Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.12–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U0129  Lost Communication with Brake System Control Module  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0129 No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
·

Brake booster with master cylinder assembly (skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)



HINT:

This diagnostic procedure is for when DTC U0129 is output only by the hybrid vehicle control ECU (GTS display: Hybrid Control).


WIRING DIAGRAM

C240392E12
3.792,0.969 3.531,0.969 3.531,0.969 3.375,1.281 false 2.521,1.271 2.354,0.969 2.354,0.969 2.188,0.969 false 0.708,2.229 1.104,2.375 0.396,0.146 10 false 120 Ω 6.219,2.823 6.615,2.969 0.396,0.146 10 false ECM 6.135,2.219 6.531,2.365 0.396,0.146 10 false 120 Ω 0.198,2.823 2.01,3.365 1.813,0.542 10 false Hybrid Vehicle Control ECU 3.667,3.271 4.125,3.417 0.458,0.146 10 false CA2H 3.198,4.063 5.375,4.656 2.177,0.594 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 1.25,3.865 2.156,4.052 0.906,0.188 10 false Trouble Area 3.458,3.552 3.844,3.698 0.385,0.146 10 false IG1 3.198,3.448 3.375,3.594 0.177,0.146 10 false 16 3.708,3.073 3.958,3.219 0.25,0.146 10 false 35 4.365,3.073 4.625,3.219 0.26,0.146 10 false 34 4.854,3.458 5.198,3.604 0.344,0.146 10 false 28 4.458,3.552 4.813,3.698 0.354,0.146 10 false GND 4.156,3.271 4.615,3.417 0.458,0.146 10 false CA2L 1.104,5 3.042,5.177 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.104,5.396 3.042,5.573 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.24,5 5.969,5.177 1.729,0.177 10 false : CAN Branch Line (CANH) 4.24,5.396 5.938,5.573 1.698,0.177 10 false : CAN Branch Line (CANL) 2.875,4.063 3.229,4.24 0.354,0.177 10 false A58 3.865,0.875 5.792,1.063 1.927,0.188 10 false CAN No. 1 Junction Connector 2.292,3.729 3.271,3.906 0.979,0.177 10 false ECU-IG NO. 2 0.24,0.885 2.167,1.094 1.927,0.208 10 false CAN No. 5 Junction Connector 0.125,0.083 1.271,0.563 1.146,0.479 12 false Sub Bus 15:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If the hybrid vehicle control ECU outputs DTC U0100 and DTC U0129, check the branch circuit of sub bus 15.


Result:
Result Proceed to
The hybrid vehicle control ECU outputs only DTC U0129.
(GTS display: Hybrid Control)
A
The hybrid vehicle control ECU outputs DTC U0100 and U0129.
(GTS display: Hybrid Control)
B




A

2.CHECK DTC (BRAKE SYSTEM)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK DTC (BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Result:
Result Proceed to
DTC C1241 is not output. A
DTC C1241 is output. B




A

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154755E04
1.115,2.667 1.656,2.115 false 1.99,2.656 1.76,2.115 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.594,0.885 1.896,1.042 0.302,0.156 10 false A58 0.771,2.688 1.135,2.865 0.365,0.177 10 false CA2L 1.896,2.677 2.281,2.854 0.385,0.177 10 false CA2H

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU))