Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2020.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B282766E41
5.792,0.729 6.208,0.906 0.417,0.177 10 false CUTB 4.719,0.844 5.573,1.021 0.854,0.177 10 false ECU-B 2.729,0.698 4.271,0.969 1.542,0.271 10 false from Auxiliary Battery 4.698,1.333 5.458,1.615 0.76,0.281 10 false ECU-B2 5.396,0.719 5.74,0.979 0.344,0.26 10 false L195 5.479,0.531 5.656,0.708 0.177,0.177 10 false 10 5.802,4.396 6.24,4.573 0.438,0.177 10 false RDAM 5.458,4.219 5.635,4.396 0.177,0.177 10 false 17 5.802,4.896 6.219,5.073 0.417,0.177 10 false CSEL 5.51,4.708 5.688,4.885 0.177,0.177 10 false 6 5.813,5.396 6.229,5.573 0.417,0.177 10 false E 5.438,5.771 6.958,6.25 1.521,0.479 10 false Certification ECU (Smart Key ECU Assembly) 0.375,5.573 0.74,5.75 0.365,0.177 10 false S12 0.375,5.75 1.833,5.927 1.458,0.177 10 false Door Control Receiver 5.469,5.219 5.771,5.542 0.302,0.323 10 false 11 5.802,1.177 6.031,1.354 0.229,0.177 10 false +B 5.521,1 5.625,1.177 0.104,0.177 10 false 2 5.792,3.896 6.135,4.073 0.344,0.177 10 false RCO 1.469,3.896 1.875,4.198 0.406,0.302 10 false +5 1.771,3.802 1.948,3.979 0.177,0.177 10 false 4 1.281,4.396 1.677,4.573 0.396,0.177 10 false DATA 1.771,4.292 1.948,4.469 0.177,0.177 10 false 5 1.771,4.781 1.948,4.958 0.177,0.177 10 false 2 1.333,5.344 1.708,5.521 0.375,0.177 10 false GND 1.771,5.219 1.948,5.396 0.177,0.177 10 false 1 5.5,3.708 5.604,3.885 0.104,0.177 10 false 5 5.396,1.188 5.844,1.563 0.448,0.375 10 false L195 5.406,5.396 5.729,5.688 0.323,0.292 10 false L195 5.406,3.896 5.74,4.208 0.333,0.313 10 false L196 5.396,4.406 5.708,4.719 0.313,0.313 10 false L196 5.396,4.885 5.75,5.167 0.354,0.281 10 false L196 1.281,4.885 1.698,5.063 0.417,0.177 10 false CSEL 2.75,1.719 4.375,1.896 1.625,0.177 10 false to IG1 Relay Circuit 2.75,2.229 3.979,2.406 1.229,0.177 10 false to IG2 Relay Circuit 2.583,3.25 3.979,3.427 1.396,0.177 10 false from IGN Fuse Circuit 5.792,2.229 6.229,2.406 0.438,0.177 10 false IG2D 5.51,2.031 5.688,2.208 0.177,0.177 10 false 9 5.802,3.25 6.219,3.427 0.417,0.177 10 false IG 5.5,3.073 5.677,3.25 0.177,0.177 10 false 5 5.792,1.719 6.135,1.896 0.344,0.177 10 false IG1D 5.51,1.521 5.615,1.698 0.104,0.177 10 false 6 5.385,1.719 5.688,1.927 0.302,0.208 10 false L197 5.385,2.219 5.74,2.552 0.354,0.333 10 false L195 5.385,3.24 5.792,3.573 0.406,0.333 10 false L197 2.677,2.729 4.375,2.906 1.698,0.177 10 false to ACC Relay Circuit 5.802,2.698 6.219,2.875 0.417,0.177 10 false ACCD 5.5,2.531 5.677,2.708 0.177,0.177 10 false 4 5.385,2.698 5.719,3.021 0.333,0.323 10 false L197 0.125,0.208 6.177,0.448 6.052,0.24 12 false w/o Tire Pressure Warning System:

B441726E04
5.26,2.875 5.677,3.052 0.417,0.177 10 false CUTB 3.958,3.021 4.823,3.198 0.865,0.177 10 false ECU-B 4.927,2.698 5.104,2.875 0.177,0.177 10 false 10 5.26,5.177 5.698,5.354 0.438,0.177 10 false RDAM 4.917,4.979 5.094,5.156 0.177,0.177 10 false 17 5.25,5.74 5.667,5.917 0.417,0.177 10 false CSEL 4.969,5.542 5.146,5.719 0.177,0.177 10 false 6 5.26,6.281 5.677,6.458 0.417,0.177 10 false E 4.938,6.771 6.531,7.177 1.594,0.406 10 false Certification ECU (Smart Key ECU Assembly) 0.354,6.375 0.708,6.552 0.354,0.177 10 false R42 0.354,6.531 2.156,7.073 1.802,0.542 10 false Door Control and Tire Pressure Monitoring System 4.927,6.094 5.104,6.271 0.177,0.177 10 false 11 5.26,3.438 5.49,3.615 0.229,0.177 10 false +B 4.969,3.25 5.073,3.427 0.104,0.177 10 false 2 5.271,4.635 5.615,4.813 0.344,0.177 10 false RCO 1.698,4.625 1.875,4.802 0.177,0.177 10 false +5 1.979,4.521 2.156,4.698 0.177,0.177 10 false 10 1.51,5.177 1.906,5.354 0.396,0.177 10 false DATA 2.021,5.083 2.198,5.26 0.177,0.177 10 false 9 2.021,5.625 2.198,5.802 0.177,0.177 10 false 6 1.563,6.229 1.938,6.406 0.375,0.177 10 false GND 1.979,6.135 2.156,6.313 0.177,0.177 10 false 12 4.979,4.448 5.156,4.625 0.177,0.177 10 false 5 1.51,5.708 1.927,5.885 0.417,0.177 10 false CSEL 1.438,2.875 2.844,3.083 1.406,0.208 10 false from Auxiliary Battery 5.25,1.781 5.677,1.958 0.427,0.177 10 false ACCD 5.26,0.677 5.698,0.854 0.438,0.177 10 false IG1D 5.26,1.219 5.698,1.396 0.438,0.177 10 false IG2D 4.969,0.5 5.146,0.656 0.177,0.156 10 false 6 4.969,1.615 5.146,1.771 0.177,0.156 10 false 4 4.958,1.063 5.135,1.219 0.177,0.156 10 false 9 1.708,4.167 1.917,4.344 0.208,0.177 10 false IG 2.396,4.313 3.427,4.5 1.031,0.188 10 false ECU-IG NO. 1 2.021,4.073 2.198,4.25 0.177,0.177 10 false 1 4.854,4.635 5.188,4.813 0.333,0.177 10 false L196 2.094,2.333 3.896,2.49 1.802,0.156 10 false from IGN Fuse Circuit 5.281,2.333 5.698,2.51 0.417,0.177 10 false IG 4.979,2.146 5.156,2.323 0.177,0.177 10 false 5 2.292,0.688 3.688,0.844 1.396,0.156 10 false to IG1 Relay Circuit 2.271,1.229 3.667,1.385 1.396,0.156 10 false to IG2 Relay Circuit 2.188,1.802 3.823,1.958 1.635,0.156 10 false to ACC Relay Circuit 0.219,0.177 3.094,0.49 2.875,0.313 12 false w/ Tire Pressure Warning System: 3.927,3.583 4.792,3.76 0.865,0.177 10 false ECU-B2 4.865,1.802 5.313,1.979 0.448,0.177 10 false L197 4.865,2.344 5.313,2.521 0.448,0.177 10 false L197 4.854,0.698 5.302,0.875 0.448,0.177 10 false L197 4.854,1.25 5.302,1.427 0.448,0.177 10 false L195 4.865,2.906 5.313,3.083 0.448,0.177 10 false L195 4.865,3.448 5.313,3.625 0.448,0.177 10 false L195 4.854,6.281 5.302,6.458 0.448,0.177 10 false L195 4.865,5.188 5.198,5.365 0.333,0.177 10 false L196 4.865,5.74 5.198,5.917 0.333,0.177 10 false L196

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the door control and tire pressure monitoring system receiver assembly read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION).*

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the door control and tire pressure monitoring system receiver assembly if the door control receiver has been replaced.*

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) Precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".


*: w/ Tire Pressure Warning System



PROCEDURE

1.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery with the power switch off.

Standard Voltage:

11 to 14 V


HINT:

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the GTS and check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).

HINT:

When using the GTS with the vehicle power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


OK:

DTCs are not output.




OK

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

4.CHECK KEY DIAGNOSTIC MODE

NG

4.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter cannot be detected by channel 2 due to a malfunction, such as wave interference (w/ Tire Pressure Warning System).


i.
B441720E01
0.177,0.043 0.624,0.269 0.448,0.225 12 *A 0.177,2.106 0.624,2.331 0.448,0.225 12 *B 2.128,1.212 2.575,1.437 0.448,0.225 10 *a 1.775,3.481 2.223,3.706 0.448,0.225 10 *a

Check the electrical key antenna (for driver door):

Text in Illustration
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.


ii.
B441721E01
0.117,0 0.467,0.345 0.350,0.345 12 *A 0.117,2.09 0.467,2.434 0.350,0.345 12 *B 1.818,1.127 2.169,1.472 0.350,0.345 10 *a 2.136,3.508 2.486,3.852 0.350,0.345 10 *a

Check the electrical key antenna (for front passenger door):

Text in Illustration
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.


iii.
B441697E01
2.611,0.149 3.114,0.458 0.503,0.309 10 *a 2.277,0.231 1.838,1.189 false 2.566,0.229 2.276,0.229 2.276,0.229 0.652,1.2 false

Check the No. 1 indoor electrical key antenna (front floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


iv.
B441698E01
2.622,0.057 3.009,0.401 0.387,0.344 10 *a 2.298,0.17 1.863,0.938 false 2.589,0.16 2.299,0.16 2.299,0.16 0.624,0.95 false

Check the No. 3 indoor electrical key antenna (rear floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


v.
B441696E01
1.921,1.326 2.612,1.611 0.691,0.284 10 *a

Check the electrical key antenna (outside luggage):

Text in Illustration
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.


Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspections fail for only one of the channels C





A

5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

10.CHECK WAVE ENVIRONMENT

C

21.CHECK WAVE ENVIRONMENT
5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.

Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B




A

6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

7.CHECK ENTRY DOOR LOCK OPERATION
6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.




NEXT

7.CHECK ENTRY DOOR LOCK OPERATION
7.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

OK:

Entry lock/unlock operate normally.




OK

8.CHECK TRANSMITTER BATTERY

NG

10.CHECK WAVE ENVIRONMENT
8.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C


HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid system by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.






A

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

REPLACE TRANSMITTER BATTERY

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery.

i.
B281811E06
1.781,1.052 1.781,0.156 1.781,0.156 2.042,0.156 true 2.083,0.073 2.25,0.24 0.167,0.167 10 false *1

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>REMOVAL).


ii.

Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

Text in Illustration
*1 Lead Wire

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B281812E12
1.156,0.698 1.688,0.698 1.688,0.698 2.229,1.094 true 0.938,0.604 1.104,0.76 0.167,0.156 10 false *1

Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes" (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).



Text in Illustration
*1 GND

Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Power switch off, all doors closed and lock sensor touched 2.3 to 3.2 V





OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

10.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.


Result:
Result Proceed to
OK A
NG (w/ Tire Pressure Warning System) B
NG (w/o Tire Pressure Warning System) C




A

AFFECTED BY WAVE INTERFERENCE

B

11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

13.READ VALUE USING GTS
11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

U190836E02
4.385,1.615 4.094,2.313 true 1.979,1.74 1.708,2.292 true 4.542,1.615 4.833,2.313 true 0.302,0.292 0.49,0.448 0.188,0.156 10 false *a 4.792,0.938 5.156,1.094 0.365,0.156 10 false L197 2.156,0.927 2.542,1.083 0.385,0.156 10 false L195 3.927,2.313 4.292,2.469 0.365,0.156 10 false IG1D 1.531,2.313 1.896,2.469 0.365,0.156 10 false IG2D 4.646,2.323 5.073,2.479 0.427,0.156 10 false ACCD

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Power Source Control / Data List.


f.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON ALL OFF: Power switch off
ACC ON: Power switch on (ACC) (ACC relay on)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).


g.

Measure the voltage while checking the Data List on the GTS.

Standard Voltage:
Tester Connection Condition Specified Condition
L179-6 (IG1D) - Body ground Power switch off Below 1 V
Power switch on (ACC) Below 1 V
Power switch on (IG) 9 V or higher
L195-9 (IG2D) - Body ground Power switch off Below 1 V
Power switch on (ACC) Below 1 V
Power switch on (IG) 9 V or higher
L179-4 (ACCD) - Body ground Power switch off Below 1 V
Power switch on (IG) 9 V or higher
Power switch on (ACC) 9 V or higher


HINT:

Using the GTS, measure the voltage while confirming the power source mode on the Data List.




OK

12.READ VALUE USING GTS

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ignition Switch Power switch on (IG) / ON or OFF ON: Power switch on (IG)
OFF: Power switch off
·

Displays whether the IG power source signal input is on or off.

·

Use this Data List item to help determine the cause when all entry and start system/wireless functions do not operate.

·

If the electrical key transmitter sub-assembly is brought inside the vehicle and the power switch is pressed twice without depressing the brake pedal, the power switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the S code stored in the certification ECU (smart key ECU assembly) and the code stored in the ID code box (immobiliser code ECU) are compared, and if all codes match, the power source mode is considered on (IG) at that time.





OK

13.READ VALUE USING GTS

NG

CHECK RELAY CONTACT SIDE CIRCUIT

13.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Power switch status / ON or OFF ON: Power switch on (ACC)
OFF: Power switch off
-
IG SW Power switch status / ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-



OK

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)

NG

TROUBLESHOOT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)
a.
U190858E02
1.135,1.292 0.833,1.823 true 2.302,1.156 2.792,1.792 true 2.323,0.969 2.771,0.75 true 1.573,0.188 1.948,0.365 0.375,0.177 10 false L195 0.156,0.073 0.438,0.25 0.281,0.177 10 false *a 0.781,1.833 1.135,2.01 0.354,0.177 10 false E 2.792,0.646 3.146,0.823 0.354,0.177 10 false +B 2.552,1.792 2.99,1.969 0.438,0.177 10 false CUTB

Disconnect the L195 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L195-11 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L195-10 (CUTB) - Body ground Power switch off 11 to 14 V
L195-2 (+B) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -



OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
a.

w/o Tire Pressure Warning System:

i.

Disconnect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the S12 door control receiver connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L196-5 (RCO) - S12-4 (+5) Always Below 1 Ω
L196-17 (RDAM) - S12-5 (DATA) Always Below 1 Ω
L196-6 (CSEL) - S12-2 (CSEL) Always Below 1 Ω
L196-5 (RCO) or S12-4 (+5) - Body ground Always 10 kΩ or higher
L196-17 (RDAM) or S12-5 (DATA) - Body ground Always 10 kΩ or higher
L196-6 (CSEL) or S12-2 (CSEL) - Body ground Always 10 kΩ or higher




b.

w/ Tire Pressure Warning System:

i.

Disconnect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the R42 door control receiver connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L196-5 (RCO) - R42-10 (+5) Always Below 1 Ω
L196-17 (RDAM) - R42-9 (DATA) Always Below 1 Ω
L196-6 (CSEL) - R42-6 (CSEL) Always Below 1 Ω
L196-5 (RCO) or R42-10 (+5) - Body ground Always 10 kΩ or higher
L196-17 (RDAM) or R42-9 (DATA) - Body ground Always 10 kΩ or higher
L196-6 (CSEL) or R42-6 (CSEL) - Body ground Always 10 kΩ or higher





OK

16.CHECK DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK DOOR CONTROL RECEIVER
a.
U190860E02
2.052,1.24 2.344,1.865 true 1.385,3.604 1,4.063 true 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 1.073,0.271 1.281,0.469 0.208,0.198 10 false *a 1.094,2.375 1.302,2.573 0.208,0.198 10 false *a 0.667,0.906 1.073,1.104 0.406,0.198 10 false S12 2.188,1.885 2.604,2.083 0.417,0.198 10 false GND 0.719,3.031 1.073,3.229 0.354,0.198 10 false R42 0.823,4.073 1.24,4.271 0.417,0.198 10 false GND

Connect the S12*1 or R42*2 door control receiver connector.


b.

Connect the L196 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S12-1 (GND)*1 - Body ground Always Below 1 Ω
R42-12 (GND)*2 - Body ground


·

*1: w/o Tire Pressure Warning System

·

*2: w/ Tire Pressure Warning System


Text in Illustration
*A w/o Tire Pressure Warning System
*B w/ Tire Pressure Warning System
*a Component with harness connected
(Door Control Receiver)

Result:
Result Proceed to
OK A
NG (w/o Tire Pressure Warning System) B
NG (w/ Tire Pressure Warning System) C




A

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

w/o Tire Pressure Warning System:

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the S12 door control receiver connector.


iii.
U190859E02
2.063,1.094 2.354,1.792 true 1.906,1.115 1.906,1.813 true 1.521,1.115 1.229,1.802 true 0.24,0.115 0.448,0.313 0.208,0.198 10 false *a 0.625,0.656 0.917,0.854 0.292,0.198 10 false S12 2.25,1.823 2.667,2.021 0.417,0.198 10 false GND 1.792,1.823 2.208,2.021 0.417,0.198 10 false CSEL 1.115,1.833 1.323,2.021 0.208,0.188 10 false +5

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S12-4 (+5) - S12-1 (GND) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch not pressed


Below 1 V
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch pressed


4.5 to 5.5 V
S12-2 (CSEL) - S12-1 (GND) Power switch off and all doors closed Below 1 V → Pulse generation


Text in Illustration
*a Component with harness connected
(Door Control Receiver)



b.

w/ Tire Pressure Warning System:

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the R42 door control receiver connector.


iii.
U190948E02
1.365,1.292 1.219,1.698 true 1.354,1.052 0.917,1.406 true 2.531,1.313 2.083,1.031 true 2.406,1.667 2.083,1.25 true 0.177,0.125 0.385,0.323 0.208,0.198 10 false *a 0.521,0.542 0.865,0.74 0.344,0.198 10 false R42 1.052,1.719 1.469,1.917 0.417,0.198 10 false GND 0.521,1.354 0.938,1.552 0.417,0.198 10 false CSEL 2.563,1.333 2.781,1.49 0.219,0.156 10 false IG 2.323,1.698 2.542,1.854 0.219,0.156 10 false +B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R42-10 (+5) - R42-12 (GND) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch not pressed


Below 1 V
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch pressed


4.5 to 5.5 V
R42-6 (CSEL) - R42-12 (GND) Power switch off and all doors closed Below 1 V → Pulse generation
R42-1 (IG) - R42-12 (GND) Power switch on (IG) 10 to 16 V
R42-7 (+B) - R42-12 (GND) Always 10 to 16 V


Text in Illustration
*a Component with harness connected
(Door Control Receiver)




OK

18.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.CHECK DOOR CONTROL RECEIVER
a.

w/o Tire Pressure Warning System:

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the S12 door control receiver connector.


iii.

Measure the voltage according to the value(s) in the table below.

U190925E02
1.531,1.281 1.25,1.75 true 2.177,1.26 2.469,1.708 true 1.719,0.417 2.219,0.729 0.5,0.313 10 false S12 1.073,1.771 1.573,2.083 0.5,0.313 10 false DATA 2.396,1.719 2.896,2.031 0.5,0.313 10 false GND 3.677,1.208 4.177,1.521 0.5,0.313 10 false GND 4.375,1.938 4.875,2.25 0.5,0.313 10 false *c 5.406,1.958 5.906,2.271 0.5,0.313 10 false *d 0.406,0.167 0.906,0.479 0.5,0.313 10 false *a 3.813,0.198 4.313,0.51 0.5,0.313 10 false *b

Standard Voltage:
Tester Connection Condition Tool Setting Specified Condition
S12-5 (DATA) - S12-1 (GND) Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter subassembly brought outside detection area but kept inside wireless function operational area

4.

Lock or unlock button of electrical key transmitter subassembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)


Text in Illustration
*a Component with harness connected
(Door Control Receiver)
*b Waveform
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed



b.

w/ Tire Pressure Warning System:

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the R42 door control receiver connector.


iii.

Measure the voltage according to the value(s) in the table below.

U190972E02
1.635,1.365 1.49,1.844 true 2.052,1.365 2.313,1.854 true 1.865,0.417 2.365,0.729 0.5,0.313 10 false R42 1.292,1.875 1.792,2.188 0.5,0.313 10 false GND 2.219,1.885 2.719,2.198 0.5,0.313 10 false DATA 3.948,0.188 4.448,0.5 0.5,0.313 10 false *b 3.813,1.125 4.313,1.438 0.5,0.313 10 false GND 4.51,1.865 5.01,2.177 0.5,0.313 10 false *c 5.594,1.865 6.094,2.177 0.5,0.313 10 false *d 0.323,0.104 0.823,0.417 0.5,0.313 10 false *a

Standard Voltage:
Tester Connection Condition Tool Setting Specified Condition
R42-9 (DATA) - R42-12 (GND) Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter subassembly brought outside detection area but kept inside wireless function operational area

4.

Lock or unlock button of electrical key transmitter subassembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)


Text in Illustration
*a Component with harness connected
(Door Control Receiver)
*b Waveform
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed

Result:
Result Proceed to
OK A
NG (w/o Tire Pressure Warning System) B
NG (w/ Tire Pressure Warning System) C





A

19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

20.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
20.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Wireless door lock functions operate normally.




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

21.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.




OK

AFFECTED BY WAVE INTERFERENCE

NG

22.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
22.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.

Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B




A

23.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

24.CHECK KEY DIAGNOSTIC MODE
23.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.


HINT:

Refer to Service Bulletin.



NEXT

24.CHECK KEY DIAGNOSTIC MODE
24.CHECK KEY DIAGNOSTIC MODE
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Wireless door lock buzzer sounds.




OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY THAT WAS INSPECTED FIRST WAS DEFECTIVE)

NG

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY)
25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY)
a.

w/o Tire Pressure Warning System

i.

Disconnect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the S12 door control and tire pressure monitoring system receiver assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L196-6 (CSEL) - S12-2 (CSEL) Always Below 1 Ω
L196-6 (CSEL) or S12-2 (CSEL) - Body ground Always 10 kΩ or higher




b.

w/ Tire Pressure Warning System

i.

Disconnect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the R42 door control and tire pressure monitoring system receiver assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L196-6 (CSEL) - R42-6 (CSEL) Always Below 1 Ω
L196-6 (CSEL) or R42-6 (CSEL) - Body ground Always 10 kΩ or higher





OK

26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

w/o Tire Pressure Warning System

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the S12 door control receiver connector.


iii.
U190933E02
1.896,1.104 2.042,1.813 true 2.063,1.073 2.729,1.771 true 1.594,0.219 1.979,0.448 0.385,0.229 10 false S12 2.615,1.792 3,2.021 0.385,0.229 10 false GND 1.896,1.844 2.281,2.073 0.385,0.229 10 false CSEL

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S12-2 (CSEL) - S12-1 (GND) Power switch off and all doors closed Below 1 V → Pulse generation


Text in Illustration
*a Component with harness connected
(Door Control Receiver Assembly)



b.

w/ Tire Pressure Warning System

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the R42 door control and tire pressure monitoring system receiver assembly connector.


iii.
U190949E02
1.365,1.281 1.219,1.677 true 1.354,1 1.635,0.354 true 0.177,0.104 0.385,0.302 0.208,0.198 10 false *a 0.531,0.531 0.875,0.729 0.344,0.198 10 false R42 1.031,1.698 1.448,1.896 0.417,0.198 10 false GND 1.573,0.177 1.99,0.375 0.417,0.198 10 false CSEL

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R42-6 (CSEL) - R42-12 (GND) Power switch off and all doors closed Below 1 V → Pulse generation


Text in Illustration
*a Component with harness connected
(Door Control and Tire Pressure Monitoring System Receiver Assembly)




OK

27.CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

27.CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY
a.

w/o Tire Pressure Warning System

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the S12 door control receiver connector.


iii.
U190934E02
1.375,1.115 1.063,1.719 true 2.063,1.125 2.458,1.688 true 1.594,0.219 1.979,0.448 0.385,0.229 10 false S12 2.385,1.708 2.771,1.938 0.385,0.229 10 false GND 0.865,1.74 1.313,1.969 0.448,0.229 10 false DATA

Measure the voltage according to the value(s) in the table below.

HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


Standard Voltage:
Tester Connection Condition Specified Condition
S12-5 (DATA) - S12-1(GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed*


Below 1 V → 10 to 16 V → Below 1 V


Text in Illustration
*a Component with harness connected
(Door Control Receiver)

*: While the electrical key antennas are being inspected in key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).




b.

w/ Tire Pressure Warning System

i.

Connect the L196 certification ECU (smart key ECU assembly) connector.


ii.

Connect the R42 door control and tire pressure monitoring system receiver assembly connector.


iii.
U190950E02
1.365,1.281 0.885,1.833 true 1.802,1.281 2.323,1.823 true 0.177,0.104 0.385,0.302 0.208,0.198 10 false *a 0.531,0.542 0.854,0.74 0.323,0.198 10 false R42 0.708,1.844 1.125,2.042 0.417,0.198 10 false GND 2.177,1.833 2.594,2.031 0.417,0.198 10 false DATA

Measure the voltage according to the value(s) in the table below.

HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


Standard Voltage:
Tester Connection Condition Specified Condition
R42-9 (DATA) - R42-12 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed*


Below 1 V → 10 to 16 V → Below 1 V


Text in Illustration
*a Component with harness connected
(Door Control and Tire Pressure Monitoring System Receiver Assembly)

*: While the electrical key antennas are being inspected in key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).




Result:
Result Proceed to
OK A
NG (w/o Tire Pressure Warning System) B
NG (w/ Tire Pressure Warning System) C



A

28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

29.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
29.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Wireless door lock functions operate normally.




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)