When the brakes are applied by the dynamic radar cruise control system, the skid control ECU (brake booster with master cylinder assembly) operates the stop light switch assembly (stop light control relay) to illuminate the stop lights.
If the hybrid vehicle control ECU receives a stop light control relay malfunction signal from the skid control ECU (brake booster with master cylinder assembly), DTC P0571 is stored.
When the brake pedal is depressed, the stop light switch assembly sends a signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to the terminal STP. When the brake is applied, voltage is normally applied to the terminal STP of the hybrid vehicle control ECU through the STOP fuse and stop light switch assembly, and the hybrid vehicle control ECU turns the dynamic radar cruise control system off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0571 | Brake Switch "A" Circuit | Condition 1:
·
While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU detects the stop light control relay error signal from the skid control ECU for approximately 0.5 seconds or more. Condition 2:
·
While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, voltage of the STP terminal and that of the ST1- terminal of the hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more. |
Condition 1:
·
Pre-crash safety system Condition 2:
·
Stop light switch assembly ·
Hybrid vehicle control ECU ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
Check for DTCs of the pre-crash safety system.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
When DTC P0571 is stored by the dynamic radar cruise control system, DTC C1A4B may be stored by the pre-crash safety system. Therefore, if DTC P0571 is stored, inspect the pre-crash safety system first.
| Result | Proceed to |
|---|---|
| DTC C1A4B is output | A |
| DTC C1A4B is not output | B |
A
B
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A79 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A79-2 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A79-7 (B) - Body ground | Always | 11 to 14 V |
| A79-6 (B) - Body ground | Power switch on (IG) | 11 to 14 V |
| A79-6 (B) - Body ground | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A21 and A22 hybrid vehicle control ECU connector.
Disconnect the A79 stop light switch assembly connector.
Disconnect the A58 skid control ECU (brake booster with master cylinder assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A22-28 (ST1-) - A79-5 (L) | Always | Below 1 Ω |
| A21-15 (STP) - A79-3 (L) | Always | Below 1 Ω |
| A22-28 (ST1-) or A79-5 (L) - Body ground | Always | 10 kΩ or higher |
| A21-15 (STP) or A79-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG