Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2017.12–2019.03
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B277112C42
1.135,5.063 1.406,5.25 0.271,0.188 1.771,6.323 2.042,6.51 0.271,0.188 4.917,6.323 5.188,6.51 0.271,0.188 3.385,7.552 3.656,7.74 0.271,0.188 3.948,5.063 4.219,5.25 0.271,0.188 5.51,5.052 5.781,5.24 0.271,0.188 4.75,3.719 5.125,3.917 0.375,0.198 2.333,3.719 2.688,3.906 0.354,0.188 6.063,5.042 6.333,5.229 0.271,0.188 1.677,1.76 1.885,1.76 false 1.677,2.094 1.885,2.094 false 4.01,1.125 4.01,0.875 4.01,0.875 4.094,0.875 false 0.719,2.781 1.021,2.781 false 0.906,1.521 1.302,1.802 0.396,0.281 10 false 2D 0.896,2.135 1.479,2.521 0.583,0.385 10 false 2C 5.854,1.49 6.406,1.844 0.552,0.354 10 false 2B 5.854,2.188 6.344,2.51 0.49,0.323 10 false 2A 1.927,1.677 2.49,2 0.563,0.323 10 false L201 4.146,0.813 4.677,1.115 0.531,0.302 10 false MB 1.927,2.021 2.365,2.26 0.438,0.24 10 false L190 1.177,5.083 1.844,5.427 0.667,0.344 10 false 2D 1.813,6.344 2.313,6.635 0.5,0.292 10 false 2B 4.958,6.344 5.365,6.625 0.406,0.281 10 false 2A 3.427,7.583 3.875,7.833 0.448,0.25 10 false MB 3.99,5.083 4.531,5.396 0.542,0.313 10 false 2C 5.563,5.063 5.938,5.292 0.375,0.229 10 false 2E 4.792,3.74 5.208,3.979 0.417,0.24 10 false L201 2.365,3.74 2.917,4.042 0.552,0.302 10 false L190 0.333,2.698 0.771,2.938 0.438,0.24 10 false 2E*A 0.333,2.865 0.771,3.104 0.438,0.24 10 false 2F*B 5.823,5.052 6.198,5.281 0.375,0.229 10 false *A 6.125,5.052 6.5,5.281 0.375,0.229 10 false 2F 6.375,5.042 6.75,5.271 0.375,0.229 10 false *B
*A for LHD *B for RHD


a.

Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2B-6 - Body ground W-B - Body ground Ground Always Below 1 Ω
2C-18 - Body ground Y - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
2E-1 - Body ground*1 W - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
2F-1 - Body ground*2 W - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
L190-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Connect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2B-7 - Body ground G - Body ground Taillights and rear side marker lights drive output Light control switch not in tail position Below 1 V
Light control switch in tail position 11 to 14 V
2B-26 - Body ground Y - Body ground Rear fog light drive output Light control switch in tail position, fog light switch in rear position Below 1 V
Light control switch in tail position, fog light switch off 11 to 14 V
2C-8 - Body ground LG - Body ground Front fog lights drive output Light control switch in tail or head position, fog light switch in front position 11 to 14 V
Light control switch in tail or head position, fog light switch off Below 1 V
2C-10 - Body ground BR - Body ground Parking lights and front side marker lights drive output Light control switch not in tail position Below 1 V
Light control switch in tail position 11 to 14 V
2C-20 - Body ground R - Body ground Parking brake switch input Parking brake switch on Below 1 V
Parking brake switch off 11 to 14 V
2C-22 - Body ground Y - Body ground High beam headlights drive output Dimmer switch in high or high flash position Below 1 V
Dimmer switch in low position 11 to 14 V
2C-32 - Body ground G - Body ground No. 1 integration relay drive output Light control switch in head position Below 1 V
Light control switch not in head position 11 to 14 V
2D-18 - Body ground BR - Body ground Taillights, rear side marker lights and license plate lights drive output Light control switch not in tail position Below 1 V
Light control switch in tail position 11 to 14 V
L201-1 (RFOG) - Body ground W - Body ground Rear fog light switch input Rear fog light switch on Below 1 V
Rear fog light switch off 11 to 14 V
L201-5 (HU) - Body ground LG - Body ground Dimmer switch high position signal input Dimmer switch in high position Below 1 V
Dimmer switch not in high position 11 to 14 V
L201-8 (HF) - Body ground R - Body ground Dimmer switch high flash position signal input Dimmer switch in high flash position Below 1 V
Dimmer switch not in high flash position 11 to 14 V
L201-15 (DRLE) - Body ground Y - Body ground Daytime running light system drive output Daytime running light system operates Below 1 V
Daytime running light system not operates 11 to 14 V
L201-20 (CLTB) - L201-22 (CLTE)*3 R - B Automatic light control sensor power supply output Power switch off Below 1 V
Power switch on (IG) and light control switch in AUTO position 11 to 14 V
L201-21 (CLTS) - Body ground*3 W - Body ground Automatic light control sensor signal input Power switch off Below 1 V
Power switch on (IG) and automatic light control system operates Pulse generation
(See waveform 1)
L201-27 (FFOG) - Body ground SB - Body ground Front fog light switch input Front fog light switch on Below 1 V
Front fog light switch off 11 to 14 V
L201-28 (A) - Body ground*3 G - Body ground Light control switch AUTO position signal input Light control switch in AUTO position Below 1 V
Light control switch not in AUTO position 11 to 14 V
L201-29 (HEAD) - Body ground P - Body ground Light control switch head position input Light control switch in head position Below 1 V
Light control switch not in head position 11 to 14 V
L201-30 (TAIL) - Body ground Y - Body ground Light control switch tail position signal input Light control switch in tail or head position Below 1 V
Light control switch not in tail or head position 11 to 14 V
L190-17 (AHBI) - Body ground*4 R - Body ground Auto high beam switch signal input Integration control and panel assembly (auto high beam switch) on Below 1 V
Integration control and panel assembly (auto high beam switch) off 11 to 14 V
L190-21 (RLEW) - Body ground*5 L - Body ground Light control ECU RH signal input Power switch on (IG) and light control switch off 11 to 14 V
Power switch on (IG) and light control switch in head position Pulse generation
L190-24 (LLEW) - Body ground*5 B - Body ground Light control ECU LH signal input Power switch on (IG) and light control switch off 11 to 14 V
Power switch on (IG) and light control switch in head position Pulse generation

*1: for LHD

*2: for RHD

*3: w/ Automatic Light Control

*4: w/ Automatic High Beam System

*5: for LED Headlight


i.
B113714N16
2.948,1.063 3.292,1.219 0.344,0.156 10 GND 1.844,1.177 1.969,1.333 0.125,0.156 10 A

Waveform 1

Item Content
Tester Connection L201-21 (CLTS) - Body ground
Tool setting 5 V/DIV., 5 ms./DIV.
Condition Power switch on (IG) and automatic light control system operates

HINT:

If the ambient light becomes brighter, width (A) becomes narrower.





CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight)


U155007N01
3.49,0.229 3.76,0.427 0.271,0.198 10 false A48

a.

Disconnect the A48 headlight leveling ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A48-1 (IG) - Body ground LG - Body ground IG power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
A48-9 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Connect the A48 headlight leveling ECU assembly connector.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A48-3 (HDLP) - Body ground V - Body ground Low beam headlight signal input Low beam headlights on Below 1.5 V
Low beam headlights off Above 5 V
A48-5 (INIT) - Body ground B - Body ground Initialization signal input Terminals LVL and GND of DLC3 connected Below 1 V
Terminals LVL and GND of DLC3 not connected Approximately 5 V
A48-6 (WNG) - Body ground L - Body ground Warning light drive output Warning light on Below 1 V
Warning light off 11 to 14 V
A48-10 (RH+) - Body ground W - Body ground Leveling motor RH power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
A48-11 (LH+) - Body ground R - Body ground Leveling motor LH power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
A48-12 (SBR) - Body ground P - Body ground Rear height control sensor power supply Power switch off Below 1 V
Power switch on (IG) 4.75 to 5.25 V
A48-16 (SPDR) - Body ground V - Body ground Vehicle speed signal input Vehicle is driven at approximately 20 km/h (12 mph) Pulse generation
(See waveform 1)
A48-17 (RHT) - Body ground B - Body ground Leveling motor RH operation signal input With low beam headlights on, vehicle height not changed Below 1 V
With low beam headlights on, change vehicle height and keep for more than 3 seconds 1.0 to 14.4 V
A48-18 (LHT) - Body ground G - Body ground Leveling motor LH operation signal input With low beam headlights on, vehicle height not changed Below 1 V
With low beam headlights on, change vehicle height and keep for more than 3 seconds 1.0 to 14.4 V
A48-19 (SHRL) - Body ground SB - Body ground Rear height control sensor signal input Power switch off Below 1 V
Power switch on (IG) 0.5 to 4.5 V
A48-21 (SGR) - Body ground Y - Body ground Rear height control sensor ground Always Below 1 Ω
A48-23 (RH-) - Body ground BR - Body ground Leveling motor RH ground Always Below 1 Ω
A48-24 (LH-) - Body ground LG - Body ground Leveling motor LH ground Always Below 1 Ω

i.
E389357N01
2.802,1.198 3.26,1.396 0.458,0.198 10 false GND

Waveform 1

Item Content
Tester Connection A48-16 (SPDR) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle is driven at approximately 20 km/h (12 mph)





CHECK FORWARD RECOGNITION CAMERA (w/ Automatic High Beam System)


Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>TERMINALS OF ECU