Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

for Preparation Click here


DESCRIPTION

The crank position sensor system consists of a crank angle sensor plate and a pickup coil.
The crank angle sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The crank angle sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
Either of the following conditions is met (1 trip detection logic):
  1. No crank position sensor signal to ECM while engine running.
  2. Missing crank position sensor signal despite cam position sensor signal inputs normal after engine cranked.
  1. Open or short in crank position sensor circuit
  2. Crank position sensor
  3. Crankshaft (crank angle sensor plate)
  4. ECM

  1. A063955E53
    Reference: Inspection using an oscilloscope.

    HINT:
    1. The correct waveform is as shown.
    2. G2+ stands for the cam position sensor signal, and NE+ stands for the crank position sensor signal.
    3. Grounding failure of the shielded wire may cause noise in the waveforms.

    ECM Terminal Name
    CH1: Between G2+ and G2-
    CH2: Between NE+ and NE-
    Tester Range
    5 V/DIV., 20 ms./DIV.
    Condition
    Idling

MONITOR DESCRIPTION

If there is no signal from the crank position sensor despite the crankshaft rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0335: Crank position sensor range check/rationality
P0335: Crank position sensor verify pulse input
Required Sensors/Components (Main)
Crank position sensor
Required Sensors/Components (Related)
Cam position sensor
Frequency of Operation
Continuous
Duration
-: Verify pulse input (case 1)
1.85 seconds: Verify pulse input (case 2)
0.016 seconds: Range check/rationality
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None
Lost communication with power management control ECU (U0293)
Not detected
Hybrid control module judge
Engine running

P0335: Crank Position Sensor Range Check/Rationality 
All of the following conditions are met
-
Engine speed signal
Signal input
Ignition switch
ON (IG)
Time after starter off to on
2.5 seconds or more
Number of cam position sensor signal pulses
6 times
Auxiliary battery voltage
7 V or higher
Cam position sensor circuit fail
Not detected

P0335: Crank Position Sensor Verify Pulse Input (Case 1) 
All of the following conditions are met
-
Starter
Off
Engine speed
600 rpm or higher
Time after starter from on to off
3 seconds or more

P0335: Crank Position Sensor Verify Pulse Input (Case 2) 
Both of the following conditions are met
-
Ignition switch
ON (IG)
Time after ignition switch off to ON (IG)
More than 0.5 seconds

TYPICAL MALFUNCTION THRESHOLDS


P0335: Crank Position Sensor Range Check/Rationality 
Number of crank position sensor signal pulses
87 times or less, or 219 times or more

P0335: Crank Position Sensor Verify Pulse Input 
Engine speed signal
No signal

COMPONENT OPERATING RANGE


Crank position sensor
  1. Crank position sensor output voltage fluctuates while crankshaft revolving
  2. 34 crank position sensor signals per crankshaft revolution

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine.
  8. Idle the engine for 20 seconds or more [A].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0335.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A268232E05


INSPECTION PROCEDURE

HINT:
  1. After performing the inspection procedure for the crank position sensor, if DTC P0335 is output again, check the following items related to the cam position sensor.
    1. Installation condition of the cam position sensor
    2. Installation condition of the camshaft
    3. Connection of the cam position sensor connector
  2. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  3. The engine speed can be checked by using the Techstream. To perform the check, follow the procedures below:
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON (IG).
    3. Turn the Techstream on.
    4. Put the engine in inspection mode (maintenance mode) (Click here).
    5. Start the engine.
    6. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crank position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crank position sensor output voltage is insufficient.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

  1. Read the values displayed on the Techstream while the engine is running.

    Standard:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the Techstream.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the Techstream remains at zero (0), there may be an open or short in the crank position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CRANK POSITION SENSOR (RESISTANCE)
  1. Inspect the crank position sensor (Click here).



NG
REPLACE CRANK POSITION SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)
  1. Disconnect the crank position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C29-1 - C10-78 (NE+)
    Always
    Below 1 Ω
    C29-2 - C10-110 (NE-)
    Always
    Below 1 Ω
    C29-1 or C10-78 (NE+) - Body ground
    Always
    10 kΩ or higher
    C29-2 or C10-110 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANK POSITION SENSOR)
BR03795E25
  1. Check the crank position sensor installation.

    OK:
    Crank position sensor is installed correctly.



NG
SECURELY REINSTALL CRANK POSITION SENSOR (Click here)
OK


5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)
  1. Inspect the teeth of the crank angle sensor plate.

    OK:
    Crank angle sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT (Click here)
OK

REPLACE ECM (Click here)