Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.12–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Check CAN Bus Lines for Short Circuit (RHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Hybrid vehicle control ECU

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Combination meter sub-assembly

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Spiral cable with sensor sub-assembly (Steering angle sensor)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Airbag ECU assembly

·

Transmission control ECU assembly

·

Certification ECU (Smart key ECU assembly)

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector

·

CAN No. 3 junction connector



WIRING DIAGRAM

C356326E02
3.958,7.958 5.688,8.146 1.729,0.188 10 false : CAN Branch Line (CANH) 3.958,8.365 5.688,8.552 1.729,0.188 10 false : CAN Branch Line (CANL) 0.833,7.969 2.75,8.156 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.833,8.385 2.75,8.573 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.469,0.479 3.885,0.667 0.417,0.188 10 false 120 Ω 2.813,1.083 3.219,1.25 0.406,0.167 10 false CANL 0.167,0.708 0.458,0.875 0.292,0.167 10 false L27 4.135,1.604 4.344,1.771 0.208,0.167 10 false SB 5.219,2.938 5.354,3.104 0.135,0.167 10 false L 2.021,5.531 2.177,5.698 0.156,0.167 10 false B 2,6.24 2.156,6.406 0.156,0.167 10 false W 5.198,6.813 5.385,7.073 0.188,0.26 10 false W 3.01,4.198 3.167,4.365 0.156,0.167 10 false W 5.198,5.531 5.354,5.698 0.156,0.167 10 false W 4.146,4.198 4.375,4.365 0.229,0.167 10 false GR 5.208,4.781 5.365,4.948 0.156,0.167 10 false G 3.063,1.594 3.229,1.76 0.167,0.167 10 false G 3.104,1.969 3.427,2.135 0.323,0.167 10 false L132 3.094,3.927 3.5,4.094 0.406,0.167 10 false L132 3.906,4.542 4.177,4.708 0.271,0.167 10 false L94 4.417,4.979 4.74,5.146 0.323,0.167 10 false L95 4.417,5.333 4.677,5.5 0.26,0.167 10 false L95 4.417,6.26 4.719,6.427 0.302,0.167 10 false L95 4.406,6.625 4.74,6.792 0.333,0.167 10 false L95 5.396,7.042 5.677,7.208 0.281,0.167 10 false L54 3.146,4.542 3.417,4.708 0.271,0.167 10 false L94 2.635,5.719 2.896,5.885 0.26,0.167 10 false L95 2.635,6.073 2.896,6.24 0.26,0.167 10 false L95 3.865,3.917 4.26,4.083 0.396,0.167 10 false L132 3.875,1.958 4.198,2.125 0.323,0.167 10 false L132 4.406,2.396 4.698,2.563 0.292,0.167 10 false A67 4.406,2.771 4.698,2.938 0.292,0.167 10 false A67 0.49,0.708 2.688,0.917 2.198,0.208 10 false Combination Meter Sub-assembly 4.104,1.104 4.542,1.271 0.438,0.167 10 false CANH 6.094,5.281 6.5,5.448 0.406,0.167 10 false CANL 5.938,4.938 6.375,5.104 0.438,0.167 10 false CANH 1.052,6.177 1.458,6.344 0.406,0.167 10 false CANL 1.042,5.573 1.479,5.74 0.438,0.167 10 false CANH 5.885,6.75 6.292,6.917 0.406,0.167 10 false CANL 5.854,6.115 6.292,6.281 0.438,0.167 10 false CANH 5.906,2.292 6.344,2.458 0.438,0.167 10 false CA1H 5.896,2.885 6.333,3.052 0.438,0.167 10 false CA1L 4.073,1.354 4.281,1.521 0.208,0.167 10 false 19 2.854,3.917 3.063,4.083 0.208,0.167 10 false 11 2.729,6.271 2.833,6.438 0.104,0.167 10 false 5 2.729,5.479 2.844,5.646 0.115,0.167 10 false 6 5.75,5.438 5.958,5.604 0.208,0.167 10 false 14 5.594,2.292 5.802,2.458 0.208,0.167 10 false 37 5.594,2.885 5.802,3.052 0.208,0.167 10 false 38 4.458,4.771 4.635,4.938 0.177,0.167 10 false 15 4.5,6.823 4.708,6.99 0.208,0.167 10 false 2 4.51,6.052 4.719,6.219 0.208,0.167 10 false 3 5.156,2.219 5.365,2.385 0.208,0.167 10 false LG 2.854,1.906 3.052,2.073 0.198,0.167 10 false 12 3.042,1.354 3.24,1.521 0.198,0.167 10 false 20 4.313,3.906 4.427,4.073 0.115,0.167 10 false 5 4.479,5.542 4.656,5.708 0.177,0.167 10 false 14 5.667,4.844 5.781,5.01 0.115,0.167 10 false 6 4.26,4.5 4.375,4.667 0.115,0.167 10 false 1 2.948,4.5 3.063,4.667 0.115,0.167 10 false 2 4.302,1.906 4.417,2.073 0.115,0.167 10 false 6 4.469,2.188 4.583,2.354 0.115,0.167 10 false 1 1.573,6.177 1.865,6.344 0.292,0.167 10 false 12 1.594,5.583 1.844,5.75 0.25,0.167 10 false 11 5.635,6.74 5.75,6.906 0.115,0.167 10 false 7 5.635,6.146 5.75,6.313 0.115,0.167 10 false 1 4.521,2.99 4.708,3.156 0.188,0.167 10 false 7 5.25,0.563 6.458,0.75 1.208,0.188 10 false x: Suspected Area 5.094,3.167 5.417,3.344 0.323,0.177 10 false A58 5.417,3.167 7.135,3.719 1.719,0.552 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 6.063,5.542 6.375,5.729 0.313,0.188 10 false L61 6.354,5.542 6.75,5.729 0.396,0.188 10 false DLC3 0.896,2.813 2.885,3.313 1.99,0.5 10 false CAN No. 1 Junction Connector 0.885,5.052 2.875,5.24 1.99,0.188 10 false CAN No. 2 Junction Connector 0.146,6.479 0.438,6.635 0.292,0.156 10 false L17 0.469,6.479 2.094,7.042 1.625,0.563 10 false Air Conditioning Amplifier Assembly 5.719,7.042 7.031,7.365 1.313,0.323 10 false Power Steering ECU Assembly 5.208,6.104 5.365,6.271 0.156,0.167 10 false R 0.26,0.125 1.521,0.333 1.26,0.208 12 false V Bus:

C392115E01
4.438,0.167 6.625,0.49 2.188,0.323 10 false CAN No. 2 Junction Connector 1.042,0.208 1.792,0.531 0.75,0.323 10 false CANH 1.042,1.854 1.792,2.177 0.75,0.323 10 false CANH 5.823,0.677 6.573,1 0.75,0.323 10 false CANH 5.854,1.292 6.49,1.604 0.635,0.313 10 false CANL 1.042,0.833 1.677,1.146 0.635,0.313 10 false CANL 1.052,2.469 1.688,2.781 0.635,0.313 10 false CANL 0.052,1.094 0.531,1.396 0.479,0.302 10 false L197 0.396,1.083 1.917,1.719 1.521,0.635 10 false Certification ECU (Smart Key ECU Assembly) 1.563,0.208 1.917,0.479 0.354,0.271 10 false 14 1.542,0.833 1.896,1.104 0.354,0.271 10 false 15 2.021,0.177 2.375,0.448 0.354,0.271 10 false B 1.99,0.906 2.344,1.177 0.354,0.271 10 false W 2.625,0.698 2.979,0.969 0.354,0.271 10 false L94 4.417,0.792 4.771,1.063 0.354,0.271 10 false L94 2.615,0.333 2.969,0.604 0.354,0.271 10 false L94 4.427,1.167 4.781,1.438 0.354,0.271 10 false L94 3.135,2.625 3.49,2.896 0.354,0.271 10 false L94 3.906,2.625 4.26,2.896 0.354,0.271 10 false L94 2.635,1.969 2.99,2.24 0.354,0.271 10 false L95 2.625,2.333 2.979,2.604 0.354,0.271 10 false L95 2.688,0.135 3.042,0.406 0.354,0.271 10 false 7 2.698,0.917 3.052,1.188 0.354,0.271 10 false 8 0.063,2.719 0.542,3.021 0.479,0.302 10 false L16 0.354,2.719 1.813,2.979 1.458,0.26 10 false Airbag ECU Assembly 1.542,1.833 1.896,2.104 0.354,0.271 10 false 13 1.552,2.469 1.906,2.74 0.354,0.271 10 false 22 1.958,2.51 2.313,2.781 0.354,0.271 10 false W 1.99,1.802 2.344,2.073 0.354,0.271 10 false B 2.698,2.542 3.052,2.813 0.354,0.271 10 false 8 2.708,1.771 3.063,2.042 0.354,0.271 10 false 9 4.469,0.594 4.823,0.865 0.354,0.271 10 false 10 4.469,1.375 4.823,1.646 0.354,0.271 10 false 11 5.156,1.365 5.51,1.635 0.354,0.271 10 false W 5.177,0.646 5.531,0.917 0.354,0.271 10 false B 5.646,1.302 6,1.573 0.354,0.271 10 false 3 5.615,0.677 5.969,0.948 0.354,0.271 10 false 4 5.281,1.563 5.917,1.875 0.635,0.313 10 false L51 5.573,1.552 7.115,2.448 1.542,0.896 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) 4.292,2.635 4.646,2.906 0.354,0.271 10 false 4 2.927,2.635 3.281,2.906 0.354,0.271 10 false 5 2.979,2.948 3.333,3.219 0.354,0.271 10 false W 4.146,2.927 4.5,3.198 0.354,0.271 10 false B 3.865,3.281 4.229,3.552 0.365,0.271 10 false L133 3.115,3.281 3.479,3.552 0.365,0.271 10 false L133 2.583,3.677 2.948,3.948 0.365,0.271 10 false L133 2.594,4.052 2.958,4.323 0.365,0.271 10 false L133 2.573,5.323 2.938,5.594 0.365,0.271 10 false L133 2.594,5.688 2.958,5.958 0.365,0.271 10 false L133 4.427,4.01 4.792,4.281 0.365,0.271 10 false A68 4.417,4.375 4.781,4.646 0.365,0.271 10 false A68 3.906,6.021 4.271,6.292 0.365,0.271 10 false A68 3.146,6.021 3.51,6.292 0.365,0.271 10 false A68 4.292,3.26 4.646,3.531 0.354,0.271 10 false 6 2.844,3.281 3.198,3.552 0.354,0.271 10 false 12 4.49,3.813 4.844,4.083 0.354,0.271 10 false 2 4.5,4.594 4.854,4.865 0.354,0.271 10 false 8 5.146,3.823 5.5,4.094 0.354,0.271 10 false Y 5.115,4.552 5.469,4.823 0.354,0.271 10 false BR 5.563,3.865 5.917,4.135 0.354,0.271 10 false 16 5.563,4.49 5.917,4.76 0.354,0.271 10 false 15 5.865,4.5 6.5,4.813 0.635,0.313 10 false CA1L 1.083,4.146 1.719,4.458 0.635,0.313 10 false CA1L 1.073,5.792 1.708,6.104 0.635,0.313 10 false CANL 2.823,6.896 3.458,7.208 0.635,0.313 10 false CANL 1.063,5.198 1.813,5.521 0.75,0.323 10 false CANH 4.094,6.885 4.844,7.208 0.75,0.323 10 false CANH 5.854,3.885 6.385,4.167 0.531,0.281 10 false CA1H 1.063,3.573 1.594,3.854 0.531,0.281 10 false CA1H 2.656,4.26 3.01,4.531 0.354,0.271 10 false 10 2.698,3.458 3.052,3.729 0.354,0.271 10 false 4 1.99,3.51 2.344,3.781 0.354,0.271 10 false V 2,4.219 2.354,4.49 0.354,0.271 10 false P 0.063,4.438 0.542,4.74 0.479,0.302 10 false L6 0.281,4.438 2.031,4.771 1.75,0.333 10 false Hybrid Vehicle Control ECU 1.552,3.563 1.906,3.833 0.354,0.271 10 false 25 1.563,4.156 1.917,4.427 0.354,0.271 10 false 24 0.063,6.073 0.542,6.375 0.479,0.302 10 false L201 0.396,6.063 2.042,6.615 1.646,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 1.542,5.188 1.896,5.458 0.354,0.271 10 false 14 1.542,5.792 1.896,6.063 0.354,0.271 10 false 13 1.969,5.865 2.323,6.135 0.354,0.271 10 false W 1.958,5.135 2.313,5.406 0.354,0.271 10 false SB 2.635,5.885 2.99,6.156 0.354,0.271 10 false 11 2.708,5.104 3.063,5.375 0.354,0.271 10 false 5 4.271,6.042 4.625,6.313 0.354,0.271 10 false 1 2.927,6.031 3.281,6.302 0.354,0.271 10 false 7 4.135,6.406 4.49,6.677 0.354,0.271 10 false P 3.021,6.417 3.375,6.688 0.354,0.271 10 false V 5.406,4.74 5.771,5.01 0.365,0.271 10 false A24 5.708,4.729 7.031,5.313 1.323,0.583 10 false Transmission Control ECU Assembly 4.49,5.719 6.698,6.135 2.208,0.417 10 false CAN No. 3 Junction Connector 3.104,6.646 3.458,6.917 0.354,0.271 10 false 5 4.104,6.646 4.458,6.917 0.354,0.271 10 false 13 3.448,7.51 4.198,7.833 0.75,0.323 10 false 120 Ω 4.698,7.063 5.438,7.385 0.74,0.323 10 false A57 5,7.063 5.74,7.385 0.74,0.323 10 false ECM 0.594,7.188 2.146,7.552 1.552,0.365 10 false x: Suspected Area 0.792,7.885 2.719,8.156 1.927,0.271 10 false : CAN Main Bus Line (CANH) 0.792,8.302 2.719,8.573 1.927,0.271 10 false : CAN Main Bus Line (CANL) 3.99,7.906 5.917,8.177 1.927,0.271 10 false : CAN Branch Line (CANH) 3.99,8.313 5.917,8.583 1.927,0.271 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (ECM)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154712E01
1.603,0.657 1.906,0.813 0.303,0.156 10 A57 0.178,0.182 0.532,0.455 0.353,0.273 10 *a 2.581,1.039 3.042,1.275 0.461,0.236 10 CANH 2.473,0.795 2.950,1.045 0.477,0.250 10 CANL 1.93,1.677 2.184,0.892 2.184,0.892 2.43,0.892 false 1.958,1.789 2.242,1.117 2.242,1.117 2.533,1.117 false

Disconnect the A57 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

2.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER SUB-ASSEMBLY)
2.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER SUB-ASSEMBLY)
a.

Reconnect the A57 ECM connector.


b.
U154716E02
2.844,2.469 3.052,2.927 false 2.719,2.469 2.333,2.927 false 0.198,0.156 0.438,0.5 0.24,0.344 10 false *a 2.802,2.948 3.26,3.115 0.458,0.167 10 false CANL 2.125,2.958 2.583,3.125 0.458,0.167 10 false CANH 1.677,0.74 1.99,0.906 0.313,0.167 10 false L27

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)


Result:
Result Proceed to
OK (w/o Multi-information Display) A
OK (w/ Multi-information Display) B
NG C



A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

3.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the L27 combination meter sub-assembly connector.


b.
U191015E02
0.969,1.104 1.063,1.104 1.063,1.104 1.521,1.646 false 2.552,1.083 1.99,1.083 1.99,1.083 1.75,1.646 false 1,1.625 1.094,1.625 1.094,1.625 1.552,1.833 false 2.573,1.583 2.01,1.583 2.01,1.583 1.76,1.823 false 2.583,2.26 2.427,2.26 2.427,2.26 1.76,2.052 false 0.969,2.271 1.063,2.271 1.063,2.271 1.531,2.042 false 2.583,2.708 2.427,2.708 2.427,2.708 1.76,2.281 false 0.969,2.719 1.063,2.719 1.063,2.719 1.531,2.271 false 0.156,0.156 0.708,0.521 0.552,0.365 10 false *a 0.417,1.021 1,1.25 0.583,0.229 10 false CANH*b 2.615,0.969 3.208,1.219 0.594,0.25 10 false CANL*b 0.406,1.531 0.958,1.802 0.552,0.271 10 false CANH*c 2.615,1.5 3.198,1.75 0.583,0.25 10 false CANL*c 1.604,0.615 1.99,0.906 0.385,0.292 10 false L94 2.615,2.188 3.229,2.458 0.615,0.271 10 false CANL*d 0.396,2.177 0.969,2.354 0.573,0.177 10 false CANH*d 2.615,2.615 3.229,2.885 0.615,0.271 10 false CANL*e 0.417,2.625 1.031,2.906 0.615,0.281 10 false CANH*e

Disconnect the L94 wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder left side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-1 (CANH) - L94-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 1 junction connector
L94-4 (CANH) - L94-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
L94-7 (CANH) - L94-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Certification ECU (Smart key ECU assembly)
L94-10 (CANH) - L94-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly (Steering angle sensor)


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector
*c to CAN No. 3 Junction Connector
*d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)

Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main lines) B
NG (CAN No. 3 junction connector main lines) C
NG (ECU or sensor branch lines) D




A

4.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 JUNCTION CONNECTOR)

B

5.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU OR SENSOR)
4.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the L95 wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder right side).


b.
U191016E03
1,1.083 1.229,1.083 1.229,1.083 1.698,1.635 false 2.563,1.104 2.135,1.104 2.135,1.104 1.896,1.667 false 0.99,1.615 1.219,1.615 1.219,1.615 1.677,1.833 false 2.573,1.635 2.146,1.635 2.146,1.635 1.896,1.875 false 2.542,2.281 2.385,2.281 2.385,2.281 1.865,2.073 false 0.99,2.323 1.219,2.323 1.219,2.323 1.688,2.104 false 2.5,3 2.354,3 2.354,3 1.844,2.469 false 0.979,3.021 1.208,3.021 1.208,3.021 1.708,2.469 false 0.188,0.104 0.74,0.469 0.552,0.365 10 false *a 2.615,1.021 3.24,1.25 0.625,0.229 10 false CANH*b 0.458,1 1.052,1.25 0.594,0.25 10 false CANL*b 2.625,1.552 3.198,1.823 0.573,0.271 10 false CANH*c 0.458,1.531 1.042,1.781 0.583,0.25 10 false CANL*c 1.625,0.594 1.885,0.771 0.26,0.177 10 false L95 0.448,2.24 1.063,2.51 0.615,0.271 10 false CANL*d 2.615,2.198 3.198,2.375 0.583,0.177 10 false CANH*d 0.458,2.948 1.073,3.219 0.615,0.271 10 false CANL*e 2.583,2.906 3.146,3.083 0.563,0.177 10 false CANH*e

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L95-3 (CANH) - L95-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
L95-6 (CANH) - L95-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
L95-9 (CANH) - L95-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag ECU assembly
L95-15 (CANH) - L95-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher DLC3


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
*c to Air Conditioning Amplifier Assembly
*d to Airbag ECU Assembly
*e to DLC3


Result:
Result Proceed to
OK A
NG (ECU or sensor branch lines) B
NG (DLC3 branch lines) C



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU OR SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINES CONNECTED TO DLC3

5.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 JUNCTION CONNECTOR)
a.
U154810E03
2.115,1.74 2.115,0.969 2.115,0.969 2.458,0.969 false 2.135,2.073 2.135,2.552 2.135,2.552 2.5,2.552 false 1.01,2.563 1.958,2.563 1.958,2.563 1.958,2.073 false 0.844,0.979 1.969,0.979 1.969,0.979 1.969,1.74 false 0.115,0 0.375,0.219 0.26,0.219 10 false *a 1.542,0.583 1.896,0.792 0.354,0.208 10 false L132 2.521,0.885 3.188,1.208 0.667,0.323 10 false CANH*c 0.24,0.875 0.906,1.198 0.667,0.323 10 false CANH*b 2.573,2.458 3.24,2.781 0.667,0.323 10 false CANL*c 0.417,2.458 1.083,2.781 0.667,0.323 10 false CANL*b

Disconnect the L132 wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L132-5 (CANH) - L132-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher CAN No. 2 junction connector
L132-6 (CANH) - L132-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter sub-assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector
*c to Combination Meter Sub-assembly


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main lines) B
NG (Combination meter sub-assembly main lines) C



A

6.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - COMBINATION METER SUB-ASSEMBLY)

6.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the A67 wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.


U191036E02
1.01,2.583 1.26,2.583 1.26,2.583 1.26,2.094 false 0.844,0.948 1.271,0.948 1.271,0.948 1.271,1.708 false 0.104,0.094 0.479,0.365 0.375,0.271 10 false *a 1.573,0.604 1.917,0.833 0.344,0.229 10 false A67 0.25,0.844 0.917,1.167 0.667,0.323 10 false CANH*b 0.354,2.49 1.021,2.813 0.667,0.323 10 false CANL*b

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - A67-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECU or sensor branch lines) B



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU OR SENSOR)
7.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.

Disconnect the L133 wire harness connector from the CAN No. 3 junction connector (instrument panel wire side).


b.
U191038E02
1.792,2.094 1.792,2.677 1.792,2.677 1.448,2.677 false 1.792,1.719 1.792,0.771 1.792,0.771 1.448,0.771 false 2.354,0.771 2.146,0.771 2.146,0.771 2.146,1.708 false 2.406,2.677 2.135,2.677 2.135,2.677 2.135,2.094 false 1.969,1.708 1.969,0.385 1.969,0.385 1.656,0.385 false 1.979,2.094 1.979,3.01 1.979,3.01 1.635,3.01 false 0.156,0.115 0.479,0.479 0.323,0.365 10 false *a 0.406,1.667 0.875,1.927 0.469,0.26 10 false L133 0.854,0.698 1.521,1.021 0.667,0.323 10 false CANH*b 0.885,2.583 1.552,2.906 0.667,0.323 10 false CANL*b 1.073,2.938 1.698,3.135 0.625,0.198 10 false CANL*c 2.417,0.708 3.083,1.031 0.667,0.323 10 false CANH*d 2.49,2.583 3.115,2.781 0.625,0.198 10 false CANL*d 1.104,0.281 1.771,0.604 0.667,0.323 10 false CANH*c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L133-4 (CANH) -L133-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
L133-5 (CANH) -L133-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
L133-6 (CANH) - L133-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher CAN No. 2 junction connector


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Hybrid vehicle control ECU
*c to Main Body ECU (Multiplex Network Body ECU)
*d to CAN No. 2 Junction Connector


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main lines) B
NG (ECU or sensor branch lines) C



A

8.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU OR SENSOR)
8.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.
U191037E02
1.26,1.719 1.26,0.948 1.26,0.948 0.917,0.948 false 1.271,2.104 1.271,2.708 1.271,2.708 0.927,2.708 false 1.438,1.719 1.438,0.948 1.438,0.948 1.781,0.948 false 1.438,2.115 1.438,2.719 1.438,2.719 1.781,2.719 false 0.115,0 0.375,0.219 0.26,0.219 10 false *a 0.427,1.667 0.896,1.948 0.469,0.281 10 false A68 0.354,0.844 1.021,1.167 0.667,0.323 10 false CANH*b 0.365,2.625 1.031,2.948 0.667,0.323 10 false CANL*b 1.854,0.875 2.521,1.198 0.667,0.323 10 false CANH*c 1.844,2.615 2.51,2.938 0.667,0.323 10 false CANL*c

Disconnect the A68 wire harness connector from the CAN No. 3 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A68-1 (CANH) - A68-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
A68-2 (CANH) - A68-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Transmission control ECU assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to ECM
*c to Transmission Control ECU Assembly

Result:
Result Proceed to
OK A
NG (ECM main lines) B
NG (ECU or sensor branch lines) C




A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - ECM)

C

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU OR SENSOR)
9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).


c.
U154762E02
2.073,1.823 2.438,1.271 false 2.083,2.531 2.417,2.865 false 0.083,0.031 0.927,0.365 0.844,0.333 10 false *1 1.604,0.813 1.917,0.99 0.313,0.177 10 false L61 2.448,1.063 2.854,1.24 0.406,0.177 10 false CANH 2.438,2.906 2.823,3.083 0.385,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-6 (CANH) - L61-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*1 DLC3


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, repair or replace the short circuited branch line or connector.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINES OR CONNECTOR