Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2020.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

The certification ECU (smart key ECU assembly) receives brake signal information from 2 sources. It receives a signal from the stop light switch assembly via a direct line, and a signal from the skid control ECU via CAN communication. If the information from these 2 sources is inconsistent, this DTC will be stored.

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



DTC No. DTC Detection Condition Trouble Area
B2284 Stop light switch assembly operation information received by the certification ECU (smart key ECU assembly) from the stop light switch assembly via a direct line and stop light switch assembly information from the skid control ECU via CAN are inconsistent.
·

ECU-B2 fuse

·

STOP fuse

·

Stop light switch assembly

·

CAN communication system

·

Skid control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



This DTC is stored when a mismatch between the brake signal from the direct line and the brake signal sent via CAN communication is detected.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2284 The brake signal information from the direct line and the brake signal information from the ECU via CAN communication are inconsistent (1-trip detection logic*).
·

ECU-B2 fuse

·

STOP fuse

·

Stop light switch assembly

·

CAN communication system

·

Skid control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Connect the cable to the negative (-) auxiliary battery terminal, turn the brakes off for 20 seconds or more and then turn them on for 20 seconds or more.

*: Only output while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
When the key is inside the vehicle, the hybrid control system does not start even though a hybrid control system start operation is performed (the power switch indicator does not illuminate in green). However, if the power switch is pressed and held for a certain period of time after the power source mode is changed to on (ACC), the hybrid control system can be started.
·

When a direct line ON malfunction is present, the hybrid control system can be started by pressing the power switch even if the brakes are off.

·

When a direct line OFF malfunction is present, the hybrid control system cannot be started by pressing the power switch even if the brakes are on.


-

WIRING DIAGRAM

B361495E19
0.188,0.396 1.146,0.771 0.958,0.375 10 false from Auxiliary Battery 2.271,0.573 2.979,0.729 0.708,0.156 10 false ECU-B2 1.698,1.406 2.271,1.656 0.573,0.25 10 false STOP 2.448,2.01 3.438,2.25 0.99,0.24 10 false A93 2.438,2.177 3.552,2.667 1.115,0.49 10 false Stop Light Switch Assembly 3.958,1.146 4.271,1.344 0.313,0.198 10 false 18 2.417,1.135 3.052,1.344 0.635,0.208 10 false 7 4.052,0.323 4.365,0.521 0.313,0.198 10 false 2 3.979,2.156 4.292,2.354 0.313,0.198 10 false 11 4.24,0.438 4.552,0.635 0.313,0.198 10 false +B 4.25,1.25 4.74,1.5 0.49,0.25 10 false STP1 4.25,2.302 4.74,2.552 0.49,0.25 10 false E 5.521,2.01 7.052,2.594 1.531,0.583 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.823,2.719 4.313,2.969 0.49,0.25 10 false L195 3.823,2.885 5.354,3.354 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 0.906,3.292 2.792,3.667 1.885,0.375 10 false : CAN Communication Line 3.49,1.604 3.802,1.802 0.313,0.198 10 false 2 2.656,1.229 3.146,1.479 0.49,0.25 10 false B 3.031,1.688 3.521,1.938 0.49,0.25 10 false GND 3.469,1.156 3.74,1.406 0.271,0.25 10 false 1 3.042,1.25 3.531,1.5 0.49,0.25 10 false OUT 0.177,1.229 1.135,1.604 0.958,0.375 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

HINT:

Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.


NOTICE:
·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2284
Power Source Control

Stop Light Switch1


ABS/VSC/TRAC

Stop Light SW


-


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the Techstream to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the Techstream.


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 Stop light switch1 ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning , the hybrid control system can be started by pressing and holding the power switch for a certain period of time.




OK

GO TO HYBRID CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - POWER SOURCE AND GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - POWER SOURCE AND GROUND)
a.
U190931E03
1.323,1.302 0.917,1.823 true 2.51,1.292 2.906,1.813 true 0.208,0.104 0.5,0.302 0.292,0.198 10 false *a 1.667,0.26 1.958,0.458 0.292,0.198 10 false A93 2.865,1.844 3.156,2.042 0.292,0.198 10 false B 0.75,1.844 1.167,2.042 0.417,0.198 10 false GND

Disconnect the A93 stop light switch assembly connector.

*a Front view of wire harness connector
(to Stop Light Switch Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A93-7 (B) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A93-2 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A93 stop light switch assembly connector.


b.
U190844E02
1.344,2.302 0.969,2.813 true 0.125,0.094 0.458,0.333 0.333,0.24 10 false *a 0.417,2.135 0.75,2.375 0.333,0.24 10 false L195 0.792,2.844 1.219,3.083 0.427,0.24 10 false STP1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L195-18 (STP1) - A93-1 (OUT) Always Below 1 Ω
L195-18 (STP1) or A93-1 (OUT) - Body ground Always 10 kΩ or higher



c.

Reconnect the A93 stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L195-18 (STP1) - Body ground Brake pedal released 1 V or less
Brake pedal depressed 9 V or higher



Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY