Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and also the radio and display receiver assembly itself cannot function.

WIRING DIAGRAM


E250531E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
  1. Disconnect the radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G78-21 (SW1) - Body ground
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    323 to 335 Ω
    Volume+ switch pushed
    980 to 1020 Ω
    Volume- switch pushed
    3048 to 3172 Ω
    G78-22 (SW2) - Body ground
    No switch pushed
    95 to 105 kΩ
    MODE switch pushed
    Below 2.5 Ω
    On hook switch pushed
    323 to 335 Ω
    Off hook switch pushed
    980 to 1020 Ω
    Voice switch pushed
    3048 to 3172 Ω



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Disconnect the steering pad switch assembly connector.


    E232590E04

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-10 (AU1) - z2-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    323 to 335 Ω
    Volume+ switch pushed
    980 to 1020 Ω
    Volume- switch pushed
    3048 to 3172 Ω
    z2-9 (AU2) - z2-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE switch pushed
    Below 2.5 Ω
    On hook switch pushed
    323 to 335 Ω
    Off hook switch pushed
    980 to 1020 Ω
    Voice switch pushed
    3048 to 3172 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Seek+
    *c
    Seek-
    *d
    Volume+
    *e
    Volume-
    *f
    MODE
    *g
    Voice
    *h
    On hook
    *i
    Off hook
    -
    -

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 4
A


3.INSPECT STEERING PAD SWITCH RH


  1. Disconnect the steering pad switch RH connectors.


    E250441E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SR1-3 (AU1) - z2-10 (AU1)
    Always
    Below 1 Ω
    SR1-5 (EAU) - z2-8 (EAU)
    Always
    Below 1 Ω
    SR1-4 (AU2) - z2-9 (AU2)
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch RH)
    -
    -



NG
REPLACE STEERING PAD SWITCH RH (Click here)
OK

REPLACE STEERING PAD SWITCH LH (Click here)  

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.

  1. Disconnect the spiral cable with sensor sub-assembly connector.



    E230425E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - G5-4 (EAU)
    Center
    Below 3 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-10 (AU1) - G5-6 (AU1)
    Center
    Below 3 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-9 (AU2) - G5-5 (AU2)
    Center
    Below 3 Ω
    2.5 rotations to the left
    2.5 rotations to the right

  1. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - G5-4 (EAU)
    Always
    Below 3 Ω
    z2-10 (AU1) - G5-6 (AU1)
    Always
    Below 3 Ω
    z2-9 (AU2) - G5-5 (AU2)
    Always
    Below 3 Ω

    NOTICE:
    1. The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
    2. As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable with Sensor Sub-assembly)
    *b
    Steering Pad Switch Assembly Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, BODY GROUND - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)