Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL › from 2017.12
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301857 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL UPPER INSTRUMENT PANEL ASSEMBLY

a.

When using a new upper instrument panel sub-assembly:

i.

Immediately before installing the upper instrument panel assembly, twist and cut off the portion shown in the illustration.

B282846



b.

Engage the 5 claws (B) as shown in the illustration.

B282847E03
3.583,2.198 3.823,2.385 0.24,0.188 10 true (1) 2.635,1.823 2.833,1.99 0.198,0.167 10 true (2) 0.865,2.708 1.094,2.875 0.229,0.167 10 false (A) 0.208,2.75 0.438,2.917 0.229,0.167 10 true (A) 1.479,2.469 1.708,2.635 0.229,0.167 10 true (A) 2,2.458 2.229,2.625 0.229,0.167 10 true (A) 4.073,2.615 4.302,2.781 0.229,0.167 10 true (A) 5.708,3.479 5.938,3.646 0.229,0.167 10 true (A) 6.542,3.781 6.771,3.948 0.229,0.167 10 false (A) 6.146,1.688 6.375,1.854 0.229,0.167 10 true (B) 5.115,1.604 5.344,1.771 0.229,0.167 10 true (B) 3.667,1.448 3.896,1.615 0.229,0.167 10 true (B) 2.802,1.417 3.052,1.604 0.25,0.188 10 true (B) 1.677,1.375 1.906,1.542 0.229,0.167 10 true (B)


c.

Engage the 7 claws (A) as shown in the illustration.

NOTICE:
·

Do not damage the upper instrument panel assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.




d.

Install the 2 bolts <A>.


e.

Install the 2 passenger airbag bolts <B>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


f.

Connect the connector to install the upper instrument panel assembly.


Hide 55414A 3.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (w/ Headup Display)

a.
B492162N01
1.229,0.552 1.385,0.74 0.156,0.188 10 false 1 0.792,1.292 0.948,1.479 0.156,0.188 10 false 2

Engage the 2 guides and 5 claws to install the instrument cluster finish panel end as shown in the illustration.


Hide 55404D 4.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

Engage the 3 guide and 2 clips.


b.

Install the instrument cluster finish panel sub-assembly with the 2 screws <D> and 3 clips.


Hide 55085 5.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B282848

Engage the 2 guides as shown in the illustration.


b.

Install the No. 2 heater to register duct sub-assembly with the 2 clips.


Hide 55406B 6.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B282849E03
2.615,2.135 2.833,2.323 0.219,0.188 10 true (1) 1.49,2.792 1.719,2.979 0.229,0.188 10 true (2)

Engage the 2 claws to install the lower center instrument cluster finish panel sub-assembly as shown in the illustration.


Hide 7.INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

a.

Engage the 8 claws to install the center instrument panel register assembly.


Hide 86160P 8.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

HINT:

Use the same procedure as for the LH side (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION).


Hide 55409F 9.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B273245

Engage the 2 guides and 5 claws to install the No. 2 instrument panel speaker panel sub-assembly.


Hide 62225A 10.INSTALL LOWER FRONT PILLAR GARNISH RH

a.
B274882

Engage the 3 claws to install the lower front pillar garnish RH.


Hide 62211 11.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION)


Hide 55435A 12.INSTALL INSTRUMENT PANEL FINISH PANEL END RH

a.

Connect the connector.


b.
B318023

Engage the guide as shown in the illustration.


c.
B318024

Engage the guide and 6 claws to install the instrument panel finish panel end RH as shown in the illustration.


Hide 62311B 13.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 55620C 14.INSTALL INSTRUMENT PANEL CUP HOLDER

a.

Install the instrument panel cup holder with the 2 screws <E>.


Hide 15.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B282852

Engage the 6 claws.


b.

Install the No. 2 instrument panel register assembly with the screw <C>.


Hide 55440D 16.INSTALL INSTRUMENT PANEL BOX ASSEMBLY

a.

Open the instrument panel box and glove compartment door.


b.
B282853

Engage the 8 claws to install the instrument panel box assembly.


c.

Close the instrument panel box and glove compartment door.


Hide 55408F 18.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B274880

Engage the 2 guides and 5 claws to install the No. 1 instrument panel speaker panel sub-assembly.


Hide 62226 19.INSTALL LOWER FRONT PILLAR GARNISH LH

a.
B274884

Engage the 3 claws to install the lower front pillar garnish LH.


Hide 55436A 21.INSTALL INSTRUMENT PANEL FINISH PANEL END LH

a.
B282854

Engage the guide as shown in the illustration.


b.
B282855

Engage the guide and 6 claws to install the instrument panel finish panel end LH as shown in the illustration.


Hide 62312B 22.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 23.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

w/ Headup display:

i.

Connect the connector.



b.
B313756

Engage the 6 claws to install the No. 1 instrument panel register assembly.


Hide 55044B 24.INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.
B282857

Engage the 8 claws to install the upper instrument panel finish panel sub-assembly.


Hide 55480D 25.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.

Engage each connector.


b.

Engage the 8 claws and clip to install the lower instrument panel finish panel assembly.


Hide 55431B 26.INSTALL UPPER INSTRUMENT PANEL FINISH PANEL

a.

Engage the 2 claws and clip to install the upper instrument panel finish panel.


Hide 27.INSTALL INTEGRATION CONTROL AND PANEL

a.

Engage each connector.


b.

Engage the 8 claws to install the integration control and panel.


Hide 28.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).