The skid control ECU inputs steering angle sensor signals via the CAN communication system. When a malfunction occurs in the communication line with the steering angle sensor, DTC U0126 (Lost Communication With Steering Angle Sensor Module) is output.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1231 | 701 | While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (sensor malfunction). | Steering angle sensor internal malfunction |
| ↑ | 702 | While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (internal malfunction). | ↑ |
| ↑ | 703 | While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (+B malfunction). | ↑ |
When U0126 is output together with C1231, inspect and repair the trouble areas indicated by U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073).
When the speed sensor or the yaw rate and acceleration sensor (airbag ECU assembly) are malfunctioning, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag ECU assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) first, and then inspect and repair the steering angle sensor.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off (lock).
Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM for with Central Gateway ECU or Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM for without Central Gateway ECU).
Drive the vehicle and turn the steering wheel to the right and left at the speed of 35 km/h (22 mph) and check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC (C1231) is output | A |
| CAN communication system DTC is output (w/ Central Gateway ECU) | B |
| CAN communication system DTC is output (w/o Central Gateway ECU) | C |
| Speed sensor and/or yaw rate and acceleration sensor DTC is output | D |
| DTC (C1231) is not output | E |
When DTCs indicating CAN communication system malfunctions are output, repair the CAN communication system before repairing each corresponding sensor.
If there is a malfunction in the speed sensor or the yaw rate and acceleration sensor (airbag ECU assembly), an abnormal value may be output although the steering angle sensor is normal.
If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these two sensors and inspect the steering angle sensor.
A
B
C
D
E
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the power switch off (lock).
Remove the steering wheel and the column cover.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the steering angle sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L51-5 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
| L51-6 (BAT) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Steering Angle Sensor) |
OK
NG
Turn the power switch off (lock).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L51-2 (ESS) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Steering Angle Sensor) |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
OK
NG