DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |
DTC P013A Oxygen Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 | Either of the following conditions is met:
|
|
| P0137 | Either of the following conditions is met:
|
|
| P0138 |
|
|
| P0139 | Heated oxygen sensor (sensor 2) voltage does not drop to less than 0.2 V immediately after fuel cut starts (2 trip detection logic) |
|
| P013A | Heated oxygen sensor (sensor 2) voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut status (1 trip detection logic) |
|
| Active Air fuel Ratio Control |
| Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136) |

| Open in Heated Oxygen Sensor Circuit (DTC P0137) |

| High or Low Impedance of Heated Oxygen Sensor (DTC P0136 or P0137) |
![]() |
| Extremely High Output Voltage of Heated Oxygen Sensor (DTC P0138) |
| Abnormal Voltage Output of Heated Oxygen Sensor during Fuel Cut (DTC P0139) |
| Abnormal Voltage Output of Heated Oxygen Sensor during Fuel Cut from Rich Condition (DTC P013A) |
| Related DTCs | P0136: Heated oxygen sensor voltage check (voltage malfunction) P0136: Heated oxygen sensor circuit continuity check (circuit short) P0137: Heated oxygen sensor voltage check (low voltage) P0137: Heated oxygen sensor circuit continuity check (circuit open) P0138: Heated oxygen sensor circuit continuity check (out of range) P0139: Heated oxygen sensor response rate during fuel cut P013A: Heated oxygen sensor response rate during fuel cut from rich condition |
| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Mass air flow meter sub-assembly Throttle position sensor Air fuel ratio sensor (sensor 1) |
| Frequency of Operation | Once per driving cycle: Active air fuel ratio control detection, Heated oxygen sensor abnormal voltage during fuel cut Continuous: Other |
| Duration | 20 seconds: Heated oxygen sensor voltage check (voltage malfunction, low voltage) 30 seconds: Heated oxygen sensor circuit continuity check (circuit short) 90 seconds: Heated oxygen sensor circuit continuity check (circuit open) 10 seconds: Heated oxygen sensor circuit continuity check (out of range) 7 seconds: Heated oxygen sensor response rate during fuel cut from rich condition 6 seconds: Heated oxygen sensor response rate during fuel cut |
| MIL Operation | 2 driving cycles: P0136, P0137, P0138 and P0139 Immediate: P013A |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | P0016 (VVT system bank 1 - Misalignment) P0031, P0032, P101D (Air fuel ratio sensor heater - Sensor 1) P0037, P0038, P102D (Heated oxygen sensor heater - Sensor 2) P0102, P0103 (Mass air flow meter) P0107, P0108 (Manifold absolute pressure) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P014C, P014D (Air fuel ratio sensor - Slow response) P015A, P015B (Air fuel ratio sensor - Delayed response) P0171, P0172 (Fuel system) P0301, P0302, P0303, P0304 (Misfire) P0335 (Crankshaft position sensor) P0401(EGR system (Closed)) P0451, P0452, P0453 (EVAP system) P2195, P2196 (Air fuel ratio sensor - Rationality) P219A, P219C, P219D, P219E, P219F (Air fuel ratio sensor - Imbalance) P2237 (Air fuel ratio sensor - Open) P2238, P2252 (Air fuel ratio sensor - Low impedance) P2239, P2253 (Air fuel ratio sensor - High impedance) |
| Monitor runs whenever following DTCs are not present | None |
| Auxiliary battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idle | OFF |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or more, and less than 70% |
| Auxiliary battery voltage | 11 V or higher |
| Estimated heated oxygen sensor temperature | Below 700°C (1292°F) |
| ECM monitor | Completed |
| DTC P0607 | Not set |
| Auxiliary battery voltage | 11 V or higher |
| Estimated heated oxygen sensor temperature | 450°C (842°F) or higher, and below 750°C (1382°F) |
| DTC P0607 | Not set |
| Auxiliary battery voltage | 11 V or higher |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 75°C (167°F) or higher |
| Catalyst temperature | 400°C (752°F) or higher |
| Fuel cut | On |
| Auxiliary battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Estimated catalyst temperature | 400°C (752°F) or higher |
| Fuel cut | On |
| All of the following conditions (a), (b) and (c) are met | - |
| (a) Commanded air fuel ratio | 14.4 or less |
| (b) Heated oxygen sensor voltage | 0.21 V or higher, and below 0.69 V |
| (c) Oxygen storage capacity of catalyst | 2.1 g or more |
| All of the following conditions (a), (b) and (c) are met | - |
| (a) Commanded air fuel ratio | 14.4 or less |
| (b) Heated oxygen sensor voltage | Below 0.21 V |
| (c) Oxygen storage capacity of catalyst | 2.1 g or more |
| Duration of following condition | 30 seconds or more |
| Heated oxygen sensor impedance | Below 5 Ω |
| Duration of following condition | 90 seconds or more |
| Heated oxygen sensor impedance | 15 kΩ or higher |
| Duration of following condition | 10 seconds or more |
| Heated oxygen sensor output voltage | 1.2 V or higher |
| Duration until heated oxygen sensor voltage drops to 0.2 V during fuel cut | 6 seconds or more |
| Duration that heated oxygen sensor voltage drops from 0.35 to 0.2 V during fuel cut (Normalized) | 1 or more |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $08 | Multiply by 0.001 | V | Maximum sensor voltage |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8D | Multiply by 0.001 | Seconds | Duration that sensor voltage drops to 0.2 V during fuel-cut |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8F | Multiply by 0.0003 | g | Maximum oxygen storage capacity |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $90 | Multiply by 0.001 | No dimension | Response rate during fuel cut from rich condition (Normalization) |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0139 OR P013A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0138 is output | A |
| DTC P0137 is output | B |
| DTC P0136 is output | C |
| DTC P0139 or P013A is output | D |
| DTC P0136, P0137, P0138, P0139 or P013A and other DTCs are output | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| *a | Component without harness connected (Heated Oxygen Sensor) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the ignition switch to off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C10-22 (HT1B) - C10-103 (OX1B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / O2S B1S2.
Change the fuel injection volume using the Techstream, and monitor the voltage output of heated oxygen sensor displayed on the Techstream.
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.
Change the fuel injection volume using the Techstream, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the Techstream.
| Techstream Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 (Air fuel ratio) | Alternates between higher and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |

|
| ||||
| OK | |
| 6.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stalls |
| MAP (Data List) | MAP value is 20 to 40 kPa(abs) [150 to 300 mmHg(abs)] (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 7.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C16-1 (HT1B) - C10-22 (HT1B) | Always | Below 1 Ω |
| C16-3 (OX1B) - C10-103 (OX1B) | Always | Below 1 Ω |
| C16-4 (E2) - C10-135 (EX1B) | Always | Below 1 Ω |
| C16-1 (HT1B) or C10-22 (HT1B) - Body ground | Always | 10 kΩ or higher |
| C16-3 (OX1B) or C10-103 (OX1B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 12.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0136, P0137 and P0138).
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0137) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0136 or P0137.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0136 or P0137 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 14.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stalls |
| MAP (Data List) | MAP value is 20 to 40 kPa(abs) [150 to 300 mmHg(abs)] (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 15.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||
| 16.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 17.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0136, P0137 and P0138).
| NEXT | |
| 18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0136.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0136 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 19.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stalls |
| MAP (Data List) | MAP value is 20 to 40 kPa(abs) [150 to 300 mmHg(abs)] (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 20.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||
| 21.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 22.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
Turn the ignition switch off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C10-22 (HT1B) - C10-103 (OX1B) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 23.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0139 and P013A).
| NEXT | |
| 24.READ OUTPUT DTC (DTC P0139 OR P013A IS OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0139 or P013A.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0139 or P013A is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 25.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stalls |
| MAP (Data List) | MAP value is 20 to 40 kPa(abs) [150 to 300 mmHg(abs)] (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 26.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||