DTC B1498/98 Communication Malfunction (A/C Inverter Local) |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1498/98 |
|
|

| 1.CHECK CAN COMMUNICATION SYSTEM |
Use the Techstream to check if the CAN communication system is functioning normally.
| Result | Proceed to |
| CAN DTC is not output | A |
| CAN DTC is output | B |
|
| ||||
| A | |
| 2.CHECK DIAGNOSTIC TROUBLE CODE |
Check if DTCs for the hybrid control system are output using the Techstream.
| Result | Proceed to |
| DTC is not output | A |
| Only DTC P3108 is output | A |
| DTCs other than P3108 are output | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND) |
Disconnect the C22 compressor with motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C22-5 (GND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG CIRCUIT, GROUND) |
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C22-6 (IG1) - C22-5 (GND) | Ignition switch ON (IG) | 11 to 14 V |
| C22-6 (IG1) - C22-5 (GND) | Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY) |
Disconnect the A38 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C22-1 (CLK) - A38-19 (CLK) | Always | Below 1 Ω |
| C22-2 (DIN) - A38-31 (ITE) | Always | Below 1 Ω |
| C22-3 (DOUT) - A38-30 (ETI) | Always | Below 1 Ω |
| C22-1 (CLK) - Body ground | Always | 10 kΩ or higher |
| C22-2 (DIN) - Body ground | Always | 10 kΩ or higher |
| C22-3 (DOUT) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT ELECTRIC VEHICLE FUSE |
Turn the ignition switch off.
Remove the service plug grip (Click here).
Remove the connector cover assembly (Click here).
![]() |
Check that bolts A and B are tightened securely.
Measure the resistance according to the value(s) in the table below.
| Tester Item (Tester Connection) | Condition | Specified Condition |
| Electric vehicle fuse (A - B) | Always | Below 1 Ω |
| *a | Electric Vehicle Fuse |
|
| ||||
| OK | |
| 7.INSPECT NO. 2 ENGINE WIRE |
Disconnect the No. 2 engine wire connector (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D1-1 (PE) - D2-2 (ACPE) | Always | Below 1 Ω |
| D1-2 (PB) - D2-1 (ACPB) | Always | Below 1 Ω |
| D1-1 (PE) - Body ground | Always | 10 kΩ or higher |
| D1-2 (PB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY |
Replace the compressor with motor assembly (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1498/98 is not output | A |
| DTC B1498/98 is output | B |
|
| ||||
| A | ||
| ||