Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2017.12–2020.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1249  Open Circuit in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the brake pedal operation status.

The skid control ECU has an open detection circuit, which outputs this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code INF Code DTC Detection Condition Trouble Area
C1249 231 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.
·

Wire harness or connector

·

Stop light switch

·

Brake booster with master cylinder (Skid control ECU)



WIRING DIAGRAM

C314351E15
1.406,0.927 1.563,1.125 0.156,0.198 10 false 1 1.75,0.938 1.958,1.167 0.208,0.229 10 false 2 1.969,0.833 2.292,1.073 0.323,0.24 10 false 7*1 2.375,0.823 2.667,1.063 0.292,0.24 10 false 1*2 1.938,1.031 2.24,1.26 0.302,0.229 10 false A79 2.354,1.021 2.677,1.281 0.323,0.26 10 false A80 1.958,1.75 2.219,1.979 0.26,0.229 10 false 2*1 2.365,1.75 2.594,1.948 0.229,0.198 10 false 3*2 1.948,1.958 2.229,2.229 0.281,0.271 10 false A79 2.365,1.958 2.677,2.219 0.313,0.26 10 false A80 2.74,1.021 2.948,1.25 0.208,0.229 10 false B 2.74,1.969 3.146,2.25 0.406,0.281 10 false GND 2.802,0.719 3.396,1.01 0.594,0.292 10 false ACC*1 3.021,1.354 3.458,1.677 0.438,0.323 10 false L*1 2.948,2.583 3.521,2.896 0.573,0.313 10 false OUT 3.375,0.521 3.708,0.75 0.333,0.229 10 false 4*1 3.354,0.719 3.75,0.969 0.396,0.25 10 false A79 3.385,1.146 3.677,1.385 0.292,0.24 10 false 3*1 3.354,1.344 3.729,1.615 0.375,0.271 10 false A79 3.375,2.385 3.708,2.604 0.333,0.219 10 false 1*1 3.792,2.385 4.073,2.625 0.281,0.24 10 false 2*2 3.771,2.594 4.156,2.865 0.385,0.271 10 false A80 3.354,2.594 3.667,2.833 0.313,0.24 10 false A79 4.083,2.906 4.906,3.354 0.823,0.448 10 false to Stop Light Circuit 5.979,0.719 6.688,0.99 0.708,0.271 10 false STPO*1 5.99,1.333 6.677,1.635 0.688,0.302 10 false STP2*1 6,2.615 6.396,2.854 0.396,0.24 10 false STP 5.75,2.49 5.979,2.688 0.229,0.198 10 false 33 5.813,1.25 6.042,1.448 0.229,0.198 10 false 6 5.813,0.635 6.042,0.833 0.229,0.198 10 false 3 5.542,3.938 5.833,4.156 0.292,0.219 10 false A58 5.865,3.938 7.042,4.406 1.177,0.469 10 false Brake Booster with Master Cylinder 2.438,3.042 3.688,3.406 1.25,0.365 10 false Stop Light Switch 0.5,3.813 3.146,4.063 2.646,0.25 10 false *1: w/ Dynamic Radar Cruise Control 0.5,4.208 3.063,4.49 2.563,0.281 10 false *2: w/o Dynamic Radar Cruise Control 0.167,1.031 1.021,1.49 0.854,0.458 10 false from Auxiliary Battery 1.458,1.208 1.938,1.438 0.479,0.229 10 false STOP 4.792,0.635 5.021,0.833 0.229,0.198 10 false *1 4.792,1.26 5.021,1.458 0.229,0.198 10 false *1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF




OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

4.INSPECT STOP LIGHT SWITCH
2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

3.RECONFIRM DTC

NG

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (ready).


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1249) is not output A
DTC (C1249) is output (for LHD) B
DTC (C1249) is output (for RHD) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

4.INSPECT STOP LIGHT SWITCH
a.

Check the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).

OK:

The stop light switch is normal.




OK

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U191011E02
1.552,2.135 1.063,2.802 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.875 0.573,1.031 0.292,0.156 10 false A58 0.896,2.813 1.208,2.969 0.313,0.156 10 false STP

Reconnect the stop light switch connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-33 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V
A58-33 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

6.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Turn the power switch on (ready).


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1249) is not output A
DTC (C1249) is output B


HINT:
·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).

·

If the lighting system is normal but the DTC is still output, replace the brake booster with master cylinder (skid control ECU) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL for LHD, Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL for RHD).





A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U191011E02
1.552,2.135 1.063,2.802 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.875 0.573,1.031 0.292,0.156 10 false A58 0.896,2.813 1.208,2.969 0.313,0.156 10 false STP

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-33 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V
A58-33 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)