Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2017.12
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301860 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 58410B 1.REMOVE DECK BOARD ASSEMBLY

a.

Remove the deck board assembly.


Hide 58411A 2.REMOVE NO. 1 DECK BOARD

a.

Remove the No. 1 deck board.


Hide 58412A 3.REMOVE NO. 2 DECK BOARD

a.

Remove the No. 2 deck board.


Hide 64993 4.REMOVE REAR DECK FLOOR BOX

a.

Remove the rear deck floor box.


Hide 64995 5.REMOVE DECK FLOOR BOX RH

a.
B274262

Disengage the 3 claws and remove the deck floor box RH.


Hide 64910J 6.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.

Remove the tonneau cover assembly.


Hide 67935A 7.REMOVE BACK DOOR SCUFF PLATE

a.
B274276

Disengage the 2 claws, 4 clips and 2 guides and remove the back door scuff plate.


Hide 72127D 8.REMOVE SEAT TRACK BRACKET COVER RH

Hide 72159H 9.REMOVE REAR SEAT TRACK BRACKET COVER

Hide 72128C 10.REMOVE SEAT TRACK BRACKET COVER LH

Hide 11.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 67914 12.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B282780

Disengage the 10 claws and remove the front door scuff plate LH.


Hide 62112A 13.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

a.
B282781

Remove the clip.


b.

Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


Hide 62312B 14.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the front door opening trim weatherstrip LH.


Hide 62212 15.REMOVE FRONT PILLAR GARNISH LH

a.
B448123E02
0.656,0.906 0.792,0.521 true 0.594,0.927 0.75,1.073 0.156,0.146 10 false *1

Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

Text in Illustration
*1 Front Pillar Garnish Clip

HINT:

Let the front pillar garnish LH hang from the front pillar garnish clip.



b.
B448124

While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

NOTICE:
·

The front pillar garnish clip is reusable if it is not damaged.

·

If the front pillar garnish clip is damaged, replace it with a new one.



HINT:

When the front pillar garnish clip cannot be disengaged easily:

1.
B448115

While pushing the tab of the front pillar garnish clip with your finger, move the front pillar garnish clip in the direction shown in the illustration.

Text in Illustration
V113147

Move in this Direction

2.
B448127

While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip with a screwdriver and disengage the front pillar garnish clip.

Text in Illustration
V113147

Pull in this Direction




c.
B448121E02
2.583,2.865 2.698,3.01 0.115,0.146 10 false B 0.719,1.677 0.833,1.823 0.115,0.146 10 false A 1.688,2.427 1.802,2.573 0.115,0.146 10 false A 2.656,1.521 2.76,1.667 0.104,0.146 10 false 2 2.063,0.677 2.167,0.823 0.104,0.146 10 false 3 1.292,1.635 1.396,1.781 0.104,0.146 10 true 1

Disengage the 2 guides (A).


d.

Disengage the guide (B) while pressing the shaded part in the illustration in the direction indicated by the arrow (2).


e.

Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (3) in the illustration.


f.
B282784E02
1.72,0.2 1.877,0.349 0.157,0.149 10 *2 1.009,1.171 1.166,1.320 0.157,0.149 10 *3 2.179,0.467 2.336,0.616 0.157,0.149 10 *1 1.77,0.67 2.164,0.548 false 1.061,0.453 1.698,0.285 false 1.097,0.814 1.097,1.156 false

Protect the curtain shield airbag assembly.

Text in Illustration
*1 Adhesive Tape
*2 Protective Cover
*3 Curtain Shield Airbag Assembly

i.

Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.




Hide 67918A 16.REMOVE REAR DOOR SCUFF PLATE LH

a.

Move the rear seat assembly LH to the foremost position.


b.
B282785

Disengage the 9 claws and 3 clips, and remove the rear door scuff plate LH.


Hide 62332A 17.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the rear door opening trim weatherstrip LH.


Hide 73233 18.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 73220 19.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 20.REMOVE CENTER PILLAR LOWER GARNISH LH

a.
B282786

Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.


Hide 62412 21.REMOVE CENTER PILLAR GARNISH LH

a.
B282787

Remove the bolt.


b.

Disengage the 2 clips.


c.

Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.


Hide 67913 22.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111C 23.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 24.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 25.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 26.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62331A 27.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 28.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 73210 29.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 30.REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62411 31.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 64721G 32.REMOVE NO. 1 DECK TRIM COVER (for LH Side)

a.
B313172

Using a moulding remover, disengage the 3 claws.


b.

Disengage the 2 guides and remove the No. 1 deck trim cover.


Hide 58460D 33.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

a.
B313174

Remove the 2 bolts.


b.

Disengage the 2 guides and remove the 2 luggage hold belt striker assemblies.


Hide 64713F 34.REMOVE FRONT DECK SIDE TRIM COVER LH

a.
B317539

Using a moulding remover, disengage the 2 claws.


b.

Disengage the 2 guides and remove the front deck side trim cover LH.


Hide 55548C 35.REMOVE NO. 2 CUP HOLDER

a.
B274307

Disengage the 12 claws and remove the No. 2 cup holder.


Hide 73370C 36.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Hide 73570 37.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Lower Side)

Hide 81250 38.REMOVE NO. 2 ROOM LIGHT ASSEMBLY

Hide 64740C 39.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Remove the 2 bolts.

B313175


b.

Disengage the 7 claws, 5 clips and 5 guides, and remove the deck trim side panel assembly LH.


Hide 73570 40.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Upper Side)

Hide 62480A 41.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

a.
B282791

Using a moulding remover, disengage the 2 claws and 2 guides, and disconnect the belt guide LH.


b.

Pull the roof side inner garnish assembly LH in the direction indicated by the arrow (1) shown in the illustration to disengage the 7 clips (A).

B282792E03
2.542,2 2.74,2.167 0.198,0.167 10 true (1) 4.167,1.063 4.365,1.229 0.198,0.167 10 false (2) 2.688,1.115 2.896,1.281 0.208,0.167 10 true (A) 3.302,0.854 3.51,1.021 0.208,0.167 10 false (B) 4.271,0.531 4.479,0.698 0.208,0.167 10 false (B) 3.615,0.781 3.823,0.948 0.208,0.167 10 true (B) 2.583,1.458 2.792,1.625 0.208,0.167 10 true (A) 2.823,1.583 3.031,1.75 0.208,0.167 10 false (A) 3.771,1.604 3.979,1.771 0.208,0.167 10 true (A) 4.719,0.938 4.927,1.104 0.208,0.167 10 false (A) 4.083,1.719 4.292,1.885 0.208,0.167 10 true (A) 3.5,1.448 3.708,1.615 0.208,0.167 10 true (A)


c.

Pull the roof side inner garnish assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the 3 clips (B) and remove the roof side inner garnish assembly LH and rear roof side rail garnish as a unit.


Hide 62452C 42.REMOVE REAR ROOF SIDE RAIL GARNISH LH

a.
B282793

Disengage the 4 claws and guide, and remove the rear roof side rail garnish LH.


Hide 64721G 43.REMOVE NO. 1 DECK TRIM COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 58460D 44.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64712F 45.REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 55548C 46.REMOVE NO. 1 CUP HOLDER

a.
B274280

Disengage the 12 claws.


b.

Disconnect the connector and remove the No. 1 cup holder.


Hide 73360C 47.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73560 48.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Lower Side)

HINT:

Use the same procedure as for the LH side.


Hide 64730B 49.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73560 50.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Upper Side)

HINT:

Use the same procedure as for the LH side.


Hide 62471A 51.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62451C 52.REMOVE REAR ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 87818 53.REMOVE INNER REAR VIEW MIRROR COVER (w/ Cover)

Hide 89943 54.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 86466E 55.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86466D 56.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 81260A 57.REMOVE MAP LIGHT ASSEMBLY (except Glass Roof)

Hide 81260A 58.REMOVE MAP LIGHT ASSEMBLY (for Glass Roof)

Hide 81240 59.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 73139A 60.REMOVE SEAT BELT ANCHOR COVER

a.
B273819

Using a moulding remover, disengage the 2 clips as shown in the illustration.


b.

Disengage the 2 claws and 2 guides, and remove the seat belt anchor cover.


Hide 74610S 61.REMOVE FRONT ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for all front assist grip assemblies.


a.
B484978C01
2.115,0.51 2.5,0.51 true 2.302,3.24 2.729,3.24 true 2.531,0.417 2.76,0.594 0.229,0.177 10 true *a 2.781,3.167 3.125,3.344 0.344,0.177 10 false SST
*a Cutout


Insert SST into the cutout of the assist grip cover as shown in the illustration.

SST
09813-00010  

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.



b.
B484979C01
2.583,1.5 2.938,1.5 true 2.052,2.01 2.365,2.167 0.313,0.156 10 false *a 2.958,1.427 3.292,1.604 0.333,0.177 10 true SST
*a 30 to 45°
V100135

Remove in this Direction


Pull SST as shown in the illustration to disengage the claw.

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.


HINT:

Use the same procedure for the claw on the other side of the assist grip cover.



c.

Remove the assist grip cover.

HINT:

Use the same procedure for the LH side and RH side.



d.
B229261

Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.


e.

Remove the 2 clips from the vehicle body.


Hide 74620B 62.REMOVE REAR ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure as for the front assist grip assembly.


Hide 74320 63.REMOVE VISOR ASSEMBLY LH

a.
B316632

Remove the 2 screws and visor assembly LH.


Hide 74310 64.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74348 65.REMOVE VISOR HOLDER

a.
B211697E04
1.094,0.292 1.563,0.563 0.469,0.271 10 false 45°

Turn the visor holder approximately 45° and pull it out as shown in the illustration.


b.

Disengage the 2 claws and remove the visor holder.

HINT:

Use the same procedure for the other visor holder.



Hide 66.DISCONNECT ROOF HEADLINING ASSEMBLY (except Glass Roof)

a.

for Windshield Glass Side:

i.

w/ EC mirror or Pre-crash Safety System:

1.

Disconnect each connector.




b.

for Front Pillar LH Side:

i.

Remove the protective cover.


ii.

Disengage the 3 clamps.

B499855C01
0.167,0.198 0.667,0.552 0.5,0.354 12 false *A 0.177,1.771 0.542,2.042 0.365,0.271 12 false *B 2.792,4.854 3.104,5.104 0.313,0.25 12 true *C 4.927,4.844 5.24,5.094 0.313,0.25 12 true *D 2.635,0.188 2.948,0.438 0.313,0.25 12 true *E 5.333,0.188 5.646,0.438 0.313,0.25 12 true *F 5.958,0.75 6.24,0.969 0.281,0.219 12 true *G
*A w/o Digital Audio Broadcasting Antenna *B w/ Digital Audio Broadcasting Antenna
*C for RHD without Pre-crash Safety System *D except RHD without Pre-crash Safety System
*E w/o Radio Receiver *F w/ Radio Receiver
*G w/ Navigation Receiver - -



iii.

Disconnect each connector.


iv.

Install the protective cover.



c.

for Front Pillar RH Side:

i.

Remove the protective cover.


ii.

Disengage the 3 clamps.


iii.

Disconnect each connector.


iv.

Install the protective cover.



d.

for Rear Pillar RH Side:

i.

w/o Radio Receiver:

1.

Disengage the claw.

2.

Disconnect the connector.



ii.

w/ Radio Receiver:

1.

Disengage the claw and guide.

2.

Disconnect each connector.




e.

Remove the 5 clips and temporarily set down the roof headlining assembly in the cabin.


Hide 67.DISCONNECT ROOF HEADLINING ASSEMBLY (for Glass Roof)

a.

for Windshield Glass Side:

i.

Disconnect each connector.



b.

for Front Pillar LH Side:

i.

Remove the protective cover.


ii.

Disengage the 3 clamps.

B499856C01
0.188,0.198 0.563,0.438 0.375,0.24 12 false *A 0.177,1.813 0.552,2.052 0.375,0.24 12 false *B 2.635,0.208 2.917,0.427 0.281,0.219 12 true *C 5.229,0.208 5.51,0.427 0.281,0.219 12 true *D 5.958,0.74 6.24,0.958 0.281,0.219 12 true *E
*A w/o Digital Audio Broadcasting Antenna *B w/ Digital Audio Broadcasting Antenna
*C w/o Radio Receiver *D w/ Radio Receiver
*E w/ Navigation Receiver - -



iii.

Disconnect the 2 connectors.


iv.

Install the protective cover.



c.

for Front Pillar RH Side:

i.

Remove the protective cover.


ii.

Disengage the 3 clamps.


iii.

Disconnect each connector.


iv.

Install the protective cover.



d.

for Rear Pillar RH Side:

i.

w/o Radio Receiver:

1.

Disengage the claw.

2.

Disconnect the connector.



ii.

w/ Radio Receiver:

1.

Disengage the claw and guide.

2.

Disconnect each connector.




e.

Remove the 3 clips.


f.

Disengage the 15 fasteners and temporarily set down the roof headlining assembly in the cabin.

B317524


Hide 56111 68.REMOVE WINDSHIELD GLASS

Hide 69.REMOVE ROOF HEADLINING ASSEMBLY

a.
B282880

Remove the roof headlining assembly through the front of the vehicle.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.