Home › Brake › BRAKE (REAR) › REAR BRAKE › from 2019.03
RM2070E _54 Brake _061926 BRAKE (REAR) _0301703 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C232658E01
0.741,1.269 0.905,1.411 0.163,0.143 10 *a 1.688,1.408 0.93,1.354 0.93,1.354 1.661,1.354 false

Align the matchmarks and install the rear disc.

Text in Illustration
*a Matchmark

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the parking brake shoe adjusting hole plug.


Hide 47722A 3.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.
C244056

Install the rear disc brake cylinder mounting to the rear axle beam assembly with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 4.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C211756

Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.
C244055

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


Hide 47814 5.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C211757

Apply a light layer of lithium soap base glycol grease to the contact surface of each rear disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.

Install a new rear disc brake cylinder slide bushing to each rear disc brake cylinder slide pin.


c.
C211758

Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of each rear disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


d.
C244054

Install the 2 rear disc brake cylinder slide pins to the rear disc brake cylinder mounting.


e.

Push the rear disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pin to the boot.


Hide 04948 6.INSTALL REAR DISC BRAKE FITTING KIT

a.
C244057E01
0.957,1.036 1.120,1.182 0.163,0.146 10 *2 1.662,1.032 1.855,1.184 0.193,0.152 10 *1 1.643,4.333 1.806,4.480 0.163,0.146 10 *2 1.003,4.33 1.195,4.482 0.193,0.152 10 *1

Install the 2 rear No. 1 disc brake pad support plates and 2 rear No. 2 disc brake pad support plates to the rear disc brake cylinder mounting.

Text in Illustration
*1 Rear No. 1 Disc Brake Pad Support Plate
*2 Rear No. 2 Disc Brake Pad Support Plate

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 04946 7.INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT

a.
C414175C01
0.198,0.125 3.271,1.469 3.073,1.344 0.198,1.667 3.271,3.01 3.073,1.344 0.333,0.229 0.615,0.49 0.281,0.26 12 false *A 0.427,1.74 0.74,1.99 0.313,0.25 12 false *B
*A Inner Side
*B Outer Side


Check the rear disc brake pad.

NOTICE:
·

When using new rear disc brake pads, as the shape of the inner side rear disc brake pad and outer side rear disc brake pad is different, make sure to confirm the installation location of each rear disc brake pad by identifying its shape.

·

When reusing the rear disc brake pads, make sure to confirm the installation location of each rear disc brake pad by identifying the mark that was applied during removal.




b.
C236534

Apply disc brake grease to both sides of each rear No. 1 anti-squeal shim as shown in the illustration.

Text in Illustration
V100145

Disc Brake Grease


c.
C414901C02
0.51,1.083 0.51,1.396 false 0.927,1.302 0.927,1.604 false 2.573,2.219 2.573,2.521 false 3.031,2.49 3.031,2.792 false 1.521,2.188 1.521,2.865 false 2.146,2.563 2.146,2.656 2.146,2.656 1.521,2.656 false 0.865,1.615 1.063,1.813 0.198,0.198 10 false *1 0.427,1.406 0.656,1.646 0.229,0.24 10 false *2 1.448,2.875 1.677,3.083 0.229,0.208 10 false *3 2.5,2.542 2.75,2.781 0.25,0.24 10 false *1 2.948,2.823 3.198,3.073 0.25,0.25 10 false *2
*1 Rear No. 1 Anti-squeal Shim
*2 Rear No. 2 Anti-squeal Shim
*3 Pad wear indicator plate


Install the rear No. 1 anti-squeal shim and rear No. 2 anti-squeal shim to each rear disc brake pad.

NOTICE:
·

Install the shims in the correct positions and directions.

·

Disc brake grease can seep out slightly from the area where the anti-squeal shim is installed.

·

Make sure that disc brake grease is not applied onto the lining surface.




d.

Install the 2 pad wear indicator plates to the 2 rear disc brake pads.

NOTICE:

Install each pad wear indicator plate in the correct position and direction.



Hide 04466 8.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:
·

There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.

·

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.

·
C414175C01
0.198,0.125 3.271,1.469 3.073,1.344 0.198,1.667 3.271,3.01 3.073,1.344 0.333,0.229 0.615,0.49 0.281,0.26 12 false *A 0.427,1.74 0.74,1.99 0.313,0.25 12 false *B
*A Inner Side
*B Outer Side


When using new rear disc brake pads, as the shape of the inner side rear disc brake pad and outer side rear disc brake pad is different, make sure to confirm the installation location of each rear disc brake pad by identifying its shape.

·

When reusing the rear disc brake pads, make sure to confirm the installation location of each rear disc brake pad by identifying the mark that was applied during removal.




Hide 47850 9.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C414893C02
0.229,2.948 0.583,3.219 0.354,0.271 10 false *a 1.198,2.979 1.563,3.281 0.365,0.302 10 false *b
*a Hold
*b Turn


Hold the 2 rear disc brake cylinder slide pins and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47319F 10.CONNECT REAR FLEXIBLE HOSE

a.
C244060

Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)


Hide 11.FILL RESERVOIR WITH BRAKE FLUID

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>INSTALLATION).


b.

Perform the following procedure if air bleeding is not necessary:

i.

Connect the reservoir level switch connector.




Hide 14.ADJUST PARKING BRAKE

Hide 15.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)