DTC C1202/68 Master Reservoir Level Malfunction |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| C1202/68 | 371 | An open is detected in the switch signal circuit for 2 seconds or more. |
|
| ↑ | - | The reservoir level remains low. |
|

| 1.CHECK BRAKE FLUID LEVEL |
Check that the brake fluid level is sufficient.
Check for brake fluid leaks (Connection between the brake booster pump assembly, brake master cylinder reservoir assembly and brake booster with master cylinder assembly, and the brake booster with master cylinder assembly and wheel cylinders).
Check that the DTC is not output again (Click here).
Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.
Bleed the air from the brake system (Click here).
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Select the Data List on the Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Accumulator Sensor | Accumulator pressure sensor / Min.: 0.00 V, Max.: 5.00 V | Specified value: 2.90 to 4.20 V | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
Wait for 30 seconds without depressing the brake pedal.
Check that the accumulator pressure sensor output value change is within the specified range.
|
| ||||
| OK | |
| 2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
![]() |
Turn the ignition switch off.
Remove the reservoir filler cap.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (+) - 1 (E) | Brake fluid level warning switch OFF (Float up) | 1.84 to 2.16 kΩ |
| 2 (+) - 1 (E) | Brake fluid level warning switch ON (Float down) | Below 1 Ω |
| *a | Component without harness connected (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly)) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-36 (LBL) - A27-2 (+) | Always | Below 1 Ω |
| A41-36 (LBL) - Body ground | Always | 10 kΩ or higher |
| A27-1 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT SKID CONTROL ECU (SWITCH INPUT) |
![]() |
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A27-2 (+) - Body ground | Ignition switch ON (IG) | 4 to 7 V |
| *a | Front view of wire harness connector (to Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly)) |
|
| ||||
| OK | |
| 5.CHECK BRAKE DISC |
Turn the ignition switch off.
Reconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Disconnect the brake pedal stroke sensor assembly connector.
Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.
|
| ||||
| OK | |
| 6.RECONFIRM DTC |
Reconnect the brake pedal stroke sensor assembly connector.
Clear the DTCs (Click here).
Turn the ignition switch to ON (READY).
Perform a road test.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1202/68 is not output. | A |
| DTC C1202/68 is output. | B |
|
| ||||
| A | ||
| ||