DTC B1497/97 BUS IC Communication Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1497/97 | Error or open in communication line |
|

| 1.PERFORM ACTIVE TEST USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Air Conditioner / Active test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Air Mix Servo Targ Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix) pulse | Min.: 128, Max.: 383 | Operates between 173 and 257 pulses |
| Air Outlet Servo Pulse (D) | No. 2 air conditioning radiator damper servo sub-assembly (air outlet) pulse | Min.: 128, Max.: 383 | Operates between 206 and 267 pulses |
| Air Inlet Damper Targ Pulse | No. 1 blower damper servo sub-assembly (air inlet) pulse | Min.: 128, Max.: 383 | Operates between 254 and 287 pulses |
According to the test result, proceed to the next step.
| Result | Proceed to |
| One of the damper servo motors is malfunctioning | A |
| All of the damper servo motors are malfunctioning | B |
|
| ||||
| A | |
| 2.SYSTEM CHECK |
According to the test result, proceed to the next step.
| Result | Proceed to |
| Only the No. 1 air conditioning radiator damper servo sub-assembly (air mix) is malfunctioning | A |
| Only the No. 1 blower damper servo sub-assembly (air inlet) is malfunctioning | B |
| Only the No. 2 air conditioning radiator damper servo sub-assembly (air outlet) is malfunctioning | C |
|
| ||||
|
| ||||
| A | |
| 3.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX) |
Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix) (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 4.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET) |
Replace the No. 1 blower damper servo sub-assembly (air inlet) (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 5.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET) |
Replace the No. 2 air conditioning radiator damper servo sub-assembly (air outlet) (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY |
Replace the air conditioning harness assembly (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) |
Disconnect the G34 air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G34-21 (B) - Body ground | Ignition switch off | 11 to 14 V |
|
| ||||
| OK | ||
| ||