Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.12–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) D

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  DIAGNOSIS SYSTEM  


ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

ECM


ii.

Brake booster with master cylinder assembly (Skid control ECU)


iii.

Main body ECU (Multiplex network body ECU)


iv.

Power steering ECU assembly


v.

Certification ECU (Smart key ECU assembly)


vi.

Airbag ECU assembly


vii.

Spiral cable with sensor sub-assembly (Steering angle sensor)


viii.

Hybrid vehicle control ECU


ix.

Transmission control ECU assembly


x.

Combination meter sub-assembly


xi.

Radio and display receiver assembly*


xii.

Air conditioning amplifier assembly



b.

Sub bus 15

i.

Hybrid vehicle control ECU


ii.

ECM


iii.

Brake booster with master cylinder assembly (Skid control ECU)

HINT:

*: for Radio and Display Type





CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION


a.

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

ECU/Sensor Name GTS Display Applicability
ECM ECM (Engine) Installed on all vehicles
Hybrid vehicle control ECU Hybrid Vehicle Control Installed on all vehicles
Transmission control ECU assembly Transmission Control Installed on all vehicles
Power steering ECU assembly Power Steering (EPS) Installed on all vehicles
Brake booster with master cylinder assembly (Skid control ECU) Skid Control (ABS/VSC/TRAC) Installed on all vehicles
Spiral cable with sensor sub-assembly (Steering angle sensor) Spiral cable (Steering Angle Sensor) Installed on all vehicles
Airbag ECU assembly Airbag Installed on all vehicles
Main body ECU (Multiplex network body ECU) Main Body Installed on all vehicles
Certification ECU (Smart key ECU assembly) Certification (Smart) Installed on all vehicles
Air conditioning amplifier assembly Air Conditioning Amplifier Installed on all vehicles
Combination meter sub-assembly Combination Meter Installed on all vehicles
Radio and display receiver assembly Display and Navigation (AVN1) Vehicles with Radio and Display Type

HINT:

The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section.




CAN BUS CHECK


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.


a.

Using the GTS, select the CAN Bus Check screen.

NOTICE:
·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)

·

In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>SYSTEM DIAGRAM).



HINT:

Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, ''There is no system found on the Communication Bus'' will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main bus lines for a malfunction.




b.

Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

HINT:
·

If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.

·

If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.





HOW TO INTERPRET CAN BUS CHECK SCREEN


a.

When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

NOTICE:

The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.


HINT:
·

When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.

·

Wait for approximately 2 minutes after turning the power switch on (IG) (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.




b.

If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.

Example: Open in both CAN branch lines of ECU B on the V bus

C240692E12
5.875,0.083 6.135,0.344 0.26,0.26 10 false *a 0.396,3.219 1.063,3.604 0.667,0.385 10 false DLC3 5.875,0.542 6.135,0.802 0.26,0.26 10 false *b 5.479,1.031 5.74,1.292 0.26,0.26 10 false *c 5.479,1.552 5.74,1.813 0.26,0.26 10 false *d 5.573,2.073 5.833,2.333 0.26,0.26 10 false *e 4.292,3.083 4.552,3.344 0.26,0.26 10 false *f

Text in Illustration
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of Malfunction
*e Not displayed or background color changes to red or yellow *f CAN Bus Check Screen

HINT:

When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.



c.
C240693E14
0.24,1.698 0.479,1.896 0.24,0.198 10 false *a 2.885,2.427 3.125,2.625 0.24,0.198 10 false *b 1.031,2.438 1.271,2.635 0.24,0.198 10 false *c

If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor which is not displayed) is suspected.

Example: Open in a CAN branch line for ECU D on the V bus

Text in Illustration
*a Background color periodically changes to yellow or red
*b Not displayed or background color is yellow or red
*c Not displayed

Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, ''There is no system found on the Communication Bus'' will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.

·

The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.




d.
C240694E11
0.24,1.708 0.458,1.938 0.219,0.229 10 false *a 2.875,2.417 3.094,2.646 0.219,0.229 10 false *a

If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.

Example: Open in both CAN branch lines of ECU C on the V bus

Text in Illustration
*a Not displayed or background color changes to red

HINT:
·

In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.

·

If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.

·

The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.




e.
C240695E11
3,1.531 3.188,1.708 0.188,0.177 10 false *a

If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.

Example: Open in both CAN branch lines of ECU G on the sub bus

Text in Illustration
*a Background color changes to red

HINT:
·

A communication error in a sub bus does not affect the V bus or other buses.

·

When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)




f.

If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU A and B are not displayed or their background color changes to red.)

C240696E18
0.385,3.208 0.906,3.479 0.521,0.271 10 false DLC3 5.844,0.083 6.125,0.313 0.281,0.229 10 false *a 5.844,0.542 6.125,0.771 0.281,0.229 10 false *b 5.458,1.042 5.74,1.271 0.281,0.229 10 false *c 5.469,1.563 5.75,1.792 0.281,0.229 10 false *d 5.563,2.083 5.844,2.313 0.281,0.229 10 false *e 4.302,3.063 4.583,3.292 0.281,0.229 10 false *f

Text in Illustration
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of Malfunction
*e Not displayed or background color is red *f CAN Bus Check Screen

HINT:

If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



g.

If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU I and J are not displayed or their background color changes to red.)

C240697E15
0.375,3.229 0.813,3.448 0.438,0.219 10 false DLC3 5.854,0.094 6.146,0.385 0.292,0.292 10 false *a 5.583,2.094 5.865,2.323 0.281,0.229 10 false *e 5.854,0.542 6.135,0.771 0.281,0.229 10 false *b 5.49,1.052 5.771,1.281 0.281,0.229 10 false *c 5.49,1.583 5.771,1.813 0.281,0.229 10 false *d 4.323,3.073 4.604,3.302 0.281,0.229 10 false *f 2.719,1.458 3,1.688 0.281,0.229 10 false *g

Text in Illustration
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of Malfunction
*e Not displayed or background color is red *f CAN Bus Check Screen
*g Gateway Function Equipped ECU - -


h.
C240698E12
0.323,0.115 0.594,0.344 0.271,0.229 10 false *a 0.323,2.396 0.594,2.625 0.271,0.229 10 false *b 2.885,1.865 3.156,2.094 0.271,0.229 10 false *c 0.323,1.865 0.594,2.094 0.271,0.229 10 false *c 2.865,4.073 3.135,4.302 0.271,0.229 10 false *c

When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.

Text in Illustration
*a When any of the following malfunctions occur on the V bus
*b When any of the following malfunctions occur on a sub bus
*c Not displayed

Details of Malfunction
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and +B
Short between a CAN line (CANH or CANL) and ground
Open in a CAN main bus line

HINT:
·

When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).

·

When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.

·

A communication error in a sub bus does not affect the V bus or other buses.

·

The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.





HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)


a.

If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.

HINT:

Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.


i.

If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.

C240702E11
0.719,0.198 1.521,0.417 0.802,0.219 10 false Output from 2.198,0.198 3,0.417 0.802,0.219 10 false Output DTC 4.5,0.198 5.448,0.417 0.948,0.219 10 false Tester display 6.917,0.281 7.156,0.469 0.24,0.188 10 false : *a

Text in Illustration
*a Items to be Checked - -

NOTICE:
·

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.

·

Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)



HINT:

As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.



ii.

If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.

C240703E08
6.885,0.292 7.146,0.479 0.26,0.188 10 false : *a 4.448,0.198 5.365,0.417 0.917,0.219 10 false Tester display 2.198,0.198 3.052,0.396 0.854,0.198 10 false Output DTC 0.74,0.198 1.542,0.396 0.802,0.198 10 false Output from

Text in Illustration
*a Items to be Checked - -

NOTICE:

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.


HINT:
·

If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.

·

When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.





b.

To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.

C240704E14
3.594,0.333 3.802,0.333 false 1.365,1.823 1.052,2.323 1.052,2.323 0.885,2.323 false 4.865,0.323 5.146,0.521 0.281,0.198 10 false : *d 3.854,0.26 4.042,0.458 0.188,0.198 10 false *f 3.656,0.844 3.844,1.042 0.188,0.198 10 false *c 0.427,1.677 0.615,1.875 0.188,0.198 10 false *b 0.698,2.25 0.885,2.448 0.188,0.198 10 false *e 0.896,2.729 1.698,2.927 0.802,0.198 10 false Output from 2.479,2.729 3.281,2.927 0.802,0.198 10 false Output DTC 4.625,2.729 5.563,2.927 0.938,0.198 10 false Tester display 1.115,4.51 1.417,4.708 0.302,0.198 10 false : *a

Text in Illustration
*a Items to be Checked *b ECM
*c Gateway Function Equipped ECU *d Location of Malfunction
*e V Bus *f Sub Bus

NOTICE:

This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.


HINT:
·

As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.

·

When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.




c.

When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.

·

Short between CAN lines (CANH and CANL)

·

Short between a CAN line (CANH or CANL) and ground

·

Short between a CAN line (CANH or CANL) and +B

·

Open in a CAN branch line (CANH or CANL) of an ECU or sensor

·

Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor




DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.



a.

Hybrid Vehicle Control ECU / GTS Display "Hybrid Control"

Hybrid Vehicle Control ECU / GTS Display "Hybrid Control"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The hybrid vehicle control ECU does not receive data from the ECM for 0.68 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 1.68 seconds. HV system warning light turns on. DTC is stored until it is cleared using the GTS.
U0110*1 Lost Communication with Drive Motor Control Module ''A'' Either condition is met:
1.

The hybrid vehicle control ECU does not receive data from the MG ECU for 0.11 seconds or more.

2.

The hybrid vehicle control ECU does not send data to the MG ECU for 0.04 seconds or more.


Both conditions are met:
·

The power switch is on (IG) for 0.1 seconds or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 0.21 seconds. HV system warning light turns on. DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module The hybrid vehicle control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.34 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 2 seconds or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 4.34 seconds. HV system warning light turns on. DTC is stored until it is cleared using the GTS.
U0140 Communication Error from Body ECU to HV ECU The hybrid vehicle control ECU does not receive data from the main body ECU (multiplex network body ECU) for 3.6 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 4.6 seconds. HV system warning light turns on. DTC is stored until it is cleared using the GTS.
U0151 Communication Error from Airbag ECU to HV ECU The hybrid vehicle control ECU does not receive data from the airbag ECU assembly for 10.6 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 11.6 seconds. HV system warning light turns on. DTC is stored until it is cleared using the GTS.
U0164 Communication Error from A/C ECU to HV ECU The hybrid vehicle control ECU does not receive data from the air conditioning amplifier assembly for 10.6 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 11.6 seconds. - DTC is stored until it is cleared using the GTS.
U029A*2 Lost Communication with Hybrid Battery Pack Sensor Module The hybrid vehicle control ECU does not receive data from the battery smart unit for 0.52 seconds or more. The power switch is on (IG) for 0.5 seconds or more. Turn the power switch on (IG) and wait at least 1.02 seconds. HV system warning light turns on. DTC is stored until it is cleared using the GTS.
U0424*1 Invalid Data Received from HVAC Control Module The hybrid vehicle control ECU receives an abnormal operation value command from the air conditioning amplifier assembly for 3 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 4 seconds. - DTC is stored until it is cleared using the GTS.
U1107 Lost Communication with Power Management Module The hybrid vehicle control ECU does not receive data from the certification ECU (smart key ECU assembly) for 3.6 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


Turn the power switch on (IG) and wait at least 4.6 seconds. HV system warning light turns on. DTC is stored until it is cleared using the GTS.

HINT:
·

This ECU uses the CAN communication system for DTC communication.

·

The hybrid vehicle control ECU stores DTCs for the dynamic radar cruise control system.




b.

Hybrid Vehicle Control ECU / GTS Display "Cruise Control"

Hybrid Vehicle Control ECU / GTS Display "Cruise Control"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0122 Lost Communication with Vehicle Dynamic Control Module While the cruise control system is on (the system has been switched on using the ON/OFF button on the cruise control switch), the hybrid vehicle control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.73 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 2.1 seconds or more.

·

The power source voltage of the hybrid vehicle control ECU is 9.5 V or more.


After turning the power switch on (IG), turn the cruise control main switch on and wait for at least 4.83 seconds.
·

Cruise control indicator light (amber) illuminates.

·

Displays messages on the multi-information display.


DTC is stored until it is cleared using the GTS.

HINT:
·

This ECU uses the CAN communication system for DTC communication.

·

The hybrid vehicle control ECU stores DTCs for the cruise control system.




c.

ECM / GTS Display "Engine and ECT"

ECM / GTS Display "Engine and ECT"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0293 Lost Communication with HV ECU The ECM does not receive data from the hybrid vehicle control ECU for 0.576 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the power switch on (IG) and wait at least 1.576 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



d.

Transmission Control ECU Assembly / GTS Display "Transmission Control"

Transmission Control ECU Assembly / GTS Display "Transmission Control"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0146 Lost Communication with Body ECU The transmission control ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the transmission control ECU assembly is 10 V or more.


Turn the power switch on (IG) and wait at least 11 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



e.

Power Steering ECU Assembly / GTS Display "EMPS"

Power Steering ECU Assembly / GTS Display "EMPS"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0129 Lost Communication with Brake System Control Module The power steering ECU assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.3 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 2 seconds or more.

·

The power source voltage of the power steering ECU assembly is 9 V or more.


Turn the power switch on (IG) and wait at least 4.3 seconds. EPS warning light illuminates. DTC remains stored only while malfunction is occurring.
U0293 Lost Communication with Hybrid Control Module The power steering ECU assembly does not receive data from the hybrid vehicle control ECU for 2.3 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 2 seconds or more.

·

The power source voltage of the power steering ECU assembly is 9 V or more.


Turn the power switch on (IG) and wait at least 4.3 seconds. EPS warning light illuminates. DTC remains stored only while malfunction is occurring.

HINT:

This ECU uses the CAN communication system for DTC communication.



f.

Brake booster with master cylinder assembly (Skid control ECU) / GTS Display "ABS/VSC/TRC"

Brake booster with master cylinder assembly (Skid control ECU) / GTS Display "ABS/VSC/TRC"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Control Module Communication Bus OFF One of the following conditions is met:
1.

The brake booster with master cylinder assembly (skid control ECU) keeps sending data to an ECU or sensor for 5 seconds or more because a reception completion cannot be received.

2.

The airbag ECU assembly or spiral cable with sensor sub-assembly (steering angle sensor) and brake booster with master cylinder assembly (skid control ECU) cannot communicate for 1 second or more.

3.

The following condition occurs 10 times in succession within 60 seconds:

- The airbag ECU assembly or spiral cable with sensor sub-assembly (steering angle sensor) cannot communicate with the brake booster with master cylinder assembly (skid control ECU) once or more within 5 seconds.

4.

The following condition occurs 10 times in succession:

- The brake booster with master cylinder assembly (skid control ECU) cannot send/receive data (bus off) once or more within 0.1 seconds.


Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V.


Turn the power switch on (IG) and wait at least 60 seconds.
·

ABS warning light illuminates.

·

Brake warning light illuminates (yellow).

·

Slip warning light illuminates.


DTC is stored until it is cleared using the GTS.
U0120 Lost Communication with Starter / Generator Control Module The brake booster with master cylinder assembly (skid control ECU) does not receive data from the certification ECU (smart key ECU assembly) for 3 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V.


Turn the power switch on (IG) and wait at least 4 seconds. Brake warning light illuminates (yellow). DTC is stored until it is cleared using the GTS.
U0123 Lost Communication with Yaw Rate Sensor Module Either condition is met:
1.

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly for 1 second or more.

2.

The following condition occurs 10 times in succession within 60 seconds:

- The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly once or more within 5 seconds.


Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V.


Turn the power switch on (IG) and wait at least 60 seconds.
·

ABS warning light illuminates.

·

Brake warning light illuminates (yellow).

·

Slip warning light illuminates.


DTC is stored until it is cleared using the GTS.
U0124 Lost Communication with Lateral Acceleration Sensor Module Either condition is met:
1.

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly for 1 second or more.

2.

The following condition occurs 10 times in succession within 60 seconds:

- The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly once or more within 5 seconds.


Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V.


Turn the power switch on (IG) and wait at least 60 seconds.
·

ABS warning light illuminates.

·

Brake warning light illuminates (yellow).

·

Slip warning light illuminates.


DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Either condition is met:
1.

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the spiral cable with sensor sub-assembly (steering angle sensor) for 1 second or more.

2.

The following condition occurs 10 times in succession within 60 seconds:

- The brake booster with master cylinder assembly (skid control ECU) does not receive data from the spiral cable with sensor sub-assembly (steering angle sensor) once or more within 5 seconds.


Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V.


Turn the power switch on (IG) and wait at least 60 seconds. Slip warning light illuminates. DTC is stored until it is cleared using the GTS.
U0293 Communication Error from HV ECU Either condition is met:
1.

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU for 2 seconds or more.

2.

The following condition occurs 10 times in succession within 60 seconds:

- With the IG2 terminal voltage of the brake booster with master cylinder assembly (skid control ECU) at 9.5 V or more, the brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU once or more within 5 seconds.


Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V.


Turn the power switch on (IG) and wait at least 60 seconds.
·

Brake warning light illuminates (yellow).

·

Slip warning light illuminates.


DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



g.

Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) / GTS Display "-"

HINT:

The spiral cable with sensor sub-assembly (steering angle sensor) is connected to the CAN communication system, but the spiral cable with sensor sub-assembly (steering angle sensor) does not store or output CAN communication DTCs.



h.

Airbag ECU Assembly / GTS Display "SRS Airbag"

HINT:

The airbag ECU assembly is connected to the CAN communication system, but the airbag ECU assembly does not store or output CAN communication DTCs.



i.

Main Body ECU (Multiplex network body ECU) / GTS Display "Main Body"

Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/ PCM "A" The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0101 Lost Communication with TCM The main body ECU (multiplex network body ECU) does not receive data from the transmission control ECU assembly for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0120 Lost Communication with Starter / Generator Control Module The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module The main body ECU (multiplex network body ECU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module The main body ECU (multiplex network body ECU) does not receive data from the airbag ECU assembly for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster The main body ECU (multiplex network body ECU) does not receive data from the combination meter sub-assembly for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0164 Lost Communication with HVAC Control Module The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with Hybrid Powertrain Control Module The main body ECU (multiplex network body ECU) does not receive data from the hybrid vehicle control ECU for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0327 Software Incompatibility with Vehicle Security The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. Both conditions are met:
·

Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more.


Turn the power switch on (IG) and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



j.

Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"

Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0103 Lost Communication with Gear Shift Module "A" The certification ECU (smart key ECU assembly) does not receive data from the transmission control ECU assembly for 5 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.
U0129 Vehicle Speed Signal Communication The certification ECU (smart key ECU assembly) does not receive vehicle speed data from the brake booster with master cylinder assembly (skid control ECU) for 3 seconds or more Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Main Body ECU The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS.
U0293 HV ECU Communication The certification ECU (smart key ECU assembly) does not receive data from the hybrid vehicle control ECU for 3.1 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 3.1 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



k.

Certification ECU (Smart key ECU assembly) / GTS Display "Entry&Start"

Certification ECU (Smart key ECU assembly) / GTS Display "Entry&Start"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM / PCM "A" The certification ECU (smart key ECU assembly) does not receive data from the ECM for 10 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 11 seconds. - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 11 seconds. - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module The certification ECU (smart key ECU assembly) does not receive data from the combination meter sub-assembly for 10 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 11 seconds. - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with HV ECU The certification ECU (smart key ECU assembly) does not receive data from the hybrid vehicle control ECU for 10 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the power switch on (IG) and wait at least 11 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



l.

Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"

Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM / PCM ''A'' The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the air conditioning amplifier assembly is 8.5 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.
U0131 Lost Communication with Power Steering Control Module The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 5 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the air conditioning amplifier assembly is 8.5 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module ''B'' The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the air conditioning amplifier assembly is 8.5 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) The air conditioning amplifier assembly does not receive data from the combination meter sub-assembly for 5 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the air conditioning amplifier assembly is 8.5 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with HV ECU The air conditioning amplifier assembly does not receive data from the hybrid vehicle control ECU for 5 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the air conditioning amplifier assembly is 8.5 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



m.

Combination Meter Sub-assembly / GTS Display "Combination Meter"

Combination Meter Sub-assembly / GTS Display "Combination Meter"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM / PCM "A" The combination meter sub-assembly does not receive data from the hybrid vehicle control ECU for 2 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the combination meter sub-assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 2 seconds. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Skid Control ECU The combination meter sub-assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 3 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the combination meter sub-assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS.
U0131 Lost Communication with Power Steering Control Module The combination meter sub-assembly does not receive data from the power steering ECU assembly for 3 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the combination meter sub-assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" The combination meter sub-assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the combination meter sub-assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 10 seconds. - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Airbag ECU The combination meter sub-assembly does not receive data from the airbag ECU assembly for 10 seconds or more. Both conditions are met:
·

The power switch is on (IG).

·

The power source voltage of the combination meter sub-assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 10 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.



n.

Radio and Display Receiver Assembly / GTS Display "Navigation System"

Radio and Display Receiver Assembly / GTS Display "Navigation System"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Sending Malfunction (Navigation to APGS) The radio and display receiver assembly does not send/receive data for 5 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 6 seconds. - DTC is stored until it is cleared using the GTS.
U0100 Lost Communication with ECM / PCM "A" The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module The radio and display receiver assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1 second or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 2 seconds. - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 4 seconds. - DTC is stored until it is cleared using the GTS.
U0155 Meter ECU Communication The radio and display receiver assembly does not receive data from the combination meter sub-assembly for 30 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 31 seconds. - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with HV ECU The radio and display receiver assembly does not receive data from the hybrid vehicle control ECU for 4 seconds or more. Both conditions are met:
·

The power switch is on (IG) for 1 second or more.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or more.


Turn the power switch on (IG) and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.

HINT:

This ECU uses the CAN communication system for DTC communication.




DTC COMBINATION TABLE (OPEN OR SHORT IN V BUS, PAST COMMUNICATION ERROR)


a.

Regarding a past communication error of an ECU and sensor connected to the V bus (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN bus line(s) that had a malfunction can be determined based on the following DTC combination table.

HINT:
·

Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.

·

Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).

·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



for LHD
- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC Center Airbag Sensor Communication Stop Mode (See page (Click here)) Air Conditioning Amplifier Communication Stop Mode (See page (Click here)) Audio Receiver Assembly Communication Stop Mode (See page (Click here)) Main Body ECU Communication Stop Mode (See page (Click here))
V Bus Airbag ECU Assembly - - - - -
Air Conditioning Amplifier Assembly U0100 - ○ - -
U0131 - ○ - -
U0142 - ○ - ○
U0155 - ○ - -
U0293 - ○ - -
Radio and Display Receiver Assembly* U0100 - - ○ -
U0129 - - ○ -
U0140 - - ○ ○
U0155 - - ○ -
U0293 - - ○ -
Main Body ECU (Multiplex Network Body ECU) U0100 - - - ○
U0101 - - - ○
U0120 - - - ○
U0129 - - - ○
U0151 ○ - - ○
U0155 - - - ○
U0164 - ○ - ○
U0293 - - - ○
U0327 - - - ○
V Bus Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 - - - -
U0123 ○ - - -
U0124 ○ - - -
U0126 - - - -
U0293 - - - -
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 - - - -
U0129 - - - -
U0140 - - - ○
U0151 ○ - - -
U0164 - ○ - -
U1107 - - - -
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 - - - -
Power Steering ECU Assembly U0129 - - - -
U0293 - - - -
ECM U0293 - - - -
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 - - - -
U0142 - - - ○
U0155 - - - -
U0293 - - - -
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 - - - -
U0129 - - - -
U0140 - - - ○
U0293 - - - -
Combination Meter Sub-assembly U0100 - - - -
U0129 - - - -
U0131 - - - -
U0142 - - - ○
U0151 ○ - - -
Transmission Control ECU Assembly U0146 - - - ○
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - - -

for LHD
- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC Skid Control ECU Communication Stop Mode (See page (Click here)) Hybrid Vehicle Control ECU Communication Stop Mode (See page (Click here)) Power Steering ECU Communication Stop Mode (See page (Click here)) Certification ECU Communication Stop Mode (See page (Click here))
V Bus Airbag ECU Assembly - - - - -
Air Conditioning Amplifier Assembly U0100 - - - -
U0131 - - ○ -
U0142 - - - -
U0155 - - - -
U0293 - ○ - -
Radio and Display Receiver Assembly* U0100 - - - -
U0129 ○ - - -
U0140 - - - -
U0155 - - - -
U0293 - ○ - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - - -
U0101 - ○ - -
U0120 - - - ○
U0129 ○ - - -
U0151 - - - -
U0155 - - - -
U0164 - - - -
U0293 - ○ - -
U0327 - - - ○
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 ○ - - ○
U0123 ○ - - -
U0124 ○ - - -
U0126 ○ - - -
U0293 ○ ○ - -
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 - ○ - -
U0129 ○ ○ - -
U0140 - ○ - -
U0151 - ○ - -
U0164 - ○ - -
U1107 - ○ - ○
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 ○ ○ - -
Power Steering ECU Assembly U0129 ○ - ○ -
U0293 - ○ ○ -
ECM U0293 - ○ - -
V Bus Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 - - - ○
U0142 - - - ○
U0155 - - - ○
U0293 - ○ - ○
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 - - - ○
U0129 ○ - - ○
U0140 - - - ○
U0293 - ○ - ○
Combination Meter Sub-assembly U0100 - ○ - -
U0129 ○ - - -
U0131 - - ○ -
U0142 - - - -
U0151 - - - -
Transmission Control ECU Assembly U0146 - - - -
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - - -

for LHD
- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC Transmission Control ECU Communication Stop Mode (See page (Click here)) Steering Angle Sensor Communication Stop Mode (See page (Click here)) DLC3
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - - -
U0142 - - -
U0155 - - -
U0293 - - -
Radio and Display Receiver Assembly* U0100 - - -
U0129 - - -
U0140 - - -
U0155 - - -
U0293 - - -
V Bus Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 - - -
U0129 - - -
U0151 - - -
U0155 - - -
U0164 - - -
U0293 - - -
U0327 - - -
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 - - -
U0123 - - -
U0124 - - -
U0126 - ○ -
U0293 - - -
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 - - -
U0129 - - -
U0140 - - -
U0151 - - -
U0164 - - -
U1107 - - -
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 - - -
Power Steering ECU Assembly U0129 - - -
U0293 - - -
ECM U0293 - - -
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 - - -
U0142 - - -
U0155 - - -
U0293 - - -
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 ○ - -
U0129 - - -
U0140 - - -
U0293 - - -
Combination Meter Sub-assembly U0100 - - -
U0129 - - -
U0131 - - -
U0142 - - -
U0151 - - -
Transmission Control ECU Assembly U0146 ○ - -
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



for LHD
- Trouble Mode (Open in Both CAN Main Bus Lines)
V Bus
Output ECU Output DTC ECM Communication Stop Mode (See page (Click here)) CAN No. 1 Junction Connector to CAN No. 2 Junction Connector CAN No. 2 Junction Connector to CAN No. 3 Junction Connector Combination Meter ECU Communication Stop Mode (See page (Click here))
V Bus Airbag ECU Assembly - - - - -
Air Conditioning Amplifier Assembly U0100 ○ ○ - -
U0131 - - - -
U0142 - ○ - -
U0155 - - ○ ○
U0293 - - ○ -
Radio and Display Receiver Assembly* U0100 ○ ○ - -
U0129 - ○ - -
U0140 - ○ - -
U0155 - - ○ ○
U0293 - - ○ -
Main Body ECU (Multiplex Network Body ECU) U0100 ○ - - -
U0101 - ○ ○ -
U0120 - ○ - -
U0129 - - - -
U0151 - ○ - -
U0155 - ○ ○ ○
U0164 - ○ - -
U0293 - ○ ○ -
U0327 - ○ - -
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 - ○ - -
U0123 - ○ - -
U0124 - ○ - -
U0126 - ○ - -
U0293 - ○ ○ -
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 ○ ○ ○ -
U0129 - ○ ○ -
U0140 - ○ ○ -
U0151 - - ○ -
U0164 - - ○ -
U1107 - - ○ -
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 - ○ ○ -
V Bus Power Steering ECU Assembly U0129 - ○ - -
U0293 - - ○ -
ECM U0293 ○ ○ ○ -
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 ○ ○ - -
U0142 - ○ - -
U0155 - - ○ ○
U0293 - - ○ -
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 - - ○ -
U0129 - ○ - -
U0140 - ○ - -
U0293 - - ○ -
Combination Meter Sub-assembly U0100 - - - ○
U0129 - ○ ○ ○
U0131 - - ○ ○
U0142 - ○ ○ ○
U0151 - - ○ ○
Transmission Control ECU Assembly U0146 - ○ ○ -
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



for LHD
- Trouble Mode (CAN Bus Line Short Circuit or Short to GND)
V Bus
Output ECU Output DTC CANH to CANL CANH to Ground Short CANL to Ground Short
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ○ ○ ○
U0131 ○ ○ ○
U0142 ○ ○ ○
U0155 ○ ○ ○
U0293 ○ ○ ○
Radio and Display Receiver Assembly* U0100 ○ ○ ○
U0129 ○ ○ ○
U0140 ○ ○ ○
U0155 ○ ○ ○
U0293 ○ ○ ○
V Bus Main Body ECU (Multiplex Network Body ECU) U0100 ○ ○ ○
U0101 ○ ○ ○
U0120 ○ ○ ○
U0129 ○ ○ ○
U0151 ○ ○ ○
U0155 ○ ○ ○
U0164 ○ ○ ○
U0293 ○ ○ ○
U0327 ○ ○ ○
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 ○ ○ ○
U0123 ○ ○ ○
U0124 ○ ○ ○
U0126 ○ ○ ○
U0293 ○ ○ ○
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 ○ ○ ○
U0129 ○ ○ ○
U0140 ○ ○ ○
U0151 ○ ○ ○
U0164 ○ ○ ○
U1107 ○ ○ ○
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 ○ ○ ○
Power Steering ECU Assembly U0129 ○ ○ ○
U0293 ○ ○ ○
ECM U0293 ○ ○ ○
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 ○ ○ ○
U0142 ○ ○ ○
U0155 ○ ○ ○
U0293 ○ ○ ○
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 ○ ○ ○
U0129 ○ ○ ○
U0140 ○ ○ ○
U0293 ○ ○ ○
Combination Meter Sub-assembly U0100 ○ ○ ○
U0129 ○ ○ ○
U0131 ○ ○ ○
U0142 ○ ○ ○
U0151 ○ ○ ○
Transmission Control ECU Assembly U0146 ○ ○ ○
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



for RHD
- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC Center Airbag Sensor Communication Stop Mode (See page (Click here)) Air Conditioning Amplifier Communication Stop Mode (See page (Click here)) Main Body ECU Communication Stop Mode (See page (Click here))
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - ○ -
U0131 - ○ -
U0142 - ○ ○
U0155 - ○ -
U0293 - ○ -
Main Body ECU (Multiplex Network Body ECU) U0100 - - ○
U0101 - - ○
U0120 - - ○
U0129 - - ○
U0151 ○ - ○
U0155 - - ○
U0164 - ○ ○
U0293 - - ○
U0327 - - ○
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 - - -
U0123 ○ - -
U0124 ○ - -
U0126 - - -
U0293 - - -
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 - - -
U0129 - - -
U0140 - - ○
U0151 ○ - -
U0164 - ○ -
U1107 - - -
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 - - -
Power Steering ECU Assembly U0129 - - -
U0293 - - -
ECM U0293 - - -
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 - - -
U0142 - - ○
U0155 - - -
U0293 - - -
V Bus Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 - - -
U0129 - - -
U0140 - - ○
U0293 - - -
Combination Meter Sub-assembly U0100 - - -
U0129 - - -
U0131 - - -
U0142 - - ○
U0151 ○ - -
Transmission Control ECU Assembly U0146 - - ○
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - -

for RHD
- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC Skid Control ECU Communication Stop Mode (See page (Click here)) Power Steering ECU Communication Stop Mode (See page (Click here)) Certification ECU Communication Stop Mode (See page (Click here))
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - ○ -
U0142 - - -
U0155 - - -
U0293 - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 - - ○
U0129 ○ - -
U0151 - - -
U0155 - - -
U0164 - - -
U0293 - - -
U0327 - - ○
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 ○ - ○
U0123 ○ - -
U0124 ○ - -
U0126 ○ - -
U0293 ○ - -
V Bus Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 - - -
U0129 ○ - -
U0140 - - -
U0151 - - -
U0164 - - -
U1107 - - ○
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 ○ - -
Power Steering ECU Assembly U0129 ○ ○ -
U0293 - ○ -
ECM U0293 - - -
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 - - ○
U0142 - - ○
U0155 - - ○
U0293 - - ○
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 - - ○
U0129 ○ - ○
U0140 - - ○
U0293 - - ○
Combination Meter Sub-assembly U0100 - - -
U0129 ○ - -
U0131 - ○ -
U0142 - - -
U0151 - - -
Transmission Control ECU Assembly U0146 - - -
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - -

for RHD
- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC Transmission Control ECU Communication Stop Mode (See page (Click here)) Hybrid Vehicle Control ECU Communication Stop Mode (See page (Click here)) Steering Angle Sensor Communication Stop Mode (See page (Click here)) DLC3
V Bus Airbag ECU Assembly - - - - -
V Bus Air Conditioning Amplifier Assembly U0100 - - - -
U0131 - - - -
U0142 - - - -
U0155 - - - -
U0293 - ○ - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - - -
U0101 - ○ - -
U0120 - - - -
U0129 - - - -
U0151 - - - -
U0155 - - - -
U0164 - - - -
U0293 - ○ - -
U0327 - - - -
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 - - - -
U0123 - - - -
U0124 - - - -
U0126 - - ○ -
U0293 - ○ - -
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 - ○ - -
U0129 - ○ - -
U0140 - ○ - -
U0151 - ○ - -
U0164 - ○ - -
U1107 - ○ - -
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 - ○ - -
Power Steering ECU Assembly U0129 - - - -
U0293 - ○ - -
ECM U0293 - ○ - -
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 - - - -
U0142 - - - -
U0155 - - - -
U0293 - ○ - -
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 ○ - - -
U0129 - - - -
U0140 - - - -
U0293 - ○ - -
Combination Meter Sub-assembly U0100 - ○ - -
U0129 - - - -
U0131 - - - -
U0142 - - - -
U0151 - - - -
Transmission Control ECU Assembly U0146 ○ - - -
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



for RHD
- Trouble Mode (Open in Both CAN Main Bus Lines)
V Bus
Output ECU Output DTC ECM Communication Stop Mode (See page (Click here)) CAN No. 1 Junction Connector to CAN No. 2 Junction Connector CAN No. 2 Junction Connector to CAN No. 3 Junction Connector Combination Meter ECU Communication Stop Mode (See page (Click here))
V Bus Airbag ECU Assembly - - - - -
Air Conditioning Amplifier Assembly U0100 ○ ○ - -
U0131 - - - -
U0142 - ○ - -
U0155 - - ○ ○
U0293 - ○ - -
Main Body ECU (Multiplex Network Body ECU) U0100 ○ - - -
U0101 - - - -
U0120 - ○ - -
U0129 - ○ ○ -
U0151 - ○ - -
U0155 - ○ ○ ○
U0164 - ○ - -
U0293 - - - -
U0327 - ○ - -
Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 - - ○ -
U0123 - - ○ -
U0124 - - ○ -
U0126 - - ○ -
U0293 - ○ ○ -
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 ○ - - -
U0129 - ○ ○ -
U0140 - - - -
U0151 - ○ - -
U0164 - ○ - -
U1107 - ○ - -
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 - ○ ○ -
V Bus Power Steering ECU Assembly U0129 - - ○ -
U0293 - ○ - -
ECM U0293 ○ - - -
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 ○ ○ - -
U0142 - ○ - -
U0155 - - ○ ○
U0293 - ○ - -
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 - ○ - -
U0129 - - ○ -
U0140 - ○ - -
U0293 - ○ - -
Combination Meter Sub-assembly U0100 - ○ ○ ○
U0129 - - - ○
U0131 - - ○ ○
U0142 - ○ ○ ○
U0151 - - ○ ○
Transmission Control ECU Assembly U0146 - - - -
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



for RHD
- Trouble Mode (CAN Bus Line Short Circuit or Short to GND)
V Bus
Output ECU Output DTC CANH to CANL CANH to Ground Short CANL to Ground Short
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ○ ○ ○
U0131 ○ ○ ○
U0142 ○ ○ ○
U0155 ○ ○ ○
U0293 ○ ○ ○
Main Body ECU (Multiplex Network Body ECU) U0100 ○ ○ ○
U0101 ○ ○ ○
U0120 ○ ○ ○
U0129 ○ ○ ○
U0151 ○ ○ ○
U0155 ○ ○ ○
U0164 ○ ○ ○
U0293 ○ ○ ○
U0327 ○ ○ ○
V Bus Brake Booster with Master Cylinder Assembly (Skid Control ECU)* U0120 ○ ○ ○
U0123 ○ ○ ○
U0124 ○ ○ ○
U0126 ○ ○ ○
U0293 ○ ○ ○
Hybrid Vehicle Control ECU
(Hybrid Control)
U0100 ○ ○ ○
U0129 ○ ○ ○
U0140 ○ ○ ○
U0151 ○ ○ ○
U0164 ○ ○ ○
U1107 ○ ○ ○
Hybrid Vehicle Control ECU
(Cruise Control)
U0122 ○ ○ ○
Power Steering ECU Assembly U0129 ○ ○ ○
U0293 ○ ○ ○
ECM U0293 ○ ○ ○
Certification ECU (Smart Key ECU Assembly)
(Entry Function)
U0100 ○ ○ ○
U0142 ○ ○ ○
U0155 ○ ○ ○
U0293 ○ ○ ○
Certification ECU (Smart Key ECU Assembly)
(Power Source Switching Function)
U0103 ○ ○ ○
U0129 ○ ○ ○
U0140 ○ ○ ○
U0293 ○ ○ ○
Combination Meter Sub-assembly U0100 ○ ○ ○
U0129 ○ ○ ○
U0131 ○ ○ ○
U0142 ○ ○ ○
U0151 ○ ○ ○
Transmission Control ECU Assembly U0146 ○ ○ ○
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.





CAN BUS WAVEFORMS


C230845E28
4.823,0.219 4.719,0.219 4.719,0.219 4.417,0.896 false 4.458,0.875 4.406,0.917 4.406,0.917 4.406,0.865 false 6.625,3.729 5.708,2.625 false 5.729,2.729 5.708,2.625 5.708,2.625 5.781,2.635 false 4.073,3.698 5.073,2.552 false 5.073,2.646 5.083,2.531 5.083,2.531 4.99,2.552 false 2.24,0.688 2.521,0.146 2.521,0.146 2.635,0.146 false 4.271,4.469 5.156,4.469 false 5.156,4.469 5.51,3.677 false 5.281,3.104 5.844,3.406 0.563,0.302 10 false ECU 3.365,3.156 3.927,3.458 0.563,0.302 10 false ECU 1.698,3.146 2.26,3.448 0.563,0.302 10 false DLC3 1.438,4.771 3.427,5.031 1.99,0.26 10 false : CAN Main Bus Line (CANH) 1.448,5.208 3.438,5.469 1.99,0.26 10 false : CAN Main Bus Line (CANL) 1.448,5.781 3.365,6.01 1.917,0.229 10 false : CAN Branch Line (CANH) 1.448,6.229 3.365,6.49 1.917,0.26 10 false : CAN Branch Line (CANL) 3.458,4.385 4.427,4.677 0.969,0.292 10 false CAN Branch 2.521,3.74 4.844,4.01 2.323,0.271 10 false Open in CAN Branch Line (CANL) 5.792,3.813 7.094,4.25 1.302,0.438 10 false Open in CAN Branch Line (CANH) 4.854,0.135 7.104,0.417 2.25,0.281 10 false Open in CAN Main Bus Line (CANH) 2.677,0.073 3.771,0.323 1.094,0.25 10 false CAN Main Bus

HINT:
·

The following waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN Bus Check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING). If no problems are found, check the following waveforms.

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
U113995E20
0.927,0.792 0.563,0.323 false 0.927,1.167 0.469,1.438 false 2.698,0.26 3.26,0.458 0.563,0.198 10 false 1 V/DIV. 2.938,1.365 3.333,1.563 0.396,0.198 10 false GND 1.26,1.917 2.208,2.125 0.948,0.208 10 false 50 μs./DIV. 0.052,0.208 0.531,0.375 0.479,0.167 10 false CANH 0.052,1.469 0.479,1.635 0.427,0.167 10 false CANL

Normal waveform


ii.
U114097E19
2.042,0.771 1.417,0.563 false 2.031,1.083 1.573,1.385 false 2.729,0.26 3.292,0.458 0.563,0.198 10 false 1 V/DIV. 2.958,1.375 3.354,1.573 0.396,0.198 10 false GND 1.271,1.885 2.219,2.094 0.948,0.208 10 false 50 μs./DIV. 0.99,0.438 1.469,0.604 0.479,0.167 10 false CANH 1.063,1.302 1.49,1.469 0.427,0.167 10 false CANL

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
U113999E20
0.99,0.938 0.5,0.417 false 0.896,0.979 0.5,1.448 false 2.729,0.24 3.292,0.438 0.563,0.198 10 false 1 V/DIV. 2.927,1.375 3.323,1.573 0.396,0.198 10 false GND 1.26,1.885 2.208,2.094 0.948,0.208 10 false 50 μs./DIV. 0.073,0.323 0.552,0.49 0.479,0.167 10 false CANH 0.073,1.479 0.5,1.646 0.427,0.167 10 false CANL

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
U114000E20
0.948,0.771 0.573,0.365 false 0.865,1.198 0.469,1.479 false 2.698,0.208 3.26,0.406 0.563,0.198 10 false 1 V/DIV. 2.938,1.365 3.333,1.563 0.396,0.198 10 false GND 1.271,1.896 2.219,2.104 0.948,0.208 10 false 50 μs./DIV. 0.073,0.24 0.552,0.406 0.479,0.167 10 false CANH 0.083,1.5 0.51,1.667 0.427,0.167 10 false CANL

Open in a CAN branch line (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




ii.
U114001E20
0.844,0.74 0.5,0.333 false 0.927,1.135 0.5,1.49 false 2.698,0.208 3.26,0.406 0.563,0.198 10 false 1 V/DIV. 2.938,1.354 3.333,1.552 0.396,0.198 10 false GND 1.271,1.896 2.219,2.104 0.948,0.208 10 false 50 μs./DIV. 0.073,0.198 0.552,0.365 0.479,0.167 10 false CANH 0.083,1.458 0.51,1.625 0.427,0.167 10 false CANL

Open in a CAN branch line (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




iii.
U113996E20
0.938,0.771 0.49,0.385 false 0.969,1.146 0.479,1.396 false 2.708,0.177 3.271,0.375 0.563,0.198 10 false 1 V/DIV. 2.948,1.344 3.344,1.542 0.396,0.198 10 false GND 1.271,1.896 2.219,2.104 0.948,0.208 10 false 50 μs./DIV. 0.083,0.302 0.563,0.469 0.479,0.167 10 false CANH 0.094,1.344 0.521,1.51 0.427,0.167 10 false CANL

Open in a CAN main bus line (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.

·

An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
U113997E20
1,1.344 0.563,0.75 false 1.094,1.542 0.552,1.844 false 2.688,0.188 3.25,0.385 0.563,0.198 10 false 1 V/DIV. 2.927,1.375 3.323,1.573 0.396,0.198 10 false GND 1.26,1.927 2.208,2.135 0.948,0.208 10 false 50 μs./DIV. 0.083,0.656 0.563,0.823 0.479,0.167 10 false CANH 0.073,1.781 0.5,1.948 0.427,0.167 10 false CANL

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
U113998E20
1.031,0.708 0.5,0.25 false 1.042,1.396 0.5,1.75 false 2.708,0.208 3.271,0.406 0.563,0.198 10 false 1 V/DIV. 2.948,1.354 3.344,1.552 0.396,0.198 10 false GND 1.26,1.906 2.208,2.115 0.948,0.208 10 false 50 μs./DIV. 0.083,0.115 0.563,0.281 0.479,0.167 10 false CANH 0.083,1.656 0.51,1.823 0.427,0.167 10 false CANL

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

HINT:

If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.

Data content Data Detected and Sent by Data Received by
(Can be Checked in the Data List)
Data Received by
(Cannot be Checked in the Data List)
Relevant Data List Item
[Selected System]
Accelerator position Hybrid Vehicle Control ECU - Radio and display receiver assembly Accelerator Degree [Hybrid Control]
Engine speed ECM Hybrid Vehicle Control ECU
·

Airbag ECU assembly

·

Main body ECU (Multiplex network body ECU)

·

Combination meter sub-assembly

·

Radio and display receiver assembly


·

Engine Speed [Engine and ECT]

·

Engine Revolution [Hybrid Control]


Engine coolant temp ECM Combination meter sub-assembly -
·

Coolant Temp [Engine and ECT]

·

Coolant Temperature [Combination Meter]


Vehicle speed Brake booster with master cylinder assembly (Skid control ECU)
·

Hybrid Vehicle Control ECU

·

Certification ECU (Smart key ECU assembly)

·

Power steering ECU assembly

·

Combination meter sub-assembly


·

Transmission control ECU assembly

·

Airbag ECU assembly


·

Vehicle Speed [ABS/VSC/TRC]

·

Vehicle Spd [Hybrid Control]

·

Vehicle Speed Signal [Power Source Control]

·

Meter Vehicle Velocity [EMPS]

·

Vehicle Speed Meter [Combination Meter]


Combination meter sub-assembly*3 -
·

Air conditioning amplifier assembly

·

Main body ECU (Multiplex network body ECU)

·

Certification ECU (Smart key ECU assembly)


Vehicle Speed Meter [Combination Meter]
Wheel speed Brake booster with master cylinder assembly (Skid control ECU) -
·

Airbag ECU assembly

·

Hybrid Vehicle Control ECU

·

Power steering ECU assembly


·

FR Wheel Speed [ABS/VSC/TRC]

·

FL Wheel Speed [ABS/VSC/TRC]

·

RR Wheel Speed [ABS/VSC/TRC]

·

RL Wheel Speed [ABS/VSC/TRC]


Park (P) state signal Transmission control ECU assembly Certification ECU (Smart key ECU assembly) Combination meter sub-assembly*2
·

Shift Pos Display (P) [Transmission Control]

·

Shift P Signal Pulse [Power Source Control]


Ambient temperature Air conditioning amplifier assembly -
·

Main body ECU (Multiplex network body ECU)

·

Radio and display receiver assembly


Ambient Temp Sensor [Air Conditioner]
Driver door courtesy Main body ECU (Multiplex network body ECU) -
·

Hybrid Vehicle Control ECU

·

Certification ECU (Smart key ECU assembly)

·

Combination meter sub-assembly*2

·

Radio and display receiver assembly


FL Door Courtesy SW [Main Body]
Steering angle sensor Spiral cable with sensor sub-assembly (Steering angle sensor)
·

Brake booster with master cylinder assembly (Skid control ECU)

·

Power steering ECU assembly


·

Airbag ECU assembly

·

Hybrid Vehicle Control ECU

·

Radio and display receiver assembly


·

Steering Angle Sensor [ABS/VSC/TRC]

·

Steering Angle Velocity [EMPS]


Yaw rate sensor Airbag ECU assembly Brake booster with master cylinder assembly (Skid control ECU)
·

Airbag ECU assembly

·

Power steering ECU assembly


·

Yaw Rate Sensor [ABS/VSC/TRC]

·

Yaw Rate Sensor2 [ABS/VSC/TRC]


Deceleration sensor Airbag ECU assembly Brake booster with master cylinder assembly (Skid control ECU)
·

Airbag ECU assembly

·

Hybrid Vehicle Control ECU

·

Power steering ECU assembly


·

Deceleration Sensor [ABS/VSC/TRC]

·

Deceleration Sensor2 [ABS/VSC/TRC]


Hybrid Vehicle Control ECU power supply condition Hybrid Vehicle Control ECU*1 - - +B [Hybrid Control]
Certification ECU (Smart key ECU assembly) power supply condition Certification ECU (Smart key ECU assembly)*1 - - Power Supply Condition [Power Source Control]
ECM power supply condition ECM*1 - - Battery Voltage [Engine and ECT]
Brake pedal stroke sensor Brake booster with master cylinder assembly (Skid control ECU)*1 - -
·

Stroke Sensor [ABS/VSC/TRC]

·

Stroke Sensor2 [ABS/VSC/TRC]


Power steering ECU assembly power supply condition Power steering ECU assembly*1 - - IG Power Supply [EMPS]
Transmission control ECU assembly power supply condition Transmission control ECU assembly*1 - - IG (+B) Voltage Value [Transmission Control]
Intensity of light received by the solar sensor Air conditioning amplifier assembly*1 - - Solar Sensor (D Side) [Air Conditioner]
Combination meter sub-assembly power supply condition Combination meter sub-assembly*1 - - +B Voltage Value [Combination Meter]
Driver door touch sensor Certification ECU (Smart key ECU assembly)*1 - - D-Door Touch Sensor [Entry&Start]


*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.

*2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter.

*3: The combination meter sub-assembly receives a vehicle speed signal from the brake actuator assembly (skid control ECU) and sends the signal to other ECUs.


b.

Details of relevant Data List items (Selected system: Hybrid Control )

NOTICE:
·

Some Data List values may vary significantly if there are slight differences in the environment in which the vehicle is operating when measurements are obtained. Variations may also occur due to aging of the vehicle. Due to these considerations, it is not always possible to provide definite values to be used for judgment of malfunctions. It is possible that a malfunction may be present even if measured values are within the reference range.

·

In the event of a problem with intricate symptoms, collect sample data from another vehicle of the same model operating under identical conditions in order to reach an overall judgment by comparing all the items in the Data List.



i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Enter the following menus: Powertrain / Hybrid Control / Data List.


iv.

Read the Data List according to the display on the GTS.

Hybrid Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Revolution Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
While idling after the engine warmed up and inspection mode:
Approximately 900 rpm
While driving at a constant speed:
No significant fluctuation
-
Vehicle Spd Vehicle speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Vehicle stopped:
0 km/h (0 mph)
While driving at a constant speed:
No significant fluctuation
-
+B Auxiliary battery voltage/
Min.: 0.00 V, Max.: 65.53 V
Constant:
Auxiliary battery voltage 10.00 to 15.00 V
Auxiliary battery
Accelerator Degree Accelerator pedal depressed angle/
Min.: 0.0%, Max.: 127.5%
Accelerator pedal depressed:
Changes with accelerator pedal pressure
Accelerator pedal sensor assembly

HINT:

When reviewing Data List information, try to select only the specific Data List items related to the inspection being performed. If all items are selected when checking the Data List, the interval between updates for each item will be longer, resulting in delayed or incorrect data.




c.

Details of relevant Data List items (Selected system: Engine and ECT)

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Warm up the engine.


ii.

Turn the A/C switch off.


iii.

Turn the power switch off.


iv.

Connect the GTS to the DLC3.


v.

Turn the power switch on (IG).


vi.

Turn the GTS on.


vii.

Enter the following menus: Powertrain / Engine and ECT / Data List.


viii.

Read the Data List according to the display on the GTS.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
950 to 1050 rpm: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Coolant Temp Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up Diagnostic Note:
This is the engine coolant temperature.
HINT:
·

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit may be open or shorted.

·

Check if the engine overheats when the value indicates 140°C (284°F).



Battery Voltage Auxiliary battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 16 V: Power switch on (IG) Diagnostic Note:
If 11 V or less, characteristics of some electrical components may change.



d.

Details of relevant Data List items (Selected system: Air Conditioner)

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Turn the power switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


vi.

Read the Data List according to the display on the GTS.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temp Sensor Ambient temperature sensor (thermistor assembly) /
Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Solar Sensor (D Side) Solar sensor (automatic light control sensor) /
Min.: 0
Max.: 255
Solar sensor value increases as brightness increases -



e.

Details of relevant Data List items (Selected system: Combination Meter)

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Warm up the engine.


ii.

Turn the power switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the power switch on (IG).


v.

Turn the GTS on.


vi.

Enter the following menus: Body Electrical / Combination Meter / Data List.


vii.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed /
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Almost the same as actual vehicle speed -
Coolant Temperature Engine coolant temperature /
0 to 127.5°C (0 to 261.5°F)
After warming up:
75 to 100°C (167 to 212°F)
-
+B Voltage Value Auxiliary battery voltage /
Min.: 0 V, Max.: 25.5 V
11 to 14 V -



f.

Details of relevant Data List items (Selected system: Power Source Control)

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle moving or stationary/Stop or Run Stop: Vehicle stopped
Run: Vehicle moving at 5 km/h (3 mph) or more
-
Shift P Signal Pulse Status of the shift P signal pulse/Normal1, Normal2, Normal3, Unknown, Error1, Error2 or Error3 Normal1: Signal normal and park (P) state cannot be determined
Normal2: Signal normal and park (P) selected
Normal3: Signal normal and R, N, D or B selected
Unknown: Other
Error1: Signal abnormal and park (P) state cannot be determined
Error2: Signal abnormal and park (P) selected
Error3: Signal abnormal and R, N, D or B selected
Use this item to determine if the P position signal is malfunctioning.
Power Supply Condition State of power supply/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON All OFF: Power switch off (power supply off)
ACC ON: Power switch on (ACC) (ACC relay on)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Starting hybrid control system
Since "IG1 ON" and "IG2 ON" turn "on" at approximately the same time, "IG1 ON" may not be displayed ("IG1 ON" turns on for a very short time).



g.

Details of relevant Data List items (Selected system: ABS/VSC/TRC)

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Warm up the engine.


ii.

Turn the power switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the power switch on (IG).


v.

Turn the GTS on.


vi.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


vii.

Read the Data List according to the display on the GTS.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor /
Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor 2 /
Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Deceleration Sensor Acceleration sensor 1 /
Min.: -18.525 m/s2, Max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Deceleration Sensor2 Acceleration sensor 2 /
Min.: -18.525 m/s2, Max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Yaw Rate Sensor Yaw rate sensor 1 / Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Right turn: -128 to 0 degrees/s
Left turn: 0 to 127 degrees/s
-
Yaw Rate Sensor2 Yaw rate sensor 2 / Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Right turn: -128 to 0 degrees/s
Left turn: 0 to 127 degrees/s
-
Steering Angle Sensor Steering angle sensor /
Min.: -3276.8 degrees, Max.: 3276.7 degrees
Left turn: Increase
Right turn: Decrease
-
FR Wheel Speed Front speed sensor RH /
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH /
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH /
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH /
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor /
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations



h.

Details of relevant Data List items (Selected system: EMPS)

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Turn the power switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / EMPS / Data List.


vi.

Read the Data List according to the display on the GTS.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from meter/
Min.: 0.0 km/h (0.0 mph)
Max.: 300.0 km/h (186.4 mph)
0 km/h (0 mph) Power switch on (READY) and vehicle stopped
No significant fluctuation Power switch on (READY) and vehicle driven at a constant speed
Steering Angle Velocity Steering angle speed/
Min.: -32768 deg/s
Max.: 32767 deg/s
Value changes in proportion to steering speed
- The value rises in left turn
- The value descends in right turn
Power switch on (READY) and steering wheel being turned
IG Power Supply IG power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Power switch on (IG)



i.

Details of relevant Data List items (Selected system: Transmission Control)

NOTICE:
·

Some Data List values may vary significantly if there are slight differences in the environment in which the vehicle is operating when measurements are obtained. Variations may also occur due to aging of the vehicle. Due to these considerations, it is not always possible to provide definite values to be used for judgment of malfunctions. It is possible that a malfunction may be present even if measured values are within the reference range.

·

In the event of a problem with intricate symptoms, collect sample data from another vehicle of the same model operating under identical conditions in order to reach an overall judgment by comparing all the items in the Data List.



HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Warm up the engine.


ii.

Turn the power switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the power switch on (IG).


v.

Turn the GTS on.


vi.

Enter the following menus: Body Electrical / Transmission Control / Data List.


vii.

Read the Data List according to the display on the GTS.

Transmission Control
Tester Display Measurement Item/Range Normal Condition Normal Condition
Shift Pos Display (P) Shift position display (P) / ON or OFF ON: Park (P) selected
OFF: A shift state other than park (P) selected (When normal) (May go off during malfunction)
-
IG (+B) Voltage Value IG (+B) voltage value / Min: 0.00 V, Max: 19.00 V 8.00 to 16.00 V: On (IG) +B signal circuit



j.

Details of relevant Data List items (Selected system: Main Body)

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Main Body / Data List.


v.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch LH signal/ON or OFF ON: Front door LH closed
OFF: Front door LH open
-



k.

Details of relevant Data List items (Selected system: Entry&Start)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:
·

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

When using the GTS with the power switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Entry&Start / Data List.


v.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D-Door Touch Sensor Driver door touch sensor (unlock sensor)* / ON or OFF ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.



*: Data from an actual vehicle provided for reference.