Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1391/69    Accumulator Leak Malfunction

for Preparation Click here


DESCRIPTION

The DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1391/69
351
Either of the following is detected:
  1. Accumulator pressure sensor input does not increase before braking or while the pump motor is operating.
  2. Accumulator pressure sensor input reduction rate exceeds the specification before braking and while the pump motor is not operating.
  1. Brake fluid leaks
  2. Brake actuator (Brake booster with master cylinder assembly)
    (Malfunctioning internal seal, low gas pressure in accumulator, etc.)

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK FOR FLUID LEAK
  1. Check that there are no fluid leaks in the brake lines between the brake actuator (brake booster with master cylinder assembly) and the wheel cylinders.

  1. Check that the brakes are not dragging.

    OK:
    There are no fluid leaks or dragging.



NG
REPAIR OR REPLACE APPLICABLE PART
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON (READY).

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1391/69 is output.
    A
    DTC C1391/69 is not output.
    B



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (SOLENOID VALVE)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Select the Active Test on the Techstream (Click here).

    HINT:
    The Active Test can be performed when the following conditions are met.
    1. ABS main relay is on.
    2. Shift lever is in P.
    3. Parking brake is applied.
    4. Vehicle speed is 0 km/h (0 mph).


    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Solenoid (SMC/SRC/SCC)
    Switching solenoid valve (SMC/SRC/SCC)
    Solenoid ON/OFF
    Operation sound of solenoid (clicking sound) can be heard
    *: Electronically Controlled Brake System

  1. Perform the Active Test of the solenoid using the Techstream.

  1. Select the Data List on the Techstream (Click here).


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Wheel Cylinder Pressure Sensor
Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 0.10 to 0.90 V
Reading increases when brake pedal is depressed
  1. Check that the output value of the wheel cylinder pressure sensor does not increase.

    OK:
    The output value of the wheel cylinder pressure sensor does not increase.

    HINT:
    If the output value increases, there may be brake fluid leaks in the brake actuator.


    Result:

    Result
    Proceed to
    The output value of the wheel cylinder pressure sensor increases.
    A
    The output values of the wheel cylinder pressure sensor does not increase.
    B



B
REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)
A


4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
  1. Replace the brake actuator (brake booster with master cylinder assembly) (Click here).


NEXT

REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)