DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
DTC P101D A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 | Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater output duty cycle is 30% or higher (1 trip detection logic). |
|
| P0032 | Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic). |
|
| P101D | The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). | ECM |
| Related DTCs | P0031: Air fuel ratio sensor heater range check (low current) P0032: Air fuel ratio sensor heater range check (high current) P101D: Air fuel ratio sensor heater performance |
| Required Sensors/Components (Main) | Air fuel ratio sensor heater |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second: P101D 10 seconds: P0031 10.24 seconds: P0032 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Auxiliary battery voltage | 10.5 V or higher |
| Time after heater on | 5 seconds or more |
| Active heater off control | Not operating |
| Active heater on control | Not operating |
| Air fuel ratio sensor heater performance fail (P101D) | Not detected |
| Output duty cycle | 30% or higher |
| All of the following conditions are met | - |
| Auxiliary battery voltage | 10.5 V or higher |
| Time after heater on | 5 seconds or more |
| Heater output duty cycle | Higher than 0% |
| Active heater off control | Not operating |
| Active heater on control | Not operating |
| All of the following conditions are met | - |
| Auxiliary battery voltage | 10.5 V or more |
| Output duty cycle | Less than 60% |
| Heater OFF current | Higher than 11 A |
| Command to heater output | OFF |
| Heater current detected by heater monitor IC | 11 A or higher |
| Air fuel ratio sensor heater low current fail (P0031) | Not detected |
| Active heater OFF control | Not operating |
| Active heater ON control | Not operating |
| Heater ON current | Less than 0.8 A |
| Both of the following conditions are met | - |
| Command to heater output | ON |
| Heater current detected by heater monitor IC | 11 A or higher |
| Both of the following conditions are met | - |
| Heater current detected by heater monitor IC | 11 A or higher |
| Heater OFF current | Higher than 11 A |
| Heater ON current | 0.8 A or higher |
| Both of the following conditions are met | - |
| Command to heater output | ON |
| Heater current detected by heater monitor IC | Less than 11 A |
| Heater OFF current | 11 A or less |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C17-2 (+B) - Body ground | Ignition switch ON (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C17-1 (HA1A) - C10-23 (HA1A) | Always | Below 1 Ω |
| C17-1 (HA1A) or C10-23 (HA1A) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0031, P0032 or P101D is output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY) |
Disconnect the air fuel ratio sensor connector.
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C17-2 (+B) - 2C-4 | Always | Below 1 Ω |
| C17-2 (+B) or 2C-4 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||