219,0.25 10 false *3

Remove the tube joint clip, then pull the fuel tube joint out of the plug of the fuel suction tube with pump and gauge assembly.

Text in Illustration
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 O-ring

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77754B 14.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A248046

Disconnect the charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.


Hide 77026A 15.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A248047

Loosen the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction tube with pump and gauge assembly.


Hide 77144 16.REMOVE FUEL PUMP GAUGE RETAINER

NOTICE:

Before performing these procedures, first cover the connector and fuel tube joint of the fuel suction tube with pump and gauge assembly with vinyl tape and then clean any dirt and foreign matter in order to prevent contamination of the fuel system.


a.
A413973C02
0.823,0.177 1.156,0.177 true 0.604,0.563 0.969,0.563 true 0.615,0.906 1.385,0.906 1.385,0.906 1.385,0.521 true 2.396,2.052 2.802,2.052 true 2.188,1.792 2.885,1.792 true 1.146,0.906 1.146,0.688 true 0.438,0.833 0.75,0.99 0.313,0.156 10 false *a 2.938,1.729 3.25,1.885 0.313,0.156 10 false *b 0.635,0.104 0.948,0.26 0.313,0.156 10 false *c 2.854,1.99 3.167,2.146 0.313,0.156 10 false *d 0.417,0.49 0.729,0.646 0.313,0.156 10 false *c
*a Fully Tightened Mark on Fuel Tank Assembly
*b Start of Threads Mark on Fuel Tank Assembly
*c Copy of Fully Tightened Mark
*d Copy of Start of Threads Mark
V100135

Front


Copy the start of threads mark and fully tightened marks from the fuel tank assembly to the vehicle body in order to record their locations.


b.
A413974C02
0.885,1 0.823,1.458 0.823,1.458 1.219,1.094 true 0.698,1.479 0.906,1.646 0.208,0.167 10 true *a
*a Paint Mark
V100135

Front


Place paint marks on the fuel suction tube with pump and gauge assembly and vehicle body as shown in the illustration.

NOTICE:
·

The fuel suction tube with pump and gauge assembly has a protrusion that engages with a notch on the fuel tank assembly to ensure correct alignment and to prevent the fuel suction tube with pump and gauge assembly from turning during installation and removal of the fuel pump gauge retainer.

·

If the fuel pump gauge retainer is turned with the fuel suction tube with pump and gauge assembly misaligned, the fuel suction tube with pump and gauge assembly will turn with the fuel pump gauge retainer and may be damaged.

·

The paint marks are used to ensure that the fuel suction tube with pump and gauge assembly does not turn with the fuel pump gauge retainer.




c.

Install SST to the fuel pump gauge retainer.

i.
A381189C02
2.115,0.208 2.26,0.208 2.26,0.208 2.385,0.375 false 0.604,1.24 0.906,1.24 false 1.208,1.385 1.51,1.385 false 1.177,2.167 1.406,2.167 false 1.115,2.406 1.229,2.406 1.229,2.406 1.563,2.573 true 1.854,2.573 1.99,2.344 1.99,2.344 2.083,2.344 false 1.104,3.104 1.292,3.104 1.292,3.104 1.563,2.677 true 0.563,4.458 0.75,4.458 0.75,4.458 1.385,4.042 true 2.604,1.708 2.604,1.469 false 1.563,1.313 1.875,1.469 0.313,0.156 10 false *1 0.438,1.156 0.75,1.313 0.313,0.156 10 false *a 0.917,3.031 1.229,3.188 0.313,0.156 10 false *b 0.938,2.333 1.25,2.49 0.313,0.156 10 false *c 0.375,4.396 0.688,4.552 0.313,0.156 10 false *d 1.948,0.146 2.26,0.302 0.313,0.156 10 false *1 1.01,2.083 1.323,2.24 0.313,0.156 10 false *a 2.146,2.281 2.458,2.438 0.313,0.156 10 false *1 2.531,1.729 2.844,1.885 0.313,0.156 10 false *a
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Protrusion
*c Notch
*d Do not install SST (Claw Set)


Set 4 SST (claw set) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the notch of SST (claw set) with the protrusion of the fuel pump gauge retainer.

·

Do not install SST (claw set) to the start of threads location of the fuel pump gauge retainer.




ii.
A381190C02
1.031,0.396 1.302,0.396 false 0.927,2.052 1.063,2.052 1.063,2.052 1.229,1.823 false 2.135,1.302 2.24,1.052 2.24,1.052 2.344,1.052 false 2.406,0.979 2.719,1.135 0.313,0.156 10 false *1 0.844,0.313 1.156,0.469 0.313,0.156 10 false *a 0.75,1.979 1.063,2.135 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Push
V100136

SST (Bolt)


Push SST (claw set) against the fuel pump gauge retainer and tighten SST (bolt).


iii.
A413975C02
0.583,0.833 0.854,0.833 false 0.563,1.177 1.01,1.177 true 0.979,1.75 1.688,1.75 true 2.438,1.115 2.917,1.115 true 0.406,0.771 0.719,0.927 0.313,0.156 10 false *a 0.396,1.125 0.708,1.281 0.313,0.156 10 false *b 0.802,1.698 0.979,1.844 0.177,0.146 10 true *b 2.969,1.052 3.281,1.208 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SST (bolt).

SST
09808-14031  (09808-01030, 09808-01090)


iv.
A413976C02
0.656,0.552 1.031,0.552 1.031,0.552 1.729,1.198 true 0.521,1.125 0.948,1.125 true 0.479,0.469 0.792,0.625 0.313,0.156 10 false *a 0.344,1.052 0.656,1.208 0.313,0.156 10 false *b
*a Center Point of Fuel Pump Gauge Retainer
*b SST (Plate)
V100135

Front


Adjust the position of SST (claw set) so that the hole in SST (plate) for installing SST (handle) is in the center of the fuel pump gauge retainer.


v.
A413977C02
1.146,0.104 1.365,0.104 1.365,0.104 1.771,0.188 true 1.115,0.302 1.458,0.302 true 1.188,0.552 1.344,0.552 1.344,0.552 1.646,0.708 true 1.75,1.948 1.896,1.948 1.896,1.948 2.135,1.563 true 1.583,1.896 1.896,2.052 0.313,0.156 10 false *1 0.948,0.24 1.26,0.396 0.313,0.156 10 false *a 1.021,0.5 1.333,0.656 0.313,0.156 10 false *b 0.969,0.031 1.281,0.188 0.313,0.156 10 false *c
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
V100135

Press


Press SST (claw set) against the rib of the fuel pump gauge retainer and tighten SST (bolt).


vi.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)



d.
A413978C02
0.781,0.229 0.948,0.229 0.948,0.229 1.115,0.656 true 0.875,1.104 0.875,0.958 0.875,0.958 1.063,0.938 true 0.76,1.115 0.948,1.281 0.188,0.167 10 true *a 0.615,0.167 0.927,0.323 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Handle)
V100135

Loosen


Slowly loosen the fuel pump gauge retainer by approximately 90°.

NOTICE:

Do not spin SST too fast or use an impact wrench as this may result in damage to components.



e.

While one person loosens the fuel pump gauge retainer, have another person press down the rising fuel suction tube with pump and gauge assembly, securely insert the protrusion of the fuel suction tube with pump and gauge assembly into the groove of the fuel tank assembly, and then remove the fuel pump gauge retainer while making sure that the fuel suction tube with pump and gauge assembly is properly aligned.

A413979C02
1.104,0.625 1.219,0.625 1.219,0.625 1.365,1.125 false 1.417,2.24 1.417,2.073 1.417,2.073 1.844,1.698 true 4.958,2.292 4.958,2.063 4.958,2.063 5.26,1.708 true 2.917,3.49 2.844,3.813 2.844,3.813 3.177,3.552 true 1.323,2.26 1.635,2.417 0.313,0.156 10 false *a 0.927,0.552 1.24,0.708 0.313,0.156 10 false *b 0.927,1.135 1.24,1.292 0.313,0.156 10 false *c 1.583,0.885 1.896,1.042 0.313,0.156 10 false *d 2.719,3.854 2.885,4.01 0.167,0.156 10 true *e 4.875,2.323 5.188,2.479 0.313,0.156 10 false *a 2.719,1.115 3.031,1.271 0.313,0.156 10 false *c 4.76,1.25 5.073,1.406 0.313,0.156 10 false *c 5.771,1.25 6.083,1.406 0.313,0.156 10 false *c 2.146,0.875 2.458,1.031 0.313,0.156 10 false *d 5.01,0.875 5.323,1.031 0.313,0.156 10 false *d 5.552,0.906 5.865,1.063 0.313,0.156 10 false *d
*a SST (Plate) *b SST (Handle)
*c One Person in Charge of Loosening *d One Person in Charge of Pressing Down
*e Paint Mark - -


NOTICE:
·

The fuel suction tube with pump and gauge assembly is pressed against the underside of the fuel tank assembly by a spring, and the constant upward pressure applied by this spring causes the fuel suction tube with pump and gauge assembly to rise up.

·

If the fuel pump gauge retainer is turned while the fuel suction tube with pump and gauge assembly and fuel tank assembly are not correctly aligned, the fuel suction tube with pump and gauge assembly will move with the fuel pump gauge retainer, and the fuel suction tube with pump and gauge assembly and fuel tank assembly may both be damaged.

·

Do not turn the fuel pump gauge retainer if the paint marks become misaligned.




Hide 77020A 17.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A251244

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A251210E01
2.836,0.188 3.009,0.382 0.173,0.194 10 *1 2.606,0.442 2.752,0.295 2.752,0.295 2.833,0.295 false

Remove the fuel suction tube set gasket from the fuel tank assembly.

Text in Illustration
*1 Fuel Suction Tube Set Gasket