Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1252/52    Brake Booster Pump Motor on Time Abnormally Long

DTC    C1253/53    Pump Motor Relay Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1252/52
311
The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or more.)
  1. Short in motor circuit or motor monitor circuit
  2. Motor relay stuck
  3. Accumulator pressure sensor malfunction in brake actuator (Brake booster with master cylinder assembly)
  4. Skid control ECU (Brake booster with master cylinder assembly)
C1253/53
321
With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more after a motor drive on request.
  1. Open in motor circuit or motor monitor circuit
  2. Skid control ECU (Brake booster with master cylinder assembly)
↑
322
The motor drive monitor remains on for 2 seconds or more after a motor drive off request.
  1. Short in motor circuit or motor monitor circuit
  2. Skid control ECU (Brake booster with master cylinder assembly)
↑
323
The skid control ECU internal motor drive logical inconsistency continues for 2 seconds or more.
Skid control ECU (Brake booster with master cylinder assembly)
↑
324
An open circuit in both skid control ECU internal motor relays 1 and 2.
  1. Open in motor circuit or motor monitor circuit
  2. Skid control ECU (Brake booster with master cylinder assembly)
↑
325
An open circuit in both skid control ECU internal motor relays 1 and 3.
↑
↑
326
An open circuit in both skid control ECU internal motor relays 2 and 3.
↑
↑
327
An open circuit in skid control ECU internal motor relay 1.
↑
↑
328
An open circuit in skid control ECU internal motor relay 2.
↑
↑
329
An open circuit in skid control ECU internal motor relay 3.
↑

WIRING DIAGRAM


C256388E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

1.PERFORM ACTIVE TEST USING TECHSTREAM (ABS MOTOR RELAY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Select the Active Test on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Motor Relay
    ABS motor relay
    Relay ON/OFF
    -
    *: Electronically Controlled Brake System

  1. Select the Data List on the Techstream (Click here).


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ECB* Motor Relay
ABS motor relay / ON or OFF
ON: Relay on
OFF: Relay off
-
*: Electronically Controlled Brake System
  1. Check the operating condition of the ABS motor relay when operating it using the Techstream.

    Result:

    Result
    Proceed to
    ABS motor relay in the Data List turns ON/OFF using the Active Test.
    A
    ABS motor relay in the Data List does not change using the Active Test.
    B



B
Go to step 6
A


2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY


    C243137E04
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the brake booster pump assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A45-1 (BM1) - A45-2 (GND1)
    Always
    Below 10 Ω
    A46-2 (BM2) - A46-1 (GND2)
    Always
    Below 10 Ω
    A45-1 (BM1) - A46-2 (BM2)
    Always
    Below 1 Ω
    A45-2 (GND1) - A46-1 (GND2)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Booster Pump Assembly)



NG
REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    C243138E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A45-2 (GND1) - Body ground
    Always
    Below 1 Ω
    A46-1 (GND2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Booster Pump Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4.READ VALUE USING TECHSTREAM (ACCUMULATOR PRESSURE SENSOR)
  1. Reconnect the brake booster pump assembly connectors.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Select the Data List on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor /
    Min.: 0.00 V, Max.: 5.00 V
    Specified value: 2.90 to 4.20 V
    When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator

  1. Wait for 30 seconds without depressing the brake pedal.

  1. Check that the accumulator pressure sensor output value change is within the specified range.

    OK:
    Accumulator pressure sensor output value change is less than 0.55 V.



NG
Go to step 8
OK


5.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON (IG).

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTCs C1252/52 and C1253/53 are not output.
    A
    DTCs C1252/52 and/or C1253/53 are output.
    B



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)


    C249762E15
  1. Turn the ignition switch off.

  1. Check that the ABS MTR NO. 1 (30 A) and ABS MTR NO. 2 (30 A) fuses are normal.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A41-1 (MRI1) - Body ground
    Always
    11 to 14 V
    A41-2 (MRI2) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT)
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE BOOSTER PUMP ASSEMBLY)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the brake booster pump assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-29 (MRO1) - A45-1 (BM1)
    Always
    Below 1 Ω
    A41-29 (MRO1) - Body ground
    Always
    10 kΩ or higher
    A41-30 (MRO2) - A46-2 (BM2)
    Always
    Below 1 Ω
    A41-30 (MRO2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)  

8.PERFORM ACTIVE TEST USING TECHSTREAM (SOLENOID VALVE)
  1. Select the Active Test on the Techstream (Click here).

    HINT:
    The Active Test can be performed when the following conditions are met.
    1. ABS main relay is on.
    2. Shift lever is in P.
    3. Parking brake is applied.
    4. Vehicle speed is 0 km/h (0 mph).


    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Solenoid (SMC/SRC/SCC)
    Switching solenoid valve (SMC/SRC/SCC)
    Solenoid ON/OFF
    Operation sound of solenoid (clicking sound) can be heard
    *: Electronically Controlled Brake System

  1. Perform the Active Test of the solenoid using the Techstream.

  1. Select the Data List on the Techstream (Click here).


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Wheel Cylinder Pressure Sensor
Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 0.10 to 0.90 V
Reading increases when brake pedal is depressed
  1. Check that the output value of the wheel cylinder pressure sensor does not increase.

    OK:
    The output value of the wheel cylinder pressure sensor does not increase.

    HINT:
    If the output value increases, there may be brake fluid leaks in the brake actuator.



NG
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
OK

REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)