Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 5 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Hybrid vehicle control ECU

·

Driving support ECU assembly

(w/ Toyota Safety Sense)

·

Forward recognition camera

(w/ Toyota Safety Sense)

·

Parking assist ECU

(w/ Intelligent Parking Assist System)

·

Millimeter wave radar sensor assembly

(w/ Toyota Safety Sense)

·

No. 4 CAN junction connector



WIRING DIAGRAM

C392134E01
0.302,0.875 1.073,1.073 0.771,0.198 10 false 120 Ω 0.354,6.667 1.125,6.865 0.771,0.198 10 false 120 Ω 0.875,0.542 1.365,0.75 0.49,0.208 10 false CA5H 0.906,1.031 1.396,1.24 0.49,0.208 10 false CA5L 1.344,0.542 1.833,0.75 0.49,0.208 10 false 15 1.354,1.021 1.844,1.229 0.49,0.208 10 false 16 3.406,0.656 3.896,0.865 0.49,0.208 10 false L198 3.406,1.125 3.896,1.333 0.49,0.208 10 false L198 3.51,0.458 4,0.667 0.49,0.208 10 false 1 3.531,0.927 4.021,1.135 0.49,0.208 10 false 2 4.688,0.656 5.177,0.865 0.49,0.208 10 false L185 4.698,1.125 5.188,1.333 0.49,0.208 10 false L185 4.802,0.458 5.292,0.667 0.49,0.208 10 false 1 4.823,0.938 5.313,1.146 0.49,0.208 10 false 2 5.5,1.531 5.99,1.74 0.49,0.208 10 false U15 5.802,1.531 7.083,2.063 1.281,0.531 10 false Forward Recognition Camera*1 6.021,0.646 6.51,0.854 0.49,0.208 10 false CA1P 6.021,1.115 6.51,1.323 0.49,0.208 10 false CA1N 5.823,0.521 6.313,0.729 0.49,0.208 10 false 5 5.771,1 6.26,1.208 0.49,0.208 10 false 11 1.698,3.344 2.969,3.875 1.271,0.531 10 false Driving Support ECU Assembly*1 1.354,3.344 1.844,3.552 0.49,0.208 10 false L205 2.156,2.438 2.646,2.646 0.49,0.208 10 false CA2H 2.177,2.906 2.667,3.115 0.49,0.208 10 false CA2L 2.646,2.333 3.135,2.542 0.49,0.208 10 false 10 2.656,2.802 3.146,3.01 0.49,0.208 10 false 11 3.417,2.438 3.906,2.646 0.49,0.208 10 false L182 3.427,2.917 3.917,3.125 0.49,0.208 10 false L182 3.542,2.26 4.031,2.469 0.49,0.208 10 false 1 3.531,2.719 4.021,2.927 0.49,0.208 10 false 2 4.688,2.438 5.177,2.646 0.49,0.208 10 false L184 4.698,2.917 5.188,3.125 0.49,0.208 10 false L184 4.802,2.25 5.292,2.458 0.49,0.208 10 false 1 4.813,2.729 5.302,2.938 0.49,0.208 10 false 2 5.76,2.323 6.25,2.531 0.49,0.208 10 false 34 5.76,2.813 6.25,3.021 0.49,0.208 10 false 35 6.021,2.427 6.51,2.635 0.49,0.208 10 false CA2H 6.031,2.906 6.521,3.115 0.49,0.208 10 false CA2L 5.75,3.354 6.24,3.563 0.49,0.208 10 false L5 5.969,3.354 6.896,3.906 0.927,0.552 10 false Hybrid Vehicle Control ECU 1.385,5.271 1.875,5.479 0.49,0.208 10 false L65 1.667,5.26 3.083,5.51 1.417,0.25 10 false Parking Assist ECU*2 2.146,4.385 2.635,4.594 0.49,0.208 10 false CANH 2.167,4.865 2.656,5.073 0.49,0.208 10 false CANL 2.656,4.281 3.146,4.49 0.49,0.208 10 false 40 2.646,4.74 3.135,4.948 0.49,0.208 10 false 39 3.417,4.396 3.906,4.604 0.49,0.208 10 false L183 3.417,4.865 3.906,5.073 0.49,0.208 10 false L183 3.521,4.656 4.01,4.865 0.49,0.208 10 false 2 3.521,4.198 4.01,4.406 0.49,0.208 10 false 1 4.698,4.396 5.188,4.604 0.49,0.208 10 false L203 3.417,6.438 3.906,6.646 0.49,0.208 10 false L199 4.813,4.677 5.302,4.885 0.49,0.208 10 false 2 4.802,4.198 5.292,4.406 0.49,0.208 10 false 1 3.427,6.906 3.917,7.115 0.49,0.208 10 false L199 4.708,4.875 5.198,5.083 0.49,0.208 10 false L203 3.542,6.719 4.031,6.927 0.49,0.208 10 false 2 3.542,6.24 4.031,6.448 0.49,0.208 10 false 1 3.208,7.24 5.167,7.479 1.958,0.24 10 false No. 4 CAN Junction Connector 5.813,4.26 6.281,4.469 0.469,0.208 10 false 3 5.823,4.75 6.292,4.958 0.469,0.208 10 false 2 6.052,4.396 6.542,4.604 0.49,0.208 10 false CA2H 6.042,4.854 6.531,5.063 0.49,0.208 10 false CA2L 5.385,5.323 5.875,5.531 0.49,0.208 10 false A91 5.708,5.323 7.115,5.844 1.406,0.521 10 false Millimeter Wave Radar Sensor Assembly*1 0.875,6.344 1.365,6.552 0.49,0.208 10 false CAXH 0.917,6.833 1.406,7.042 0.49,0.208 10 false CAXL 0.073,7.313 0.844,7.51 0.771,0.198 10 false L192 0.406,7.302 2.365,7.875 1.958,0.573 10 false Central Gateway ECU (Network Gateway ECU) 3.24,7.813 5.958,8.052 2.719,0.24 10 false *1: w/ Toyota Safety Sense 3.24,8.198 5.958,8.438 2.719,0.24 10 false *2: w/ Intelligent Parking Assist System 1.385,6.333 1.875,6.542 0.49,0.208 10 false 9 1.385,6.823 1.875,7.031 0.49,0.208 10 false 24

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L182, L183, L184, L185, L198, L199 and L203 No. 4 CAN junction connectors.


c.

Measure the resistance according to the value(s) in the table below.

HINT:
·

Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.

·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C421483C31
5.667,0.583 6.083,0.833 0.417,0.25 0.75,1.667 0.917,1.833 0.917,1.833 1.083,1.833 true 0.719,1.49 0.917,1.25 0.917,1.25 1.083,1.25 true 5.854,1.396 6.063,1.042 6.063,1.042 6.229,1.042 true 1.781,0.896 2.094,1.094 0.313,0.198 10 false *b 0.458,0.969 0.771,1.167 0.313,0.198 10 false *a 5.781,0.635 6.385,0.844 0.604,0.208 10 false L61 1.188,1.177 1.698,1.385 0.51,0.208 10 false CANL 4.927,0.917 5.24,1.115 0.313,0.198 10 false *1 1.167,1.75 1.677,1.958 0.51,0.208 10 false CANH 6.302,0.969 6.906,1.177 0.604,0.208 10 false CG
*1 DLC3 - -
*a Vehicle wire harness connector connected to CAN junction connector *b Rear view of wire harness connector
(to No. 4 CAN Junction Connector)


Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition Connected to
L203-1 (CANH) - L61-4 (CG) B Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*1
L203-2 (CANL) - L61-4 (CG) BE
L199-1 (CANH) - L61-4 (CG) B Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
L199-2 (CANL) - L61-4 (CG) P
L198-1 (CANH) - L61-4 (CG) B Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
L198-2 (CANL) - L61-4 (CG) V
L185-1 (CANH) - L61-4 (CG) B Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward recognition camera*1
L185-2 (CANL) - L61-4 (CG) W
L184-1 (CANH) - L61-4 (CG) B Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
L184-2 (CANL) - L61-4 (CG) G
L183-1 (CANH) - L61-4 (CG) B Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Parking assist ECU*2
L183-2 (CANL) - L61-4 (CG) L
L182-1 (CANH) - L61-4 (CG) B Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Driving support ECU assembly*1
L182-2 (CANL) - L61-4 (CG) R


·

*1: w/ Toyota Safety Sense

·

*2: w/ Intelligent Parking Assist System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


b.
C354521C98
1.479,0.063 1.969,0.281 0.49,0.219 2.771,0.906 2.771,0.323 2.771,0.323 2.604,0.323 true 1.51,1.219 1.51,1.802 1.51,1.802 1.677,1.802 true 2.896,1.219 2.896,1.802 2.896,1.802 2.729,1.802 true 1.375,1.208 1.375,1.792 1.375,1.792 1.208,1.792 true 2.938,0.906 2.938,0.156 2.938,0.156 2.771,0.156 true 1.563,0.094 2.177,0.292 0.615,0.198 10 false L192 0.813,1.729 1.427,1.927 0.615,0.198 10 false CA5H 1.76,1.74 2.375,1.938 0.615,0.198 10 false CA5L 2.344,1.75 2.927,1.917 0.583,0.167 10 false CAXL 2.208,0.271 2.823,0.469 0.615,0.198 10 false CAXH 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a 2.427,0.094 3.042,0.292 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L192-15 (CA5H) - L192-10 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-16 (CA5L) - L192-10 (GND)
L192-9 (CAXH) - L192-10 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-24 (CAXL) - L192-10 (GND)




OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 CAN JUNCTION CONNECTOR)

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).


c.

Measure the resistance according to the value(s) in the table below.

C351275C87
1.594,0.198 2.01,0.469 0.417,0.271 4.938,0.292 5.354,0.563 0.417,0.271 1.875,2.49 2.01,2.49 2.01,2.49 2.01,1.406 true 4.958,0.74 5.125,0.74 5.125,0.74 5.125,1.073 true 2.271,2.49 2.104,2.49 2.104,2.49 2.104,1.406 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.646,0.26 2.042,0.438 0.396,0.177 10 false L192 1.49,2.417 2.042,2.615 0.552,0.198 10 false CA5L 4.708,0.677 5.26,0.875 0.552,0.198 10 false CG 2.365,2.396 2.917,2.594 0.552,0.198 10 false CA5H 5.042,0.344 5.354,0.542 0.313,0.198 10 false L61 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
L192-15 (CA5H) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-16 (CA5L) - L61-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.





OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR