Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2020.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1234  Yaw Rate Sensor  C1243  Deceleration Sensor Stuck  C1244  Open or Short Circuit in Deceleration Sensor Circuit  C1245  Abnormal Output in Deceleration Sensor  C1279  Abnormal Output Voltage in Deceleration Sensor (Test Mode DTC)  C1381  Abnormal Power Supply Voltage in Yaw Rate and/or Deceleration Sensor  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.

The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there are any problems in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTCs U0123 (Lost Communication With Yaw Rate Sensor Module) and U0124 (Lost Communication With Lateral Acceleration Sensor Module) are output.

These DTCs are also output when calibration has not been completed.

DTC C1279 will be cleared when the yaw rate and acceleration sensor (airbag ECU assembly) sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279 is output only in Test Mode.

DTC Code INF Code DTC Detection Condition Trouble Area
C1234 711 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 1 (GL1) malfunction). Yaw rate sensor (Airbag ECU assembly) internal malfunction
↑ 712 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 2 (GL2) malfunction). ↑
↑ 713 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Zero point calibration malfunction). ↑
↑ 714 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Two-value comparison malfunction). ↑
C1243 561 An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph). Acceleration sensor (Airbag ECU assembly) internal stuck malfunction
↑ 562
563
564
565
A stuck acceleration sensor value is determined. ↑
C1244 571 Either of the following is detected:
1.

Difference between GL1 and GL2 does not become less than 0.4 G for 60 seconds or more after reaching 0.6 G when the vehicle is stopped.

2.

A malfunction signal from the acceleration sensor is received.


·

Acceleration sensor (Airbag ECU assembly) installed improperly

·

Acceleration sensor (Airbag ECU assembly)


C1245 581 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (Airbag ECU assembly) installed improperly

·

Acceleration sensor (Airbag ECU assembly)


C1381 601 While acceleration sensor communication is enabled, a supply voltage malfunction signal is received from the sensor for 10 seconds.
·

Acceleration sensor (Airbag ECU assembly) supply voltage shut down

·

Acceleration sensor (Airbag ECU assembly)

·

Brake booster with master cylinder (Skid control ECU)


C1279 - Detected only during Test Mode.
·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)



WIRING DIAGRAM

C246787E27
0.073,3.927 0.552,4.177 0.479,0.25 10 false L16 4.896,4.198 7.094,4.677 2.198,0.479 10 false Brake Booster with Master Cylinder 6.052,1.302 6.479,1.448 0.427,0.146 10 false CA1H 6.052,0.677 6.479,0.823 0.427,0.146 10 false CA1L 4.906,4.031 5.333,4.25 0.427,0.219 10 false A58 5.802,1.198 6.031,1.354 0.229,0.156 10 false 37 5.802,0.594 6,0.75 0.198,0.156 10 false 38 3.917,1.927 4.917,2.083 1,0.156 10 false from IG2 Relay 2.344,2.083 2.708,2.323 0.365,0.24 10 false IGN 1.281,1.813 1.479,1.979 0.198,0.167 10 false 21 1.281,1.198 1.479,1.365 0.198,0.167 10 false 13 1.281,0.594 1.458,0.76 0.177,0.167 10 false 22 0.781,1.302 1.208,1.448 0.427,0.146 10 false CANH 0.938,1.906 1.24,2.052 0.302,0.146 10 false IG2 1.01,2.531 1.24,2.677 0.229,0.146 10 false E1 0.792,0.677 1.219,0.823 0.427,0.146 10 false CANL 0.063,4.094 2.219,4.656 2.156,0.563 10 false Yaw Rate and Acceleration Sensor (Airbag ECU Assembly) 1.01,3.156 1.24,3.302 0.229,0.146 10 false E2 1.281,2.427 1.479,2.594 0.198,0.167 10 false 25 1.281,3.063 1.479,3.229 0.198,0.167 10 false 26

CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).


HINT:

When U0123 and/or U0124 is output together with C1234, C1243, C1244, C1245, and/or C1381, inspect and repair the trouble areas indicated by U0123 and/or U0124 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073).


PROCEDURE

1.CHECK DTC

b.

Turn the power switch off (lock).


c.

Turn the power switch on (ready).


d.

Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).


f.

Check if DTC C1210 (Zero Point Calibration of Yaw Rate Sensor undone) or C1336 (Zero Point Calibration of Deceleration Sensor undone) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1210, C1336 and CAN communication system DTC) are not output A
CAN communication system DTC is output B
DTCs (C1210 and/or C1336) are output C




A

2.CHECK AIRBAG ECU ASSEMBLY

B

C

2.CHECK AIRBAG ECU ASSEMBLY
a.

Turn the power switch off (lock).


b.

Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).

OK:

The airbag ECU assembly is tightened to the specified torque.

The airbag ECU assembly is not tilted.




OK

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
U191088E01
1.031,2.125 0.573,2.792 false 0.406,0.75 0.802,0.927 0.396,0.177 10 false L16 0.24,0.219 0.458,0.396 0.219,0.177 10 false *a 0.385,2.823 0.677,3 0.292,0.177 10 false IG2

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the yaw rate and acceleration sensor (airbag ECU assembly) connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L16-21 (IG2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (E TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (E TERMINAL)
a.
U191089E01
0.437,0.746 0.838,0.922 0.401,0.177 10 L16 0.243,0.217 0.463,0.394 0.220,0.177 10 *a 1.655,2.154 1.195,2.818 false 1.039,2.864 1.328,3.041 0.290,0.177 10 E1 1.797,2.154 2.256,2.818 false 2.182,2.864 2.471,3.041 0.290,0.177 10 E2

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L16-25 (E1) - Body ground Always Below 1 Ω
L16-26 (E2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly))

NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (E CIRCUIT)