Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

for Preparation Click here


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.
The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140E55


DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
  1. Open or short in camshaft timing oil control valve assembly circuit
  2. Camshaft timing oil control valve assembly
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the ignition switch is ON (IG) or the engine is running, the ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0010: Camshaft timing oil control valve assembly range check
Required Sensors/Components (Main)
Camshaft timing oil control valve assembly
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None
All of the following conditions are met
-
Starter
Off
Ignition switch
ON (IG)
Time after ignition switch off to ON (IG)
0.5 seconds or more

Case 1 
Either of the following conditions is met
Conditions A or B
A. Both of the following conditions are met
-
Auxiliary battery voltage
11 V or higher, and less than 13 V
Target duty cycle
Less than 70%
B. Both of the following conditions are met
-
Auxiliary battery voltage
13 V or higher
Target duty cycle
Less than 80%

Case 2 
Current cut status
Not cut

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
Output duty cycle
100% or higher

Case 2 
Output duty cycle
3% or less

COMPONENT OPERATING RANGE


Output duty cycle
Higher than 3%, and less than 100%

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Wait 5 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0010.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A255118E18


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC (DTC P0010)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Clear the DTC after recording the freeze frame data and DTC.

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and allow the engine to idle.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0010 is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
  1. Disconnect the camshaft timing oil control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C20-1 - C10-75 (OC1+)
    Always
    Below 1 Ω
    C20-2 - C10-74 (OC1-)
    Always
    Below 1 Ω
    C20-1 or C10-75 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C20-2 or C10-74 (OC1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)