Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > EVAP System

for Preparation Click here


RELATED DTCS


DTC No.
Monitoring Item
See page
P043E
Reference orifice clogged (built into canister pump module)
Click here
P043F
Reference orifice high-flow (built into canister pump module)
P0441
  1. Purge VSV (Vacuum Switching Valve) stuck closed
  2. Purge VSV stuck open
  3. Purge flow
Click here
P0451
Canister pressure sensor (built into canister pump module) signal noise
Click here
P0452
Canister pressure sensor (built into canister pump module) voltage low
P0453
Canister pressure sensor (built into canister pump module) voltage high
P0455
EVAP gross leak
Click here
P0456
EVAP small leak
P2401
Leak detection pump stuck off (built into canister pump module)
Click here
P2402
Leak detection pump stuck on (built into canister pump module)
P2419
Vent valve stuck closed (built into canister pump module)
P2420
Vent valve stuck open (vent) (built into canister pump module)
Click here
P2610
Soak timer (built into ECM)
Click here
If any EVAP system DTCs are output, the malfunctioning area can be determined using the table below.

A216743E02

NOTICE:
If the reference pressure difference between the first and second checks is more than the specification, all the DTCs relating to the reference pressure (P043E, P043F, P2401, P2402 and P2419) will all be stored.


DESCRIPTION


A269881E01


Text in Illustration 
*1
Purge VSV
*2
Fuel Vapor Feed Hose (EVAP Hose) (to Intake Manifold)
*3
Fuel Vapor Feed Hose (EVAP Hose) (from Canister)
*4
Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
*5
Canister
*6
No. 1 Canister
*7
Canister Filter
*8
Air Inlet Port
*9
Fuel Cap
*10
Fuel Tank
*a
Location of EVAP (Evaporative Emission) System
*b
Purge Line

HINT:
The canister pressure sensor, the leak detection pump and the vent valve are built into the canister pump module.


A269986E01


Text in Illustration 
*1
Canister Pump Module
*2
Intake Manifold
*3
Purge VSV
*4
Throttle Valve
*5
Canister
*6
No. 1 Canister
*7
Cut-off Valve
*8
Fuel Tank
*9
Air Cleaner
*10
ECM
*11
Canister Filter
*12
Soak Timer
*13
Fuel Cap
-
-
*a
EVAP System Circuit
-
-

NOTICE:
In the EVAP system of this vehicle, turning on the vent valve does not seal off the EVAP system. To check for leaks in the EVAP system, disconnect the air inlet vent hose and apply pressure from the atmospheric side of the canister.

While the engine is running, if a predetermined condition (closed-loop, etc.) is met, the purge VSV is opened by the ECM and fuel vapors stored in the canister are purged to the intake manifold. The ECM changes the duty cycle ratio of the purge VSV to control purge flow volume.
The purge flow volume is also determined by the intake manifold pressure. Atmospheric pressure is allowed into the canister through the vent valve to ensure that the purge flow is maintained when negative pressure (vacuum) is applied to the canister.
The following two monitors run to confirm appropriate EVAP system operation.

Key-off monitor
This monitor checks for EVAP (evaporative emission) system leaks and canister pump module malfunctions. The monitor starts 5 hours* after the ignition switch is turned off. At least 5 hours are required for the fuel to cool down to stabilize the EVAP pressure, thus making the EVAP system monitor more accurate.
The leak detection pump creates negative pressure (vacuum) in the EVAP system and the pressure is measured. Finally, the ECM monitors for leaks from the EVAP system, and malfunctions in both the canister pump module and purge VSV based on the EVAP pressure.

HINT:
*: If the engine coolant temperature is not less than 35°C (95°F) 5 hours after the ignition switch is turned off, the monitor check starts 2 hours later. If it is still not less than 35°C (95°F) 7 hours after the ignition switch is turned off, the monitor check starts 2.5 hours later.


Purge flow monitor
The purge flow monitor consists of the 2 monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.
  1. The 1st monitor
    While the engine is running and the purge VSV (Vacuum Switching Valve) is on (open), the ECM monitors the purge flow by measuring the EVAP pressure change. If negative pressure is not created, the ECM begins the 2nd monitor.
  2. The 2nd monitor
    The vent valve is turned on (closed) and the EVAP pressure is then measured. If the variation in the pressure is less than 0.5 kPa(gauge) [3.751 mmHg(gauge)], the ECM interprets this as the purge VSV being stuck closed, illuminates the MIL and stores DTC P0441 (2 trip detection logic).
  1. Atmospheric pressure check:
    1. In order to ensure reliable malfunction detection, the variation between the atmospheric pressures, before and after of the purge flow monitor, is measured by the ECM.

A216103E07


Text in Illustration 
*1
ECM
*2
Soak Timer
*3
Fuel Cap
*4
Canister Filter
*5
Fuel Tank
*6
Canister Pressure Sensor
*7
Canister Pump Module
*8
Canister
*9
No. 1 Canister
-
-
*a
EVAP Purge Flow
*b
to Intake Manifold
*c
Purge VSV: on
*d
Leak Detection Pump: off
*e
Reference Orifice (0.02 inch)
*f
Vent Valve: off

Component
Operation
Canister, No. 1 canister
Contains activated charcoal to absorb EVAP (Evaporative Emissions) generated in fuel tank.
Cut-off valve
Located in fuel tank. Valve floats and closes when fuel tank is 100% full.
Purge VSV (Vacuum Switching Valve)
Opens or closes line between canister and intake manifold. ECM uses purge VSV to control EVAP purge flow. In order to discharge EVAP absorbed by canister to intake manifold, ECM opens purge VSV. EVAP discharge volume to intake manifold controlled by purge VSV duty cycle (current-carrying time). (Open: on, Close: off)
Soak timer
Built into ECM. To ensure accurate EVAP monitor, measures 5 hours (+/-15 min) after ignition switch is turned off. This allows fuel to cool down, stabilizing EVAP pressure. When approximately 5 hours elapsed, ECM activates (refer to fig. 3).
Canister pump module
Consists of (a) to (d) below. Canister pump module cannot be disassembled.
(a) Vent valve
Vents and closes EVAP system. When ECM turns valve on, EVAP system is closed. When ECM turns valve off, EVAP system is vented. Negative pressure (vacuum) is created in EVAP system to check for EVAP leaks by closing purge VSV, turning on vent valve (closing it) and operating leak detection pump (refer to fig. 1).
(b) Canister pressure sensor
Indicates pressure as voltages. ECM supplies regulated 5 V to pressure sensor, and uses feedback from sensor to monitor EVAP system pressure (refer to fig. 2).
(c) Leak detection pump
Creates negative pressure (vacuum) in EVAP system for leak check.
(d) Reference orifice
Has opening with 0.02 inch diameter. Vacuum is produced through orifice by closing purge VSV, turning off vent valve and operating leak detection pump, to monitor reference pressure. Reference pressure is used when checking for small EVAP leaks.

A207995E05


Text in Illustration 
*1
Canister
*2
Reference Orifice (0.02 Inch)
*3
Canister Pressure Sensor
-
-
*a
Canister Pump Module (fig. 1)
*b
Airflow
*c
Condition: Purge Flow
*d
Condition: Leak Check
*e
Vent Valve: Off (vent)
*f
to Canister Filter (Atmosphere)
*g
Leak Detection Pump: Off
*h
Vent Valve: On (closed)
*i
Leak Detection Pump: On
-
-

A115543E99


A275612E02


WIRING DIAGRAM

Refer to DTC P0451 .

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. The Techstream is required to conduct the following diagnostic troubleshooting procedure.

HINT:
  1. Using the Techstream monitor results enables the EVAP (Evaporative Emission) system to be confirmed.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CONFIRM DTC
  1. Turn the ignition switch off and wait for 10 seconds.

  1. Turn the ignition switch to ON (IG).

  1. Turn the ignition switch off and wait for 10 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



  1. Confirm DTCs and freeze frame data.
    If any EVAP system DTCs are set, the malfunctioning area can be determined using the table below.


    A216743E02

    NOTICE:
    If the reference pressure difference between the first and second checks is greater than the specification, all the DTCs relating to the reference pressure (P043E, P043F, P2401, P2402 and P2419) are stored.


NEXT


2.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine during this operation.
  4. When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the temperature less than 35°C (95°F).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

  1. After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.

    HINT:
    If no pending DTCs are displayed, perform the Confirmation Driving Pattern. After this confirmation, check for pending DTCs. If no DTCs are displayed, the EVAP system is normal.


NEXT


3.PERFORM EVAPORATIVE SYSTEM CHECK (MANUAL MODE)

A227234E10

NOTICE:
  1. In the Evaporative System Check (Manual Mode), the series of 6 Evaporative System Check steps are performed manually using the Techstream.
  2. Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine during this operation.
  4. When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the temperature less than 35°C (95°F).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Manual Mode.


NEXT


4.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6)

A106736E58

  1. Check the EVAP pressure in step 1/6.

    Result 
    DTC
    *1
    Result
    Suspected Trouble Area
    Proceed to
    -
    Virtually no variation in EVAP pressure
    Not yet determined
    A
    P0451
    EVAP pressure fluctuates by +/-0.3 kPa(gauge) [2.25 mmHg(gauge)] or higher
    Canister pressure sensor signal noise
    B
    (P0452 or P0453)
    *2
    1. EVAP pressure is below 42.11 kPa(abs) [315.867 mmHg(abs)], or higher than 123.761 kPa(abs) [928.331 mmHg(abs)]
    2. EVAP pressure deviates +/-10 kPa(gauge) [+/-75 mmHg(gauge)] from actual atmosphere pressure *3
    Canister pressure sensor or its circuit has malfunction
    C

    1. *1: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.
    2. *2: If the canister pressure sensor circuit has an open or short, DTC P0452 or P0453 is stored 0.5 seconds after the ignition switch is turned to ON (IG).

    HINT:
    *3: Canister pressure sensor standard output range is 70 to 110 kPa(abs) [525 to 825 mmHg(abs)]. This varies by weather.



B
Go to step 40

C
Go to step 12
A


5.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6 TO 2/6)

A106737E62

  1. Check the EVAP pressure in steps 1/6 and 2/6.

    Result 
    DTC*
    Result
    Suspected Trouble Area
    Proceed to
    -
    Virtually no variation in EVAP pressure during step 1/6. Then decreases to reference pressure
    Not yet determined
    A
    P2402
    Small difference between EVAP pressures during steps 1/6 and 2/6
    Leak detection pump stuck ON
    B
    *: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.

    HINT:
    The first reference pressure is the value determined in step 2/6.



B
Go to step 32
A


6.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6)

A106738E60

HINT:
Make a note of the pressures checked in inspection items (A) and (B) below.

  1. Check the EVAP pressure 4 seconds after the leak detection pump is activated*1 (A).
    *1: The leak detection pump begins to operate as step 1/6 finishes and step 2/6 starts.

  1. Check the EVAP pressure again when it has stabilized. This pressure is the reference pressure (B).

    Result 
    DTC*2
    Result
    Suspected Trouble Area
    Proceed to
    -
    EVAP pressure in inspection item (B) is between -4.85 kPa(gauge) and -1.057 kPa(gauge) [-36.38 mmHg(gauge) and -7.929 mmHg(gauge)]
    Not yet determined
    A
    P043F and P2401
    EVAP pressure in inspection item (B) is -1.057 kPa(gauge) [-7.929 mmHg(gauge)] or higher
    1. Reference orifice high-flow
    2. Leak detection pump stuck OFF
    B
    P043E
    EVAP pressure in inspection item (B) is less than -4.85 kPa(gauge) [-36.38 mmHg(gauge)]
    Reference orifice clogged
    C
    P2419
    EVAP pressure in inspection item (A) is higher than -0.25 kPa(gauge) [-1.875 mmHg(gauge)]
    1. Vent valve stuck closed
    2. Leak detection pump performance deteriorates
    3. Leak detection pump circuit malfunctioning (large resistance exists in the circuit)
    D
    *2: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.



B
Go to step 11

C
Go to step 40

D
Go to step 13
A


7.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6 TO 3/6)

A106739E38

  1. Check the EVAP pressure in step 3/6.

    Result 
    DTC*
    Result
    Suspected Trouble Area
    Proceed to
    -
    EVAP pressure increases by 0.3 kPa(gauge) [2.25 mmHg(gauge)] or higher within 10 seconds of proceeding from step 2/6 to step 3/6
    Not yet determined
    A
    P2420
    No variation in EVAP pressure even after proceeding from step 2/6 to step 3/6
    1. Vent valve stuck open (vent)
    2. Canister (charcoal filter inside canister) clogged
    3. No. 1 canister (charcoal filter inside canister) clogged
    B
    *: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.



B
Go to step 28
A


8.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6)

A106740E27

  1. Wait until the EVAP pressure change is less than 0.12 kPa(gauge) [0.9 mmHg(gauge)] for 40 seconds.

  1. Measure the EVAP pressure and record it.

    HINT:
    A few minutes are required for the EVAP pressure to become saturated. When there is little fuel in the fuel tank, it takes up to 15 minutes.


NEXT


9.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 4/6)

A106741E37

  1. Check the EVAP pressure in step 4/6.

    Result 
    DTC*1
    Result
    Suspected Trouble Area
    Proceed to
    -
    EVAP pressure increases by 0.3 kPa(gauge) [2.25 mmHg(gauge)] or higher within 10 seconds of proceeding from step 3/6 to step 4/6
    Not yet determined
    A
    P0441
    *2
    EVAP pressure increases by 0.3 kPa(gauge) [2.25 mmHg(gauge)] or higher more within 10 seconds of proceeding from step 3/6 to step 4/6
    1. Purge VSV
    2. Purge VSV circuit
    3. Problems in EVAP hose between purge VSV and intake manifold
    4. Problems in EVAP hose between canister and purge VSV
    5. ECM
    B
    P0441
    Variation in EVAP pressure is less than 0.3 kPa(gauge) [2.25 mmHg(gauge)] for 10 seconds, after proceeding from step 3/6 to step 4/6
    1. Purge VSV stuck closed
    2. Purge VSV circuit
    3. Canister (charcoal filter inside canister) clogged
    4. No. 1 canister (charcoal filter inside canister) clogged
    5. Problems in EVAP hose between purge VSV and intake manifold
    6. Problems in EVAP hose between canister and purge VSV
    7. ECM
    C

    1. *1: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.
    2. *2: This result suggests that due to purge line blockage or purge VSV malfunction, the DTC was stored by the purge flow monitor while the engine was running, or that key-off monitor test result were nearly borderline values.



B
Go to step 23

C
Go to step 17
A


10.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 5/6)

A241391E01

  1. Check the EVAP pressure in step 5/6.

  1. Compare the EVAP pressure in step 3/6 and the second reference pressure (step 5/6).

    Result 
    DTC*
    Result
    Suspected Trouble Area
    Proceed to
    -
    EVAP pressure from step 3/6 lower than second reference pressure (step 5/6)
    Not yet determined (no leakage from EVAP system)
    A
    P0441 and P0455
    EVAP pressure from step 3/6 higher than [second reference pressure (step 5/6) x 0.2]
    1. Purge VSV stuck open
    2. EVAP gross leak
    B
    P0456
    EVAP pressure from step 3/6 higher than second reference pressure (step 5/6)
    EVAP small leak
    B
    *: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.



A
Go to step 45

B
Go to step 17

11.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6)

A106742E30

  1. Check the EVAP pressure in step 3/6.

    Result 
    DTC*
    Result
    Suspected Trouble Area
    Proceed to
    P043F
    EVAP pressure less than [reference pressure] measured in step 2/6
    Reference orifice high-flow
    A
    P2401
    EVAP pressure almost same as [reference pressure] measured in step 2/6
    Leak detection pump stuck off
    B
    *: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.

    HINT:
    The first reference pressure is the value determined in step 2/6.



A
Go to step 40

B
Go to step 33

12.INSPECT CANISTER PUMP MODULE (CANISTER PRESSURE SENSOR CIRCUIT)
  1. Check the canister pressure sensor circuit, referring to DTC P0451 canister pressure sensor circuit inspection procedure .



NEXT
Go to step 52

13.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
  1. Turn the ignition switch off.



    A269880E01
  1. Disconnect the canister pump module connector.
    Text in Illustration 
    *a
    Component without harness connected
    (Canister Pump Module)

  1. Apply the auxiliary battery voltage to terminals VLVB and VGND of the canister pump module.

  1. Touch the canister pump module to confirm the vent valve operation.

    Result 
    Condition
    Tester Result
    Suspected Trouble Area
    Proceed to
    Apply auxiliary battery voltage to terminals VLVB and VGND
    Operating
    1. Wire harness or connector between vent valve and ECM
    2. Leak detection pump performance deteriorates
    3. Leak detection pump circuit malfunctioning (large resistance exists in the circuit)
    4. ECM
    A
    Not operating
    Vent valve
    B



B
Go to step 40
A


14.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Disconnect the canister pump module connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    M21-1 (VGND) - A40-5 (VPMP)
    Always
    Below 1 Ω
    M21-1 (VGND) or A40-5 (VPMP) - Body ground
    Always
    10 kΩ or higher


    Result 
    Result
    Suspected Trouble Area
    Proceed to
    OK
    1. Leak detection pump performance deteriorates
    2. Leak detection pump circuit malfunctioning (large resistance exists in the circuit)
    3. ECM
    A
    NG
    Wire harness or connector between ECM and canister pump module
    B



B
Go to step 42
A


15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
  1. Disconnect the canister pump module connector.

  1. Measure the resistance according to the value(s) in the table below.


Result 
Tester Connection
Condition
Specified Condition
Suspected Trouble Area
Proceed to
M21-4 (MGND) - Body ground
Always
Below 1 Ω
  1. Canister pump module
  2. Wire harness or connector between canister pump module and ECM
  3. ECM
A
10 kΩ or higher
Wire harness or connector between canister pump module and body ground
B


B
Go to step 42
A


16.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
  1. Disconnect the canister pump module connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.


Result 
Tester Connection
Condition
Specified Condition
Suspected Trouble Area
Proceed to
A40-18 (MPMP) - M21-3 (MTRB)
Always
Below 1 Ω
  1. Canister pump module
  2. ECM
A
10 kΩ or higher
Wire harness or connector between ECM and canister pump module
B


A
Go to step 47

B
Go to step 42

17.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE VSV FOR EVAP CONTROL)
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.



    A269882E01
  1. Disconnect the fuel vapor feed hose (connected to the canister) from the purge VSV.
    Text in Illustration 
    *1
    Purge VSV
    *2
    Fuel Vapor Feed Hose (to Canister)

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Using the Techstream, turn off the purge VSV (Activate the VSV for Evap Control: OFF).

  1. Use your finger to confirm that the purge VSV has no suction.

  1. Using the Techstream, turn on the purge VSV (Activate the VSV for Evap Control: ON).

  1. Use your finger to confirm that the purge VSV has suction.

    Result 
    Test Result
    Suspected Trouble Area
    Proceed to
    No suction when purge VSV turned off, and suction applied when turned on
    Blockage in the purge line is considered (based on result of step 9):
    1. Problems with EVAP hose between canister and purge VSV
    2. Canister (charcoal filter inside canister) clogged
    3. No. 1 canister (charcoal filter inside canister) clogged
    4. ECM
    A
    Leakage is considered (based on result of step 10):
    1. Fuel cap
    2. Leakage from EVAP line, fuel tank, canister, or No. 1 canister
    B
    Suction applied when purge VSV turned off
    1. Purge VSV stuck open
    C
    No suction when purge VSV turned on
    1. Purge VSV stuck closed
    2. Problems with EVAP hose between purge VSV and intake manifold
    D



B
Go to step 21

C
Go to step 22

D
Go to step 24
A


18.INSPECT EVAP HOSE (PURGE VSV - CANISTER)
  1. Check for blockages in the EVAP purge line between the purge VSV and canister.

    OK:
    No blockages in the EVAP purge line between the purge VSV and canister.



NG
Go to step 46
OK


19.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER)
  1. Check for filter blockage in the canister .

    OK:
    No blockages in the canister.



NG
Go to step 50
OK


20.INSPECT NO. 1 CANISTER (CHARCOAL FILTER INSIDE CANISTER)
  1. Check for filter blockage in the No. 1 canister .

    OK:
    No blockages in the No. 1 canister.



OK
Go to step 49

NG
Go to step 51

21.CHECK FUEL CAP
  1. Check that the fuel cap is correctly installed and confirm that the fuel cap meets OEM specifications.

  1. Tighten the fuel cap firmly (only one click sound could be heard).

    HINT:
    If an EVAP tester is available, check the fuel cap using the tester.

    1. Remove the fuel cap and install it onto a fuel cap adapter.

    2. Connect an EVAP tester pump hose to the adapter, and pressurize the cap to 3.2 to 3.7 kPa(gauge) [24 to 27.75 mmHg(gauge)] using an EVAP tester pump.

    3. Seal the adapter and wait for 2 minutes.

    4. Check the pressure. If the pressure is 2 kPa(gauge) [15 mmHg(gauge)] or higher, the fuel cap is normal.

      Result 
      Test Result
      Suspected Trouble Area
      Proceed to
      Fuel cap correctly installed
      -
      A
      Fuel cap loose
      1. Fuel cap improperly installed
      2. Defective fuel cap
      3. Fuel cap does not meet OEM specifications
      B
      Defective fuel cap
      -
      B
      No fuel cap
      -
      C



A
Go to step 39

B
Go to step 37

C
Go to step 38

22.INSPECT PURGE VSV
  1. Turn the ignition switch off.



    A269883E01
  1. Disconnect the purge VSV connector.
    Text in Illustration 
    *1
    Fuel Vapor Feed Hose (to Canister)
    *2
    Connector
    *3
    Purge VSV

  1. Disconnect the fuel vapor feed hose (connected to the canister) from the purge VSV.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Use your finger to confirm that the purge VSV has no suction.

    Result 
    Test Result
    Suspected Trouble Area
    Proceed to
    No suction
    1. Wire harness or connector between purge VSV and ECM
    2. ECM
    A
    Suction applied
    Purge VSV
    B



A
Go to step 27

B
Go to step 41

23.INSPECT EVAP HOSE (PURGE VSV - CANISTER)
  1. Check for blockages in the EVAP purge line between the purge VSV and canister.

    OK:
    No blockages in the EVAP purge line between the purge VSV and canister.



NG
Go to step 46
OK


24.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD)


    A269884E01
  1. Disconnect the fuel vapor feed hose (connected to the intake manifold) from the purge VSV.
    Text in Illustration 
    *1
    Purge VSV
    *2
    Fuel Vapor Feed Hose (to intake manifold)

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Use your finger to confirm that the fuel vapor feed hose has suction.

    Result 
    Test Result
    Suspected Trouble Area
    Proceed to
    Suction applied
    EVAP hose between purge VSV and intake manifold normal
    1. Purge VSV
    2. Purge VSV power source
    3. Wire harness or connector between purge VSV and ECM
    A
    No suction
    1. Intake manifold port
    2. EVAP hose between purge VSV and intake manifold
    B



B
Go to step 36
A


25.INSPECT PURGE VSV
  1. Remove the purge VSV.



    A166966E09
  1. Apply auxiliary battery voltage to the terminals of the purge VSV.
    Text in Illustration 
    *1
    Purge VSV

  1. Confirm that air flows from port E to port F.

    Result 
    Test Result
    Condition
    Suspected Trouble Area
    Proceed to
    Air flows
    Auxiliary battery voltage is applied to purge VSV terminals
    Purge VSV normal
    1. Purge VSV power source
    2. Wire harness or connector between purge VSV and ECM
    A
    No air flow
    Auxiliary battery voltage is applied to purge VSV terminals
    Purge VSV
    B



B
Go to step 41
A


26.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
  1. Disconnect the purge VSV connector.



    A194112E60
  1. Turn the ignition switch to ON (IG).
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Purge VSV)

  1. Measure the voltage according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    C19-1 - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    Purge VSV power source normal
    1. Wire harness or connector between purge VSV and ECM
    A
    Other than result above
    Wire harness or connectors between purge VSV and auxiliary battery
    B



B
Go to step 42
A


27.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the purge VSV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C19-2 - C10-76 (PRG)
    Always
    Below 1 Ω
    C19-2 or C10-76 (PRG) - Body ground
    Always
    10 kΩ or higher



OK
Go to step 49

NG
Go to step 42

28.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE)


  1. Turn the ignition switch off.


    A269878E02


Text in Illustration 
*a
Front view of wire harness connector
(to Canister Pump Module)
-
-
  1. Disconnect the canister pump module connector.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    M21-5 (VLVB) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    1. Wire harness or connector between vent valve and ECM
    2. Vent valve
    3. Canister (charcoal filter inside canister) clogged
    4. No. 1 canister (charcoal filter inside canister) clogged
    5. ECM
    A
    Below 3 V
    1. Power source wire harness of vent valve
    B



B
Go to step 42
A


29.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
  1. Turn the ignition switch off.



    A269880E01
  1. Disconnect the canister pump module connector.
    Text in Illustration 
    *a
    Component without harness connected
    (Canister Pump Module)

  1. Apply the auxiliary battery voltage to terminals VLVB and VGND of the canister pump module.

  1. Touch the canister pump module to confirm the vent valve operation.

    Result 
    Condition
    Tester Result
    Suspected Trouble Area
    Proceed to
    Apply auxiliary battery voltage to terminals VLVB and VGND
    Operating
    1. Wire harness or connector between vent valve and ECM
    2. Canister (charcoal filter inside canister) clogged
    3. No. 1 canister (charcoal filter inside canister) clogged
    4. ECM
    A
    Not operating
    1. Vent valve
    B



B
Go to step 40
A


30.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Disconnect the canister pump module connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Test Result
    Suspected Trouble Area
    Proceed to
    M21-1 (VGND) - A40-5 (VPMP)
    Always
    Below 1 Ω
    1. Canister (charcoal filter inside canister) clogged
    2. ECM
    A
    10 kΩ or higher
    Wire harness or connector between ECM and canister pump module
    B



B
Go to step 42
A


31.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER)
  1. Check for filter blockage in the canister .

    OK:
    No blockages in the canister.



NG
Go to step 50
OK


32.INSPECT NO. 1 CANISTER (CHARCOAL FILTER INSIDE CANISTER)
  1. Check for filter blockage in the No. 1 canister .

    OK:
    No blockages in the No. 1 canister.



OK
Go to step 49

NG
Go to step 51

33.CHECK TERMINAL VOLTAGE (CANISTER PUMP MODULE)
  1. Turn the ignition switch off.



  1. Disconnect the canister pump module connector.


    A269878E03


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Canister Pump Module)
    -
    -

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Test Result
    Suspected Trouble Area
    Proceed to
    M21-3 (MTRB) - Body ground
    Ignition switch ON (IG)
    9 to 14 V
    1. Wire harness or connector between leak detection pump and body ground
    2. Leak detection pump
    A
    Below 3 V
    1. Wire harness or connector between leak detection pump and ECM
    2. ECM
    B



B
Go to step 35
A


34.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
  1. Turn the ignition switch off.

  1. Disconnect the canister pump module connector.

  1. Measure the resistance according to the value(s) in the table below.


Result 
Tester Connection
Condition
Specified Condition
Suspected Trouble Area
Proceed to
M21-4 (MGND) - Body ground
Always
Below 1 Ω
Leak detection pump
A
10 kΩ or higher
Wire harness or connector between canister pump module and body ground
B


A
Go to step 40

B
Go to step 42

35.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
  1. Turn the ignition switch off.

  1. Disconnect the canister pump module connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A40-18 (MPMP) - M21-3 (MTRB)
    Always
    Below 1 Ω
    A40-18 (MPMP) or M21-3 (MTRB) - Body ground
    Always
    10 kΩ or higher


Result 
Result
Suspected Trouble Area
Proceed to
OK
ECM
A
NG
Wire harness or connector between ECM and canister pump module
B


A
Go to step 49

B
Go to step 42

36.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
  1. Stop the engine.

  1. Disconnect the EVAP hose from the intake manifold.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Use your finger to confirm that the port of the intake manifold has suction.


Result 
Tester Connection
Suspected Trouble Area
Proceed to
Suction applied
EVAP hose between intake manifold and purge VSV
A
No suction
Intake manifold
B


A
Go to step 43

B
Go to step 44

37.CORRECTLY REINSTALL OR REPLACE FUEL CAP

HINT:
  1. When reinstalling the fuel cap, tighten it firmly (only one click sound could be head).
  2. When replacing the fuel cap, use a fuel cap that meets OEM specifications, and install it firmly.



NEXT
Go to step 52

38.REPLACE FUEL CAP

HINT:
When installing the fuel cap, tighten it firmly (only one click sound could be head).



NEXT
Go to step 52

39.LOCATE EVAP LEAK PART


  1. Disconnect the vent hose.


    A269879E02


    Text in Illustration 
    *1
    Fuel Tank
    *2
    Canister
    *3
    No. 1 Canister
    *4
    Canister Filter
    *5
    Fuel Cap
    *6
    Canister Pump Module
    *a
    Disconnect the vent hose
    -
    -



  1. Connect the EVAP pressure tester tool to the canister pump module with the adapter.


    A269885E01


    Text in Illustration 
    *1
    Canister Pump Module
    *2
    Adapter
    *3
    EVAP Pressure Tester Tool
    -
    -

  1. Pressurize the EVAP system to 3.2 to 3.7 kPa(gauge) [24 to 27.75 mmHg(gauge)].

  1. Apply soapy water to the piping and connecting parts of the EVAP system.

  1. Look for areas where bubbles appear. This indicates the leak point.

  1. Repair or replace the leak point.

    HINT:
    Disconnect the hose between the canister and fuel tank from the canister. Block the canister side and conduct an inspection. In this way, the fuel tank can be excluded as an area suspected of causing fuel leaks.



NEXT
Go to step 52

40.REPLACE CANISTER PUMP MODULE


  1. Replace the canister pump module .

    NOTICE:
    1. When replacing the canister pump module, check the canister pump module interior, canister interior and No. 1 canister interior related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior or No. 1 canister interior, replace the canister, No. 1 canister and canister pump module together.
    2. Check for filter blockage in the canister and No. 1 canister. If the charcoal filter inside the canister or No. 1 canister is clogged, replace the canister, No. 1 canister and canister pump module together.
    3. Check for filter blockage in the canister filter.


    A269879E03


    Text in Illustration 
    *1
    Fuel Tank Vent Hose
    *2
    Air Inlet Port
    *3
    Vent Hose
    *4
    Fuel Tank
    *5
    Canister Pump Module
    *6
    Canister
    *7
    No. 1 Canister
    *8
    Canister Filter
    *a
    Inspection Area
    (check for disconnection and/or cracks)
    -
    -



NEXT
Go to step 52

41.REPLACE PURGE VSV
  1. Replace the purge VSV (Click here).



NEXT
Go to step 52

42.REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 52

43.REPAIR OR REPLACE EVAP PURGE LINE (INTAKE MANIFOLD - PURGE VSV)


NEXT
Go to step 52

44.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
  1. Check that the EVAP purge port of the intake manifold is not clogged. If necessary, replace the intake manifold (Click here).



NEXT
Go to step 52

45.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS
  1. Repair the malfunctioning areas indicated by the DTCs that had been confirmed when the vehicle was brought in.



NEXT
Go to step 52

46.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VSV - CANISTER)


NEXT
Go to step 52

47.REPLACE CANISTER PUMP MODULE


  1. Replace the canister pump module .

    NOTICE:
    1. When replacing the canister pump module, check the canister pump module interior, canister interior and No. 1 canister interior related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior or No. 1 canister interior, replace the canister, No. 1 canister and canister pump module together.
    2. Check for filter blockage in the canister and No. 1 canister. If the charcoal filter inside the canister or No. 1 canister is clogged, replace the canister, No. 1 canister and canister pump module together.
    3. Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.


    A269879E03


    Text in Illustration 
    *1
    Fuel Tank Vent Hose
    *2
    Air Inlet Port
    *3
    Vent Hose
    *4
    Fuel Tank
    *5
    Canister Pump Module
    *6
    Canister
    *7
    No. 1 Canister
    *8
    Canister Filter
    *a
    Inspection Area
    (check for disconnection and/or cracks)
    -
    -


NEXT


48.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine in this step.
  4. When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing an Evaporative System Check, keep the fuel temperature less than 35°C (95°F).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

  1. After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.

    Result
    Proceed to
    EVAP system DTCs are output
    A
    DTC is not output
    (Pending DTC is not output)
    B



B
END
A


49.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 52

50.REPLACE CANISTER


  1. Replace the canister .

    NOTICE:
    1. When replacing the canister, check the canister pump module interior and No. 1 canister interior related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.
    2. Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.


    A269879E03


    Text in Illustration 
    *1
    Fuel Tank Vent Hose
    *2
    Air Inlet Port
    *3
    Vent Hose
    *4
    Fuel Tank
    *5
    Canister Pump Module
    *6
    Canister
    *7
    No. 1 Canister
    *8
    Canister Filter
    *a
    Inspection Area
    (check for disconnection and/or cracks)
    -
    -



NEXT
Go to step 52

51.REPLACE NO. 1 CANISTER


  1. Replace the No. 1 canister .

    NOTICE:
    1. When replacing the No. 1 canister, check the canister pump module interior and canister interior related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.
    2. Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.


    A269879E03


    Text in Illustration 
    *1
    Fuel Tank Vent Hose
    *2
    Air Inlet Port
    *3
    Vent Hose
    *4
    Fuel Tank
    *5
    Canister Pump Module
    *6
    Canister
    *7
    No. 1 Canister
    *8
    Canister Filter
    *a
    Inspection Area
    (check for disconnection and/or cracks)
    -
    -


NEXT


52.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine in this step.
  4. When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing an Evaporative System Check, keep the fuel temperature below 35°C (95°F).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

  1. After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.

    HINT:
    If no pending DTCs are found, the repair has been successfully completed.


NEXT

END 


CONFIRMATION DRIVING PATTERN

HINT:
After a repair, check Monitor Status by performing the Key-Off Monitor Confirmation and Purge Flow Monitor Confirmation described below.


KEY-OFF MONITOR CONFIRMATION
  1. Preconditions
    The monitor will not run unless:

    1. The vehicle has been driven for 10 minutes or more (in a city area or on a freeway).
    2. The fuel tank is less than 90% full.
    3. The altitude is less than 2400 m (7874 ft).
    4. The engine coolant temperature is between 4.4 and 35°C (40 and 95°F).
    5. The intake air temperature is between 4.4 and 35°C (40 and 95°F).
    6. The vehicle remains stationary (the vehicle speed is 0 km/h [0 mph]).

  2. Monitor Conditions

    1. Allow the engine to idle for at least 5 minutes.
    2. Turn the ignition switch off and wait for 6 hours (8 or 10.5 hours).

      HINT:
      Do not start the engine until checking Monitor Status. If the engine is started, the steps described above must be repeated.

  3. Monitor Status

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
    5. Check the Monitor Status displayed on the Techstream.

      HINT:
      If Incomplete is displayed, the monitor did not complete. Make sure that the preconditions have been met, and perform the Monitor Conditions again.


PURGE FLOW MONITOR CONFIRMATION (P0441)

HINT:
Perform this monitor confirmation after the Key-Off Monitor Confirmation shows Complete.

  1. Preconditions
    The monitor will not run unless:

    1. The vehicle has been driven for 10 minutes or more (in a city area or on a freeway).
    2. The engine coolant temperature is 4.4°C (40°F) or higher.
    3. The intake air temperature is 4.4°C (40°F) or higher.

  2. Monitor Conditions

    1. Release the pressure from the fuel tank by removing and reinstalling the fuel tank cap assembly.
    2. Warm the engine up until the engine coolant temperature reaches higher than 75°C (167°F).
    3. Increase the engine speed to 2500 rpm once.
    4. Allow the engine to idle and turn the A/C switch on for 1 minute.

  3. Monitor Status

    1. Turn the ignition switch off (if ON (IG)) or if the engine is running).
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
    6. Check the Monitor Status displayed on the Techstream.

      HINT:
      If Incomplete is displayed, the monitor did not complete. Make sure that the preconditions have been met, and perform the Monitor Conditions again.


MONITOR RESULT

Refer to detailed information in Checking Monitor Status (Click here).

P0456: Evaporative System / SMALL LEAK 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$C9
Multiply by 0.001
kPa
Test value for small leak

P0455: Evaporative System / GROSS LEAK 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$CA
Multiply by 0.001
kPa
Test value for gross leak

P2401: Evaporative System / VACUUM PMP OFF 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$CB
Multiply by 0.001
kPa
Test value for leak detection pump stuck OFF

P2402: Evaporative System / VACUUM PMP ON 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$CD
Multiply by 0.001
kPa
Test value for leak detection pump stuck ON

P2420: Evaporative System / VENT VALVE OFF 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$CE
Multiply by 0.001
kPa
Test value for vent valve stuck OFF

P2419: Evaporative System / VENT VALVE ON 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$CF
Multiply by 0.001
kPa
Test value for vent valve stuck ON

P043E: Evaporative System / ORIFICE CLOGGED 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$D0
Multiply by 0.001
kPa
Test value for reference orifice low flow

P043F: Evaporative System / ORIFICE HI-FLW 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$D1
Multiply by 0.001
kPa
Test value for reference orifice high flow

P0441: Evaporative System / PURGE VSV CLOSED 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$D4
Multiply by 0.001
kPa
Test value for purge VSV stuck closed

P0441: Evaporative System / PURGE VSV OPENED 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$D5
Multiply by 0.001
kPa
Test value for purge VSV stuck open

P0441: Evaporative System / PURGE FLOW 
Monitor ID
Test ID
Scaling
Unit
Description
$3D
$D7
Multiply by 0.001
kPa
Test value for purge flow insufficient