Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.12–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 1 CAN junction connector (engine room main wire side).

i.

Connection diagram

C234761C50
3.417,0.25 3.823,0.479 0.406,0.229 3.219,1.729 3.219,2.146 3.219,2.146 3.052,2.146 true 3.219,1.406 3.219,0.823 3.219,0.823 3.052,0.823 true 3.354,1.396 3.354,0.646 3.354,0.646 3.188,0.646 true 3.354,1.729 3.354,2.313 3.354,2.313 3.188,2.313 true 3.51,1.396 3.51,0.646 3.51,0.646 3.677,0.646 true 3.635,1.396 3.635,0.813 3.635,0.813 3.802,0.813 true 3.5,1.729 3.5,2.313 3.5,2.313 3.667,2.313 true 3.646,1.719 3.646,2.135 3.646,2.135 3.813,2.135 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.51,0.281 3.781,0.469 0.271,0.188 10 false A67 2.49,0.74 3.135,0.979 0.646,0.24 10 false CANH*b 2.51,2.073 3.156,2.313 0.646,0.24 10 false CANL*b 2.625,0.573 3.271,0.813 0.646,0.24 10 false CANH*c 2.656,2.24 3.302,2.479 0.646,0.24 10 false CANL*c 3.76,0.563 4.406,0.802 0.646,0.24 10 false CANH*d 3.875,0.729 4.521,0.969 0.646,0.24 10 false CANH*e 3.74,2.229 4.385,2.469 0.646,0.24 10 false CANL*d 3.896,2.052 4.542,2.292 0.646,0.24 10 false CANL*e
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU) *d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
*e to ECM - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) P ECM
(for Bus 2)
A67-7 (CANL) V
A67-2 (CANH) LG Brake booster with master cylinder assembly (skid control ECU)
(for Bus 2)
A67-8 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (skid control ECU)
(for Sub bus 15)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 15)
A67-10 (CANL) W



b.

Check the No. 1 CAN junction connector (instrument panel wire side).

i.

Connection diagram

C234761C51
3.417,0.25 3.823,0.479 0.406,0.229 3.51,1.729 3.51,2.146 3.51,2.146 3.344,2.146 true 3.51,1.406 3.51,0.823 3.51,0.823 3.344,0.823 true 3.792,1.396 3.792,0.646 3.792,0.646 3.625,0.646 true 3.802,1.729 3.802,2.313 3.802,2.313 3.635,2.313 true 3.938,1.396 3.938,0.813 3.938,0.813 4.104,0.813 true 3.948,1.719 3.948,2.135 3.948,2.135 4.115,2.135 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.469,0.281 3.896,0.49 0.427,0.208 10 false L132 2.802,0.76 3.448,1 0.646,0.24 10 false CANH*b 2.823,2.073 3.469,2.313 0.646,0.24 10 false CANL*b 3.073,0.583 3.719,0.823 0.646,0.24 10 false CANH*c 3.115,2.25 3.76,2.49 0.646,0.24 10 false CANL*c 4.177,0.74 4.823,0.979 0.646,0.24 10 false CANH*d 4.208,2.063 4.854,2.302 0.646,0.24 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
*c to Main Body ECU (Multiplex Network Body ECU) *d to No. 2 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R No. 5 CAN junction connector
(for Sub bus 15)
L132-9 (CANL) Y
L132-5 (CANH) SB Main body ECU (multiplex network body ECU)
(for Bus 2)
L132-11 (CANL) W
L132-6 (CANH) B No. 2 CAN junction connector
(for Bus 2)
L132-12 (CANL) W




NO. 2 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 2 CAN junction connector (instrument panel connector holder left side).

i.

Connection diagram

C214318C23
3.375,0.573 3.781,0.781 0.406,0.208 4.292,1.146 4.146,1.146 4.146,1.146 3.615,1.365 true 4.292,1.438 4.125,1.438 4.125,1.438 3.615,1.521 true 4.302,1.792 4.167,1.792 4.167,1.792 3.615,1.677 true 4.302,2.052 4.167,2.052 4.167,2.052 3.625,1.823 true 2.75,1.146 2.896,1.146 2.896,1.146 3.427,1.365 true 2.74,1.438 2.906,1.438 2.906,1.438 3.417,1.521 true 2.729,1.792 2.865,1.792 2.865,1.792 3.417,1.677 true 2.74,2.063 2.875,2.063 2.875,2.063 3.417,1.833 true 0.115,0.104 0.781,0.438 0.667,0.333 10 false *a 4.365,1.083 4.958,1.354 0.594,0.271 10 false CANH*b 4.354,1.365 4.99,1.615 0.635,0.25 10 false CANH*c 4.365,1.719 4.958,1.958 0.594,0.24 10 false CANH*d 4.365,1.969 5.063,2.281 0.698,0.313 10 false CANH*e 2.208,1.073 2.833,1.313 0.625,0.24 10 false CANL*b 2.208,1.365 2.844,1.646 0.635,0.281 10 false CANL*c 2.198,1.708 2.771,1.969 0.573,0.26 10 false CANL*d 2.198,1.99 2.813,2.229 0.615,0.24 10 false CANL*e 3.469,0.615 3.885,0.927 0.417,0.313 10 false L94
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
*c to No. 1 CAN Junction Connector *d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-2 (CANH) GR No. 3 CAN junction connector
(for Bus 2)
L94-1 (CANL) W
L94-5 (CANH) B No. 1 CAN junction connector
(for Bus 2)
L94-4 (CANL) W
L94-8 (CANH) B Certification ECU (smart key ECU assembly)
(for Bus 2)
L94-7 (CANL) W
L94-11 (CANH) B Spiral cable with sensor sub-assembly (steering angle sensor)
(for Bus 2)
L94-10 (CANL) W



b.

Check the No. 2 CAN junction connector (instrument panel connector holder right side).

i.

Connection diagram

C214318C24
3.375,0.542 3.823,0.781 0.448,0.24 2.865,1.146 3.01,1.146 3.01,1.146 3.542,1.365 true 2.875,1.438 3.042,1.438 3.042,1.438 3.542,1.521 true 2.854,1.792 2.99,1.792 2.99,1.792 3.542,1.677 true 2.885,2.083 3.021,2.083 3.021,2.083 3.573,1.875 true 4.396,1.146 4.25,1.146 4.25,1.146 3.719,1.365 true 4.396,1.438 4.229,1.438 4.229,1.438 3.719,1.521 true 4.417,1.792 4.271,1.792 4.271,1.792 3.729,1.677 true 4.427,2.052 4.292,2.052 4.292,2.052 3.708,1.875 true 0.115,0.094 0.781,0.427 0.667,0.333 10 false *a 2.323,1.063 2.854,1.302 0.531,0.24 10 false CANH*b 2.323,1.344 2.885,1.604 0.563,0.26 10 false CANH*c 2.313,1.708 2.885,1.948 0.573,0.24 10 false CANH*d 2.333,2 2.938,2.198 0.604,0.198 10 false CANH*e 4.458,1.083 5,1.365 0.542,0.281 10 false CANL*b 4.458,1.375 4.99,1.656 0.531,0.281 10 false CANL*c 4.458,1.719 5.094,2.021 0.635,0.302 10 false CANL*d 4.469,1.979 5.083,2.271 0.615,0.292 10 false CANL*e 3.49,0.594 3.792,0.76 0.302,0.167 10 false L95
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Power Steering ECU Assembly
*c to Air Conditioning Amplifier Assembly *d to Airbag ECU Assembly
*e to Central Gateway ECU (Network Gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-2 (CANH) R Power steering ECU assembly
(for Bus 2)
L95-3 (CANL) W
L95-5 (CANH) B Air conditioning amplifier assembly
(for Bus 2)
L95-6 (CANL) W
L95-8 (CANH) B Airbag ECU assembly
(for Bus 2)
L95-9 (CANL) W
L95-11 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 2)
L95-12 (CANL) W




NO. 3 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 3 CAN junction connector (engine room main wire side).

i.

Connection diagram

C234761C52
3.417,0.25 3.823,0.479 0.406,0.229 3.219,1.729 3.219,2.146 3.219,2.146 3.052,2.146 true 3.219,1.406 3.219,0.823 3.219,0.823 3.052,0.823 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.51,0.281 3.781,0.469 0.271,0.188 10 false A68 2.49,0.74 3.135,0.979 0.646,0.24 10 false CANH*b 2.51,2.073 3.156,2.313 0.646,0.24 10 false CANL*b
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Transmission Control ECU Assembly



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) Y Transmission control ECU assembly
(for Bus 2)
A68-7 (CANL) BR



b.

Check the No. 3 CAN junction connector (instrument panel wire side).

i.

Connection diagram

C234761C53
3.417,0.25 3.823,0.479 0.406,0.229 3.646,1.729 3.646,2.146 3.646,2.146 3.479,2.146 true 3.646,1.406 3.646,0.823 3.646,0.823 3.479,0.823 true 3.802,1.396 3.802,0.646 3.802,0.646 3.969,0.646 true 3.948,1.396 3.948,0.813 3.948,0.813 4.115,0.813 true 3.792,1.729 3.792,2.313 3.792,2.313 3.958,2.313 true 3.948,1.719 3.948,2.135 3.948,2.135 4.115,2.135 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.49,0.281 3.906,0.479 0.417,0.198 10 false L133 2.917,0.75 3.563,0.99 0.646,0.24 10 false CANH*b 2.948,2.073 3.594,2.313 0.646,0.24 10 false CANL*b 4.042,0.573 4.688,0.813 0.646,0.24 10 false CANH*c 4.198,0.729 4.844,0.969 0.646,0.24 10 false CANH*d 4.031,2.229 4.677,2.469 0.646,0.24 10 false CANL*c 4.198,2.052 4.844,2.292 0.646,0.24 10 false CANL*d
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to No. 2 CAN Junction Connector *d to Combination Meter Sub-assembly



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Hybrid vehicle control ECU
(for Bus 2)
L133-10 (CANL) P
L133-5 (CANH) GR No. 2 CAN junction connector
(for Bus 2)
L133-11 (CANL) W
L133-6 (CANH) SB Combination meter sub-assembly
(for Bus 2)
L133-12 (CANL) G




NO. 1 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 1 CAN junction connector (engine room main wire side).

i.

Connection diagram

C234761C69
3.417,0.25 3.823,0.479 0.406,0.229 3.219,1.729 3.219,2.146 3.219,2.146 3.052,2.146 true 3.219,1.406 3.219,0.823 3.219,0.823 3.052,0.823 true 3.51,1.396 3.51,0.646 3.51,0.646 3.677,0.646 true 3.635,1.396 3.635,0.813 3.635,0.813 3.802,0.813 true 3.5,1.729 3.5,2.313 3.5,2.313 3.667,2.313 true 3.646,1.719 3.646,2.135 3.646,2.135 3.813,2.135 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.51,0.281 3.781,0.469 0.271,0.188 10 false A67 2.49,0.74 3.135,0.979 0.646,0.24 10 false CANH*b 2.51,2.073 3.156,2.313 0.646,0.24 10 false CANL*b 3.76,0.563 4.406,0.802 0.646,0.24 10 false CANH*b 3.875,0.729 4.521,0.969 0.646,0.24 10 false CANH*c 3.74,2.229 4.385,2.469 0.646,0.24 10 false CANL*b 3.896,2.052 4.542,2.292 0.646,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
*c to ECM - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) LG Brake booster with master cylinder assembly (skid control ECU)
(for Bus 2)
A67-7 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (skid control ECU)
(for Sub bus 15)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 15)
A67-10 (CANL) W



b.

Check the No. 1 CAN junction connector (instrument panel wire side).

i.

Connection diagram

C234761C51
3.417,0.25 3.823,0.479 0.406,0.229 3.51,1.729 3.51,2.146 3.51,2.146 3.344,2.146 true 3.51,1.406 3.51,0.823 3.51,0.823 3.344,0.823 true 3.792,1.396 3.792,0.646 3.792,0.646 3.625,0.646 true 3.802,1.729 3.802,2.313 3.802,2.313 3.635,2.313 true 3.938,1.396 3.938,0.813 3.938,0.813 4.104,0.813 true 3.948,1.719 3.948,2.135 3.948,2.135 4.115,2.135 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.469,0.281 3.896,0.49 0.427,0.208 10 false L132 2.802,0.76 3.448,1 0.646,0.24 10 false CANH*b 2.823,2.073 3.469,2.313 0.646,0.24 10 false CANL*b 3.073,0.583 3.719,0.823 0.646,0.24 10 false CANH*c 3.115,2.25 3.76,2.49 0.646,0.24 10 false CANL*c 4.177,0.74 4.823,0.979 0.646,0.24 10 false CANH*d 4.208,2.063 4.854,2.302 0.646,0.24 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
*c to No. 2 CAN Junction Connector *d Combination Meter Sub-assembly



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R No. 5 CAN junction connector
(for Sub bus 15)
L132-9 (CANL) Y
L132-5 (CANH) GR No. 2 CAN junction connector
(for Bus 2)
L132-11 (CANL) W
L132-6 (CANH) SB Combination meter sub-assembly
(for Bus 2)
L132-12 (CANL) G




NO. 2 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 2 CAN junction connector (instrument panel connector holder left side).

i.

Connection diagram

C214318C33
3.375,0.573 3.781,0.781 0.406,0.208 4.292,1.146 4.146,1.146 4.146,1.146 3.615,1.365 true 4.292,1.438 4.125,1.438 4.125,1.438 3.615,1.521 true 4.302,1.792 4.167,1.792 4.167,1.792 3.615,1.677 true 4.302,2.052 4.167,2.052 4.167,2.052 3.625,1.823 true 2.75,1.146 2.896,1.146 2.896,1.146 3.427,1.365 true 2.74,1.438 2.906,1.438 2.906,1.438 3.417,1.521 true 2.729,1.792 2.865,1.792 2.865,1.792 3.417,1.677 true 2.74,2.063 2.875,2.063 2.875,2.063 3.417,1.833 true 0.115,0.104 0.781,0.438 0.667,0.333 10 false *a 4.354,1.073 4.948,1.344 0.594,0.271 10 false CANL*b 4.365,1.344 5,1.594 0.635,0.25 10 false CANL*c 4.354,1.719 4.948,1.958 0.594,0.24 10 false CANL*d 4.365,1.969 5.063,2.281 0.698,0.313 10 false CANL*e 2.208,1.063 2.833,1.302 0.625,0.24 10 false CANH*b 2.198,1.354 2.833,1.635 0.635,0.281 10 false CANH*c 2.177,1.708 2.75,1.969 0.573,0.26 10 false CANH*d 2.188,1.979 2.802,2.219 0.615,0.24 10 false CANH*e 3.469,0.604 3.885,0.917 0.417,0.313 10 false L94
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to No. 3 CAN Junction Connector *d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) - -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-1 (CANH) GR No. 1 CAN junction connector
(for Bus 2)
L94-2 (CANL) W
L94-4 (CANH) B No. 3 CAN junction connector
(for Bus 2)
L94-5 (CANL) W
L94-7 (CANH) B Certification ECU (smart key ECU assembly)
(for Bus 2)
L94-8 (CANL) W
L94-10 (CANH) B Spiral cable with sensor sub-assembly (steering angle sensor)
(for Bus 2)
L94-11 (CANL) W



b.

Check the No. 2 CAN junction connector (instrument panel connector holder right side).

i.

Connection diagram

C214318C34
3.375,0.542 3.823,0.781 0.448,0.24 2.865,1.146 3.01,1.146 3.01,1.146 3.542,1.365 true 2.875,1.438 3.042,1.438 3.042,1.438 3.542,1.521 true 2.854,1.792 2.99,1.792 2.99,1.792 3.542,1.677 true 2.885,2.083 3.021,2.083 3.021,2.083 3.573,1.875 true 4.396,1.146 4.25,1.146 4.25,1.146 3.719,1.365 true 4.396,1.438 4.229,1.438 4.229,1.438 3.719,1.521 true 4.417,1.792 4.271,1.792 4.271,1.792 3.729,1.677 true 4.427,2.052 4.292,2.052 4.292,2.052 3.708,1.875 true 0.115,0.094 0.781,0.427 0.667,0.333 10 false *a 2.344,1.073 2.875,1.313 0.531,0.24 10 false CANL*b 2.333,1.354 2.896,1.615 0.563,0.26 10 false CANL*c 2.333,1.719 2.906,1.958 0.573,0.24 10 false CANL*d 2.344,2 2.948,2.198 0.604,0.198 10 false CANL*e 4.469,1.083 5.01,1.365 0.542,0.281 10 false CANH*b 4.469,1.375 5,1.656 0.531,0.281 10 false CANH*c 4.469,1.719 5.104,2.021 0.635,0.302 10 false CANH*d 4.479,1.979 5.094,2.271 0.615,0.292 10 false CANH*e 3.479,0.583 3.833,0.813 0.354,0.229 10 false L95
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Power Steering ECU Assembly
*c to Air Conditioning Amplifier Assembly *d to Airbag ECU Assembly
*e to Central Gateway ECU (Network Gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-3 (CANH) R Power steering ECU assembly
(for Bus 2)
L95-2 (CANL) W
L95-6 (CANH) B Air conditioning amplifier assembly
(for Bus 2)
L95-5 (CANL) W
L95-9 (CANH) B Airbag ECU assembly
(for Bus 2)
L95-8 (CANL) W
L95-12 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 2)
L95-11 (CANL) W




NO. 3 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 3 CAN junction connector (engine room main wire side).

i.

Connection diagram

C234761C70
3.417,0.25 3.823,0.479 0.406,0.229 3.219,1.719 3.219,2.135 3.219,2.135 3.052,2.135 true 3.219,1.406 3.219,0.823 3.219,0.823 3.052,0.823 true 3.354,1.406 3.354,0.823 3.354,0.823 3.521,0.823 true 3.365,1.719 3.365,2.135 3.365,2.135 3.531,2.135 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.51,0.281 3.781,0.469 0.271,0.188 10 false A68 2.49,0.74 3.135,0.979 0.646,0.24 10 false CANH*b 2.5,2.063 3.146,2.302 0.646,0.24 10 false CANL*b 3.583,0.76 4.229,1 0.646,0.24 10 false CANH*c 3.604,2.052 4.25,2.292 0.646,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b ECM
*c to Transmission Control ECU Assembly - -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) P ECM
(for Bus 2)
A68-7 (CANL) V
A68-2 (CANH) Y Transmission control ECU assembly
(for Bus 2)
A68-8 (CANL) BR



b.

Check the No. 3 CAN junction connector (instrument panel wire side).

i.

Connection diagram

C234761C53
3.417,0.25 3.823,0.479 0.406,0.229 3.646,1.729 3.646,2.146 3.646,2.146 3.479,2.146 true 3.646,1.406 3.646,0.823 3.646,0.823 3.479,0.823 true 3.802,1.396 3.802,0.646 3.802,0.646 3.969,0.646 true 3.948,1.396 3.948,0.813 3.948,0.813 4.115,0.813 true 3.792,1.729 3.792,2.313 3.792,2.313 3.958,2.313 true 3.948,1.719 3.948,2.135 3.948,2.135 4.115,2.135 true 0.115,0.125 0.49,0.667 0.375,0.542 10 false *a 3.49,0.281 3.906,0.479 0.417,0.198 10 false L133 2.917,0.75 3.563,0.99 0.646,0.24 10 false CANH*b 2.948,2.073 3.594,2.313 0.646,0.24 10 false CANL*b 4.042,0.573 4.688,0.813 0.646,0.24 10 false CANH*c 4.198,0.729 4.844,0.969 0.646,0.24 10 false CANH*d 4.031,2.229 4.677,2.469 0.646,0.24 10 false CANL*c 4.198,2.052 4.844,2.292 0.646,0.24 10 false CANL*d
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to Main body ECU (Multiplex Network Body ECU) *d to No. 2 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Hybrid vehicle control ECU
(for Bus 2)
L133-10 (CANL) P
L133-5 (CANH) SB Main body ECU (multiplex network body ECU)
(for Bus 2)
L133-11 (CANL) W
L133-6 (CANH) B No. 2 CAN junction connector
(for Bus 2)
L133-12 (CANL) W




NO. 4 CAN JUNCTION CONNECTOR


a.

Check the No. 4 CAN junction connector.

HINT:
·

Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.

·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



i.

Connection diagram

C423692C13
0.792,1.104 0.969,1.104 0.969,1.104 1.323,1.354 true 0.844,1.719 1.031,1.719 1.031,1.719 1.323,1.563 true 0.542,0.656 0.854,0.854 0.313,0.198 10 false *a 0.448,1.667 1.052,1.875 0.604,0.208 10 false CANH 0.438,1.063 0.948,1.271 0.51,0.208 10 false CANL 2.781,0.646 3.094,0.844 0.313,0.198 10 false *b
*a Vehicle wire harness connector
connected to CAN junction connector
*b Rear view of wire harness connector
(to No. 4 CAN Junction Connector)




b.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L203-1 (CANH) B Millimeter wave radar sensor assembly*1
(for Bus 5)
L203-2 (CANL) BE
L199-1 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
L199-2 (CANL) P
L198-1 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
L198-2 (CANL) V
L185-1 (CANH) B Forward recognition camera*1
(for Bus 5)
L185-2 (CANL) W
L184-1 (CANH) B Hybrid vehicle control ECU
(for Bus 5)
L184-2 (CANL) G
L183-1 (CANH) B Parking assist ECU*2
(for Bus 5)
L183-2 (CANL) L
L182-1 (CANH) B Driving support ECU assembly*1
(for Bus 5)
L182-2 (CANL) R

·

*1: w/ Toyota Safety Sense

·

*2: w/ Intelligent Parking Assist System




NO. 5 CAN JUNCTION CONNECTOR


a.

Check the No. 5 CAN junction connector (instrument panel connector holder left side).

i.

Connection diagram

C234761C54
2.271,1.333 2.677,1.563 0.406,0.229 3.365,1.406 3.365,0.74 3.365,0.74 2.948,0.74 true 3.635,1.396 3.635,0.729 3.635,0.729 4.052,0.729 true 0.135,0.125 0.51,0.667 0.375,0.542 10 false *a 2.344,1.385 2.688,1.583 0.344,0.198 10 false L101 4.167,0.667 4.813,0.906 0.646,0.24 10 false CANL*b 2.396,0.677 3.042,0.917 0.646,0.24 10 false CANH*b
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L101-2 (CANH) R No. 1 CAN junction connector
(for Sub bus 15)
L101-4 (CANL) Y



b.

Check the No. 5 CAN junction connector (instrument panel connector holder right side).

i.

Connection diagram

C234761C55
2.271,1.406 2.677,1.635 0.406,0.229 3.5,1.406 3.5,0.698 3.5,0.698 3.323,0.698 true 3.792,1.406 3.792,0.698 3.792,0.698 3.969,0.698 true 0.125,0.115 0.5,0.656 0.375,0.542 10 false *a 2.333,1.448 2.708,1.844 0.375,0.396 10 false L102 4.063,0.625 4.708,0.865 0.646,0.24 10 false CANH*b 2.813,0.625 3.458,0.865 0.646,0.24 10 false CANL*b
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L102-5 (CANH) B Hybrid vehicle control ECU
(for Sub bus 15)
L102-3 (CANL) W




NO. 6 CAN JUNCTION CONNECTOR


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C380534C80
0.833,1.323 1.313,1.583 0.479,0.26 3.417,1.427 3.417,0.563 3.417,0.563 3.25,0.563 true 3.583,1.438 3.583,0.323 3.583,0.323 3.417,0.323 true 3.417,1.688 3.417,2.24 3.417,2.24 3.25,2.24 true 3.594,1.698 3.594,2.417 3.594,2.417 3.427,2.417 true 3.76,1.427 3.76,0.635 3.76,0.635 3.927,0.635 true 3.76,1.698 3.76,2.198 3.76,2.198 3.927,2.198 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.917,1.365 1.313,1.573 0.396,0.208 10 false L204 2.865,0.24 3.427,0.49 0.563,0.25 10 false CANH*b 4,0.552 4.906,0.833 0.906,0.281 10 false CANH*c*d 2.885,2.323 3.448,2.573 0.563,0.25 10 false CANL*b 4,2.115 4.885,2.385 0.885,0.271 10 false CANL*c*d 2.688,0.49 3.333,0.74 0.646,0.25 10 false CANH*b 2.75,2.146 3.313,2.396 0.563,0.25 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Navigation Receiver Assembly
(for Navigation Receiver Type)
*d to Radio and Display Receiver Assembly
(for Radio and Display Type)



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L204-5 (CANH) R Central gateway ECU (network gateway ECU)
(for Bus 3)
L204-16 (CANL) W
L204-6 (CANH) GR Central gateway ECU (network gateway ECU)
(for Bus 3)
L204-17 (CANL) W
L204-7 (CANH) B Navigation receiver assembly*1
(for Bus 3)
L204-18 (CANL) W
L204-7 (CANH) B Radio and display receiver assembly*2
(for Bus 3)
L204-18 (CANL) W

·

*1: for Navigation Receiver Type

·

*2: for Radio and Display Type





DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C292402C13
3.354,0.052 3.75,0.344 0.396,0.292 3.479,0.708 3.115,0.271 3.115,0.271 2.979,0.271 true 3.833,1.24 3.281,1.625 3.281,1.625 3.135,1.625 true 4.698,1.573 4.542,1.573 4.542,1.573 4.208,1.219 true 4.396,0.24 4.25,0.24 4.25,0.24 3.844,0.719 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *1 3.458,0.115 3.771,0.313 0.313,0.198 10 false L61 2.708,0.177 3.021,0.375 0.313,0.198 10 false CG 2.719,1.531 3.333,1.729 0.615,0.198 10 false CANL 4.771,1.479 5.229,1.677 0.458,0.198 10 false BAT 4.469,0.146 5.083,0.344 0.615,0.198 10 false CANH
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L61-6 (CANH) - L61-14 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L61-6 (CANH) - L61-4 (CG) G - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-14 (CANL) - L61-4 (CG) W - G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-6 (CANH) - L61-16 (BAT) G - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L61-14 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C349819C53
1.083,1.281 1.5,1.552 0.417,0.271 3.615,2.51 3.448,2.51 3.448,2.51 3.448,1.427 true 2.99,1.302 2.99,0.771 2.99,0.771 2.865,0.771 true 3.135,2.24 3.281,2.24 3.281,2.24 3.281,1.438 true 3.542,1.375 3.542,0.51 3.542,0.51 3.698,0.51 true 2.792,1.979 2.948,1.979 2.948,1.979 2.948,1.438 true 3.208,2.438 3.365,2.438 3.365,2.438 3.365,1.438 true 3.24,1.292 3.24,0.583 3.24,0.583 3.083,0.583 true 3.625,1.385 3.625,0.667 3.625,0.667 3.781,0.667 true 3.885,2.354 3.719,2.354 3.719,2.354 3.719,1.438 true 3.958,2.188 3.792,2.188 3.792,2.188 3.792,1.427 true 4.042,2 3.875,2 3.875,2 3.875,1.427 true 3.917,1.292 3.917,0.854 3.917,0.854 4.073,0.854 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.677,0.531 3.167,0.708 0.49,0.177 10 false CA3H 2.458,0.719 2.948,0.896 0.49,0.177 10 false CAXH 2.417,1.927 2.906,2.104 0.49,0.177 10 false CAXL 3.688,2.448 4.177,2.625 0.49,0.177 10 false CAYH 2.792,2.375 3.281,2.552 0.49,0.177 10 false CAYL 3.76,0.438 4.25,0.615 0.49,0.177 10 false CA4H 4.135,0.792 4.688,1.01 0.552,0.219 10 false CA6L 4.031,2.125 4.521,2.302 0.49,0.177 10 false CA5H 3.969,2.292 4.521,2.51 0.552,0.219 10 false CA5L 1.156,1.344 1.604,1.604 0.448,0.26 10 false L192 4.115,1.938 4.604,2.115 0.49,0.177 10 false CA6H 3.844,0.604 4.396,0.823 0.552,0.219 10 false CA4L 2.75,2.156 3.24,2.333 0.49,0.177 10 false CA3L
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C361640C44
0.906,1.729 1.344,1.958 0.438,0.229 2.021,1.208 2.271,1.208 2.271,1.208 2.271,1.708 true 2.729,0.969 2.979,0.969 2.979,0.969 2.979,1.719 true 2.823,2.625 3.073,2.625 3.073,2.625 3.073,2 true 2.969,2.844 3.219,2.844 3.219,2.844 3.219,2.01 true 5.135,1.156 4.885,1.156 4.885,1.156 4.885,1.719 true 3.26,0.75 3.51,0.75 3.51,0.75 3.51,1.917 true 3.406,0.51 3.656,0.51 3.656,0.51 3.656,1.927 true 3.115,3.021 3.365,3.021 3.365,3.021 3.365,2.021 true 4.042,3.156 3.792,3.156 3.792,3.156 3.792,2 true 4.177,2.99 3.927,2.99 3.927,2.99 3.927,2.01 true 4.323,2.813 4.073,2.813 4.073,2.813 4.073,2 true 5.073,2.635 4.823,2.635 4.823,2.635 4.823,2 true 4.448,0.792 4.198,0.792 4.198,0.792 4.198,1.719 true 4.948,0.969 4.698,0.969 4.698,0.969 4.698,1.729 true 0.979,1.76 1.531,2.021 0.552,0.26 10 false L192 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.615,1.135 2.167,1.396 0.552,0.26 10 false BATT 2.333,0.906 2.885,1.167 0.552,0.26 10 false CA6L 2.406,2.552 2.958,2.813 0.552,0.26 10 false CA6H 2.552,2.76 3.104,3.021 0.552,0.26 10 false CA5H 5.229,1.073 5.781,1.333 0.552,0.26 10 false GND 4.521,0.719 5.073,0.979 0.552,0.26 10 false CA3H 2.99,0.438 3.542,0.698 0.552,0.26 10 false CA4H 2.875,0.688 3.427,0.948 0.552,0.26 10 false CA4L 2.719,2.948 3.271,3.208 0.552,0.26 10 false CA5L 4.406,2.719 4.958,2.979 0.552,0.26 10 false CA3L 4.271,2.896 4.823,3.156 0.552,0.26 10 false CAYL 4.135,3.073 4.688,3.333 0.552,0.26 10 false CAYH 5.156,2.552 5.708,2.813 0.552,0.26 10 false CAXL 5.031,0.896 5.583,1.156 0.552,0.26 10 false CAXH
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
V Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-14 (CA6H) - L192-5 (CA6L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
L192-14 (CA6H) - L192-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-5 (CA6L) - L192-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-14 (CA6H) - L192-1 (BATT) G - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-5 (CA6L) - L192-1 (BATT) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-18 (CA4H) - L192-17 (CA4L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L192-18 (CA4H) - L192-10 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-17 (CA4L) - L192-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-18 (CA4H) - L192-1 (BATT) L - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-17 (CA4L) - L192-1 (BATT) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-6 (CA3H) - L192-19 (CAYH) R - GR HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-21 (CA3L) - L192-20 (CAYL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-6 (CA3H) - L192-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-21 (CA3L) - L192-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-6 (CA3H) - L192-1 (BATT) R - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-21 (CA3L) - L192-1 (BATT) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L192-15 (CA5H) - L192-9 (CAXH) B - B HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-16 (CA5L) - L192-24 (CAXL) V - P LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-15 (CA5H) - L192-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-16 (CA5L) - L192-10 (GND) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-15 (CA5H) - L192-1 (BATT) B - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-16 (CA5L) - L192-1 (BATT) V - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU


Refer to Terminals of ECU (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C355784C01
2.51,3.031 2.865,3.292 0.354,0.26 2.708,2.344 2.896,1.885 2.896,1.885 2.979,1.885 true 2.635,2.344 2.292,2.01 2.292,2.01 2.125,2.01 true 2.146,2.958 2.469,2.583 true 2.104,2.229 2.458,2.49 true 2.115,2.396 2.406,2.51 true 2.104,2.667 2.417,2.573 true 3.031,1.802 3.406,1.99 0.375,0.188 10 false BATT 0.156,0.104 0.552,0.333 0.396,0.229 10 false *a 1.823,1.938 2.198,2.125 0.375,0.188 10 false E12 1.74,2.896 2.198,3.083 0.458,0.188 10 false CA3N 1.698,2.604 2.156,2.792 0.458,0.188 10 false CA3P 1.719,2.333 2.177,2.521 0.458,0.188 10 false CA1H 1.729,2.156 2.188,2.344 0.458,0.188 10 false CA1L 2.625,3.073 2.948,3.281 0.323,0.208 10 false L6
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the L6 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-25 (CA1H) - L6-24 (CA1L) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L6-25 (CA1H) - L6-4 (E12) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-24 (CA1L) - L6-4 (E12) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-25 (CA1H) - L6-3 (BATT) V - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-24 (CA1L) - L6-3 (BATT) P - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L6-31 (CA3P) - L6-4 (E12) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-30 (CA3N) - L6-4 (E12) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-31 (CA3P) - L6-3 (BATT) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-30 (CA3N) - L6-3 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



d.
A253458C80
1.802,1.417 2.25,1.656 0.448,0.24 2.542,1.417 3,1.646 0.458,0.229 1.396,2.333 1.771,2.333 true 1.521,2.646 1.823,2.333 true 3.01,2.781 2.844,2.125 true 1.271,1.99 1.792,2.115 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.958,1.448 2.354,1.646 0.396,0.198 10 false L5 2.698,1.458 3.01,1.688 0.313,0.229 10 false L6 0.99,2.271 1.448,2.49 0.458,0.219 10 false CA2L 1.042,1.917 1.354,2.073 0.313,0.156 10 false E1 2.865,2.833 3.281,2.99 0.417,0.156 10 false BATT 1.125,2.594 1.583,2.813 0.458,0.219 10 false CA2H
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the L5 hybrid vehicle control ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 5 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L5-34 (CA2H) - L5-35 (CA2L) B - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L5-34 (CA2H) - L5-6 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L5-35 (CA2L) - L5-6 (E1) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L5-34 (CA2H) - L6-3 (BATT) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L5-35 (CA2L) - L6-3 (BATT) G - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A57 and D28 ECM connectors.

C188791C02
0.479,1.479 0.792,1.708 0.313,0.229 3.052,1.51 3.396,1.719 0.344,0.208 5.104,1.833 5.104,2.417 5.104,2.417 5.354,2.417 true 1.885,1.354 1.885,0.688 1.885,0.688 1.719,0.688 true 1.969,1.354 1.969,0.688 1.969,0.688 2.135,0.688 true 1.635,1.479 1.635,0.979 1.635,0.979 1.469,0.979 true 1.885,1.448 1.885,2.281 1.885,2.281 1.719,2.281 true 1.958,1.458 1.958,2.292 1.958,2.292 2.125,2.292 true 0.177,0.167 0.635,0.521 0.458,0.354 10 false *a 3.104,1.531 3.406,1.708 0.302,0.177 10 false D28 2.208,0.615 2.656,0.781 0.448,0.167 10 false CANL 2.208,2.208 2.656,2.375 0.448,0.167 10 false CANH 1.083,0.906 1.479,1.073 0.396,0.167 10 false BATT 5.427,2.333 5.677,2.5 0.25,0.167 10 false E1 0.521,1.51 0.854,1.688 0.333,0.177 10 false A57 1.281,2.198 1.688,2.375 0.406,0.177 10 false CANP 1.26,0.615 1.667,0.792 0.406,0.177 10 false CANN
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-13 (CANH) - D28-104 (E1) P - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-5 (CANL) - D28-104 (E1) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-13 (CANH) - A57-20 (BATT) P - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-5 (CANL) - A57-20 (BATT) V - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-12 (CANP) - D28-104 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-4 (CANN) - D28-104 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-12 (CANP) - A57-20 (BATT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-4 (CANN) - A57-20 (BATT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TRANSMISSION CONTROL ECU ASSEMBLY


Refer to Terminals of ECU (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C210430C02
0.438,1.344 0.854,1.615 0.417,0.271 0.438,3.427 0.854,3.698 0.417,0.271 2.083,3.75 2.083,4.25 2.083,4.25 2.25,4.25 true 2.167,1.75 2.167,2.25 2.167,2.25 2.333,2.25 true 2.063,1.75 2.063,2.25 2.063,2.25 1.896,2.25 true 1.219,1.333 1.219,0.75 1.219,0.75 1.052,0.75 true 0.073,0.104 0.427,0.479 0.354,0.375 10 false *a 0.531,1.396 0.958,1.74 0.427,0.344 10 false A24 0.531,3.49 0.948,3.823 0.417,0.333 10 false A23 2.438,2.167 2.844,2.344 0.406,0.177 10 false CA1H 1.5,2.188 1.885,2.365 0.385,0.177 10 false CA1L 2.313,4.177 2.688,4.354 0.375,0.177 10 false BATT 0.823,0.688 1.052,0.885 0.229,0.198 10 false E1
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


Disconnect the A23 and A24 transmission control ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-16 (CA1H) - A24-15 (CA1L) Y - BR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A24-16 (CA1H) - A24-1 (E1) Y - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-15 (CA1L) - A24-1 (E1) BR - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-16 (CA1H) - A23-15 (BATT) Y - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A24-15 (CA1L) - A23-15 (BATT) BR - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.

C334686C05
1.615,0.698 2.083,0.958 0.469,0.26 4.323,0.719 4.323,0.146 4.323,0.146 4.521,0.146 true 3.521,1.042 3.521,1.469 3.521,1.469 3.333,1.469 true 3.594,1.052 3.594,1.646 3.594,1.646 3.406,1.646 true 3.771,1.052 3.771,1.646 3.771,1.646 3.938,1.646 true 3.844,1.042 3.844,1.469 3.844,1.469 4.042,1.469 true 4.375,0.917 4.917,0.917 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.74,0.75 2.052,0.948 0.313,0.198 10 false A58 4.594,0.073 4.906,0.271 0.313,0.198 10 false BS 2.969,1.406 3.417,1.615 0.448,0.208 10 false CA2L 3,1.573 3.469,1.76 0.469,0.188 10 false CA2H 4.115,1.396 4.563,1.604 0.448,0.208 10 false CA1L 4.01,1.583 4.479,1.75 0.469,0.167 10 false CA1H 5,0.844 5.448,1.052 0.448,0.208 10 false GND
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-37 (CA1H) - A58-38 (CA1L) LG - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-37 (CA1H) - A58-28 (GND) LG - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-38 (CA1L) - A58-28 (GND) L - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-37 (CA1H) - A58-15 (BS) LG - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-38 (CA1L) - A58-15 (BS) L - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-35 (CA2H) - A58-28 (GND) P - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-34 (CA2L) - A58-28 (GND) V - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-35 (CA2H) - A58-15 (BS) P - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-34 (CA2L) - A58-15 (BS) V - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


Refer to Terminals of ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L16 airbag ECU assembly connector.

C292356C15
1.51,0.177 1.938,0.375 0.427,0.198 4.885,0.156 5.292,0.406 0.406,0.25 1.51,1.021 1.51,0.521 1.51,0.521 1.344,0.521 true 1.292,1.615 1.417,1.615 1.417,1.615 1.417,1.292 true 1.688,1.313 1.688,1.625 1.688,1.625 1.813,1.625 true 5.708,1.375 5.708,1.625 5.708,1.625 5.844,1.625 true 0.365,0.083 0.677,0.281 0.313,0.198 10 false *a 1.594,0.188 2.052,0.385 0.458,0.198 10 false L16 0.917,0.448 1.531,0.646 0.615,0.198 10 false CANH 0.885,1.542 1.5,1.74 0.615,0.198 10 false CANL 1.896,1.542 2.208,1.74 0.313,0.198 10 false E1 3.677,0.104 3.99,0.302 0.313,0.198 10 false *1 4.99,0.198 5.302,0.396 0.313,0.198 10 false L61 5.917,1.542 6.375,1.74 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L16-13 (CANH) - L16-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L16-13 (CANH) - L16-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-22 (CANL) - L16-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-13 (CANH) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L16-22 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L201 main body ECU (multiplex network body ECU) connector.

C304289C07
0.531,0.729 0.979,0.99 0.448,0.26 3.344,0.719 3.792,0.979 0.448,0.26 6.042,1.542 5.771,1.542 5.771,1.542 5.771,1.125 true 2.26,0.865 2.26,0.167 2.26,0.167 2.469,0.167 true 5.052,0.563 5.052,0.146 5.052,0.146 4.802,0.146 true 2.167,0.875 2.167,0.177 2.167,0.177 1.917,0.177 true 0.844,0.188 1.281,0.448 0.438,0.26 10 false *a 3.667,0.083 4.104,0.344 0.438,0.26 10 false *1 3.479,0.76 3.917,1.021 0.438,0.26 10 false L61 1.521,0.094 2.01,0.417 0.49,0.323 10 false CANL 0.625,0.771 1.115,1.094 0.49,0.323 10 false L201 2.573,0.083 3.063,0.406 0.49,0.323 10 false CANH 4.542,0.073 4.979,0.333 0.438,0.26 10 false CG 6.115,1.458 6.552,1.719 0.438,0.26 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L201-14 (CANH) - L201-13 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L201-14 (CANH) - L61-4 (CG) SB - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L201-13 (CANL) - L61-4 (CG) W- G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L201-14 (CANH) - L61-16 (BAT) SB - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L201-13 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C164504C06
3.281,0.167 3.76,0.385 0.479,0.219 3.167,1.531 3.521,1.531 3.521,1.531 3.521,1.125 true 3.875,1.542 3.656,1.542 3.656,1.542 3.656,1.135 true 3.927,1.469 4.75,1.729 0.823,0.26 10 false CANL 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.771,1.479 3.5,1.708 0.729,0.229 10 false CANH 3.385,0.208 3.698,0.406 0.313,0.198 10 false L51
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C185765C86
1.552,1.115 1.979,1.406 0.427,0.292 1.646,2.542 1.646,3.125 1.646,3.125 1.396,3.125 true 1.875,2.521 1.875,3.146 1.875,3.146 2.146,3.146 true 2.354,2.552 2.354,2.885 2.354,2.885 2.521,2.885 true 1.385,2.552 1.385,2.885 1.385,2.885 1.219,2.885 true 0.198,0.208 0.521,0.521 0.323,0.313 10 false *a 1,3.042 1.427,3.271 0.427,0.229 10 false CANL 2.219,3.052 2.719,3.302 0.5,0.25 10 false CANH 1.646,1.198 1.938,1.406 0.292,0.208 10 false L51 2.615,2.802 3.115,3.052 0.5,0.25 10 false BAT 0.896,2.813 1.323,3.042 0.427,0.229 10 false ESS
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))


Disconnect the L51 spiral cable with sensor sub-assembly (steering angle sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L51-4 (CANH) - L51-3 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L51-4 (CANH) - L51-2 (ESS) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-3 (CANL) - L51-2 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-4 (CANH) - L51-6 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L51-3 (CANL) - L51-6 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A27 and L54 power steering ECU assembly connectors.

C188801C04
2.094,0.427 2.479,0.688 0.385,0.26 4.708,0.708 5.052,0.948 0.344,0.24 1.896,1.875 1.479,1.875 true 1.958,2.083 1.958,2.5 1.958,2.5 2.208,2.5 true 4.958,1.625 5.365,1.625 true 4.958,1.917 5.365,1.917 true 0.167,0.146 2.563,0.5 2.396,0.354 10 false *a 2.271,2.406 2.719,2.573 0.448,0.167 10 false CANL 1.042,1.792 1.49,1.958 0.448,0.167 10 false CANH 5.469,1.531 5.792,1.698 0.323,0.167 10 false PIG 5.448,1.833 5.875,2 0.427,0.167 10 false PGND 2.177,0.49 2.5,0.667 0.323,0.177 10 false L54 4.75,0.74 5.073,0.917 0.323,0.177 10 false A27
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L54-1 (CANH) - L54-7 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L54-1 (CANH) - A27-2 (PGND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-7 (CANL) - A27-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-1 (CANH) - A27-1 (PIG) R - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L54-7 (CANL) - A27-1 (PIG) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L195 and L197 certification ECU (smart key ECU assembly) connectors.

C289262C09
1.865,0.292 2.323,0.563 0.458,0.271 4.615,0.323 5.063,0.573 0.448,0.25 2.125,0.844 2.26,0.844 2.26,0.844 2.26,1.521 true 5.458,0.917 5.313,0.917 5.313,0.917 5.313,1.365 true 4.281,2.063 4.396,2.063 4.396,2.063 4.396,1.729 true 2.521,0.844 2.354,0.844 2.354,0.844 2.354,1.521 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.938,0.344 2.396,0.542 0.458,0.198 10 false L197 4.688,0.354 5.146,0.552 0.458,0.198 10 false L195 1.677,0.771 2.292,0.969 0.615,0.198 10 false CANH 2.625,0.771 3.24,0.969 0.615,0.198 10 false CANL 5.563,0.833 5.875,1.031 0.313,0.198 10 false +B 4.094,2 4.25,2.198 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L197-14 (CANH) - L197-15 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L197-14 (CANH) - L195-11 (E) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L197-15 (CANL) - L195-11 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L197-14 (CANH) - L195-2 (+B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L197-15 (CANL) - L195-2 (+B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L35 and L167 radio and display receiver assembly connectors.

C240506C77
0.594,1.49 0.99,1.729 0.396,0.24 3.854,1.469 4.281,1.708 0.427,0.24 1.854,0.552 2.01,0.552 2.01,0.552 2.01,1.688 true 2.333,0.552 2.115,0.552 2.115,0.552 2.115,1.688 true 5.792,0.521 5.635,0.521 5.635,0.521 5.635,1.5 true 5.188,2.281 5.021,2.281 5.021,2.281 5.021,1.885 true 0.125,0.146 0.302,0.323 0.177,0.177 10 false *a 2.375,0.448 2.813,0.625 0.438,0.177 10 false CANL 1.448,0.448 1.885,0.625 0.438,0.177 10 false CANH 5.854,0.417 6.156,0.594 0.302,0.177 10 false +B1 5.229,2.177 5.677,2.365 0.448,0.188 10 false GND1 0.667,1.51 1.156,1.823 0.49,0.313 10 false L35 3.906,1.51 4.563,2.01 0.656,0.5 10 false L167
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L35-9 (CANH) - L35-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L35-9 (CANH) - L167-7 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-10 (CANL) - L167-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-9 (CANH) - L167-4 (+B1) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L35-10 (CANL) - L167-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


Refer to Terminals of ECU (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L38 and L171 navigation receiver assembly connectors.

C240506C78
0.594,1.49 0.99,1.729 0.396,0.24 3.854,1.469 4.281,1.708 0.427,0.24 1.854,0.552 2.01,0.552 2.01,0.552 2.01,1.688 true 2.333,0.552 2.115,0.552 2.115,0.552 2.115,1.688 true 5.792,0.521 5.635,0.521 5.635,0.521 5.635,1.5 true 5.188,2.281 5.021,2.281 5.021,2.281 5.021,1.885 true 0.125,0.146 0.302,0.323 0.177,0.177 10 false *a 2.375,0.448 2.813,0.625 0.438,0.177 10 false CANL 1.448,0.448 1.885,0.625 0.438,0.177 10 false CANH 5.854,0.417 6.156,0.594 0.302,0.177 10 false +B1 5.229,2.177 5.677,2.365 0.448,0.188 10 false GND1 0.667,1.51 1.156,1.823 0.49,0.313 10 false L38 3.927,1.51 4.583,2.01 0.656,0.5 10 false L171
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L38-9 (CANH) - L38-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L38-9 (CANH) - L171-7 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-10 (CANL) -L171-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-9 (CANH) - L171-4 (+B1) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L38-10 (CANL) - L171-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER SUB-ASSEMBLY


Refer to Terminals of ECU (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L27 combination meter sub-assembly connector.

C188799C24
1.719,1.75 2.083,2 0.365,0.25 4.469,1.958 4.469,1.292 4.469,1.292 4.635,1.292 true 4.365,1.938 4.365,1.104 4.365,1.104 4.531,1.104 true 2.698,1.948 2.698,1.281 2.698,1.281 2.531,1.281 true 3.615,1.938 3.115,1.021 3.115,1.021 2.948,1.021 true 0.219,0.177 0.385,0.344 0.167,0.167 10 false *a 4.708,1.208 5.156,1.375 0.448,0.167 10 false CANL 4.646,1.01 5.094,1.177 0.448,0.167 10 false CANH 2.354,1.198 2.531,1.365 0.177,0.167 10 false B 2.646,0.948 3.073,1.115 0.427,0.167 10 false ES 1.781,1.771 2.104,1.948 0.323,0.177 10 false L27
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) SB - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L27-19 (CANH) - L27-11 (ES) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-20 (CANL) - L27-11 (ES) G - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-19 (CANH) - L27-1 (B) SB - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L27-20 (CANL) - L27-1 (B) G - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L17 air conditioning amplifier assembly connector.

C292365C11
2.573,0.25 2.99,0.552 0.417,0.302 3.729,1.229 4.521,0.688 4.521,0.688 4.677,0.688 true 3.625,1.229 4.448,0.417 4.448,0.417 4.594,0.417 true 3.906,1.24 4.688,0.927 4.688,0.927 4.802,0.927 true 2.375,1.385 2.635,1.385 true 2.667,0.313 3.125,0.51 0.458,0.198 10 false L17 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.188,1.313 2.344,1.51 0.156,0.198 10 false B 4.875,0.844 5.333,1.042 0.458,0.198 10 false GND 4.688,0.323 5.302,0.521 0.615,0.198 10 false CANH 4.76,0.594 5.375,0.792 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L17-11 (CANH) - L17-12 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L17-11 (CANH) - L17-14 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-12 (CANL) - L17-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-11 (CANH) - L17-21 (B) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L17-12 (CANL) - L17-21 (B) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L205 driving support ECU assembly connector.

C345994C13
4.927,0.135 5.365,0.417 0.438,0.281 0.198,0.813 0.635,1.094 0.438,0.281 6.01,1.521 5.792,1.521 5.792,1.521 5.792,1.198 true 3.271,0.323 3.052,0.323 3.052,0.323 3.052,0.865 true 2.677,0.323 2.938,0.323 2.938,0.323 2.938,0.865 true 2.552,1.542 2.813,1.542 2.813,1.542 2.813,1.094 true 5.042,0.188 5.5,0.385 0.458,0.198 10 false L61 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a 3.958,0.083 4.271,0.281 0.313,0.198 10 false *1 0.271,0.865 0.729,1.063 0.458,0.198 10 false L205 6.083,1.438 6.542,1.635 0.458,0.198 10 false BAT 3.333,0.24 3.948,0.438 0.615,0.198 10 false CA2L 2.26,0.229 2.875,0.427 0.615,0.198 10 false CA2H 2.198,1.448 2.656,1.646 0.458,0.198 10 false GND
*1 DLC3 - -
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L205-10 (CA2H) - L205-11 (CA2L) B - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L205-10 (CA2H) - L205-28 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L205-11 (CA2L) - L205-28 (GND) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L205-10 (CA2H) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L205-11 (CA2L) - L61-16 (BAT) R - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Intelligent Parking Assist System)


Refer to Terminals of ECU (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C242511C01
2.115,0.271 2.625,0.51 0.51,0.24 1.448,2.667 1.948,2.906 0.5,0.24 2.625,2.781 2.458,2.781 2.458,2.781 2.458,3.365 true 0.75,2.75 0.917,2.75 0.917,2.75 0.917,3.333 true 2.427,1.896 2.594,1.896 2.594,1.896 2.594,1.479 true 2.875,1.896 2.708,1.896 2.708,1.896 2.708,1.479 true 0.073,0.063 0.281,0.26 0.208,0.198 10 false *a 2.25,0.302 2.521,0.479 0.271,0.177 10 false L65 1.573,2.698 1.844,2.875 0.271,0.177 10 false L64 2.052,1.813 2.448,1.969 0.396,0.156 10 false CANL 2.927,1.813 3.344,2.052 0.417,0.24 10 false CANH 2.698,2.698 3.115,2.854 0.417,0.156 10 false GND1 0.51,2.677 0.792,2.906 0.281,0.229 10 false +B
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the L64 and L65 parking assist ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-40 (CANH) - L65-39 (CANL) B - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L65-40 (CANH) - L64-4 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L65-39 (CANL) - L64-4 (GND1) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L65-40 (CANH) - L64-1 (+B) B - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L65-39 (CANL) - L64-1 (+B) L - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A91 millimeter wave radar sensor assembly connector.

C333371C22
0.875,0.802 1.396,1.063 0.521,0.26 4.917,0.115 5.438,0.375 0.521,0.26 2.74,0.24 2.458,0.24 2.458,0.24 2.458,0.813 true 2,0.24 2.313,0.24 2.313,0.24 2.313,0.813 true 1.448,0.521 1.615,0.521 1.615,0.521 2.115,0.854 true 6.083,1.583 5.802,1.583 5.802,1.583 5.802,1.188 true 0.167,0.073 0.479,0.229 0.313,0.156 10 false *a 3.771,0.135 4.083,0.292 0.313,0.156 10 false *1 5.052,0.167 5.365,0.323 0.313,0.156 10 false L61 6.156,1.49 6.469,1.646 0.313,0.156 10 false BAT 0.99,0.448 1.542,0.667 0.552,0.219 10 false SGND 1.01,0.854 1.563,1.073 0.552,0.219 10 false A91 2.792,0.156 3.344,0.375 0.552,0.219 10 false CA2H 1.604,0.156 2.156,0.375 0.552,0.219 10 false CA2L
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A91-3 (CA2H) - A91-2 (CA2L) B - BR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A91-3 (CA2H)- A91-1 (SGND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A91-2 (CA2L) - A91-1 (SGND) BR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A91-3 (CA2H) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A91-2 (CA2L) - L61-16 (BAT) BR - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>TERMINALS OF ECU).

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C287064C23
1.469,2.667 1.865,2.906 0.396,0.24 1.469,0.417 1.865,0.656 0.396,0.24 2.854,4.406 2.646,4.406 2.646,4.406 2.458,4.052 true 1.906,1.5 1.906,0.75 1.906,0.75 2.073,0.75 true 1.573,2.25 1.74,2.25 1.74,2.25 1.74,1.833 true 2.073,2.26 1.906,2.26 1.906,2.26 1.906,1.844 true 0.219,0.156 0.552,0.479 0.333,0.323 10 false *a 0.229,2.531 0.563,2.854 0.333,0.323 10 false *1 2.146,0.677 2.677,0.917 0.531,0.24 10 false CA1P 2.146,2.177 2.656,2.417 0.51,0.24 10 false CA1N 2.906,4.313 3.365,4.573 0.458,0.26 10 false BAT 1.542,0.448 1.927,0.719 0.385,0.271 10 false U15 1.583,2.698 1.969,2.969 0.385,0.271 10 false L61 1.25,2.188 1.771,2.469 0.521,0.281 10 false GND
*1 DLC3
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the U15 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U15-5 (CA1P) - U15-11 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
U15-5 (CA1P) - U15-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
U15-11 (CA1N) - U15-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
U15-5 (CA1P) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
U15-11 (CA1N) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher