Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System) > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The door control and tire pressure monitoring system receiver assembly receives signals from the door control transmitter module set sub-assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM


B297339E04


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the door control and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the Techstream and write them down before removal (Click here).
  3. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the door control and tire pressure monitoring system receiver assembly if the door control and tire pressure monitoring system receiver assembly has been replaced.
  4. When replacing or inspecting the door control and tire pressure monitoring system receiver assembly and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control and tire pressure monitoring system receiver assembly, wireless function performance may be affected.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the power window regulator master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.CHECK KEY REMINDER WARNING SYSTEM
  1. Check that the key reminder warning buzzer operates normally.

    OK:
    Key reminder warning buzzer operates normally.



NG
GO TO KEY REMINDER WARNING SYSTEM (Click here)
OK


3.CHECK DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY
  1. When a known good registered door control transmitter module set sub-assembly is used, check that the wireless functions operate normally.

    Result:
    Result
    Proceed to
    Wireless door lock/unlock function operates normally with a known good door control transmitter module set sub-assembly.
    A
    Wireless door lock/unlock function does not operate.
    B



B
Go to step 5
A


4.CHECK TRANSMITTER BATTERY (VOLTAGE)
  1. Inspect the transmitter battery capacity.

    1. Remove the transmitter battery from the door control transmitter module set sub-assembly that does not operate (Click here). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



    B281814
  1. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

    NOTICE:
    When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.



    B281815
  1. Check the transmitter battery voltage.

    HINT:
    Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.

    Standard Voltage:
    Item
    Content
    Tester Connection
    Transmitter battery positive (+) - Transmitter battery negative (-)
    Condition
    Ignition switch off, all doors closed and lock or unlock switch is pressed
    Specified Condition
    2.5 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

5.CHECK WAVE ENVIRONMENT
  1. Bring the door control transmitter module set sub-assembly near the door control and tire pressure monitoring system receiver assembly, and perform a wireless operation check.

    HINT:
    1. When the door control transmitter module set sub-assembly is brought near the door control and tire pressure monitoring system receiver assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Wireless functions operate normally.



NG
Go to step 6
OK

END (AFFECTED BY WAVE INTERFERENCE) 

6.SWITCH TO SELF-DIAGNOSTIC MODE (USING TECHSTREAM)
  1. Connect the Techstream to the DLC3

  1. Turn the Ignition switch ON (IG)

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Wireless Diagnosis Mode.

  1. Proceed to the next step in accordance with the prompts on the Techstream screen.



    B220865E09
  1. Check that the system has switched to self-diagnostic mode by checking the room light output pattern.


NEXT


7.CHECK SELF DIAGNOSTIC MODE

B163380E41

  1. Inspect the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the flashing pattern of the interior lights.

    Result:
    Result
    Proceed to
    Normal wave (light flash pattern ) is output.
    A
    Unmatching recognition code is output.
    B
    No diagnostic outputs.
    C



B
Go to step 8

C
Go to step 9
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

8.REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).

    OK:
    Recognition code can be registered.



NG
Go to step 13
OK

END (GO TO OPERATION CHECK) 

9.CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (RESPONSE)
  1. Prepare the door control transmitter module set sub-assembly from another vehicle.

  1. Press and hold down the door control transmitter module set sub-assembly switch.

  1. Check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



NG
Go to step 10
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

10.CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (+B, GND)


    B281166E05
  1. Disconnect the M20 door control and tire pressure monitoring system receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M20-12 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    M20-7 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to door control and tire pressure monitoring system receiver assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (OUTPUT)
  1. Connect the M20 door control and tire pressure monitoring system receiver assembly connector.



    B274835E51
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M20-4 (RDA) - Body ground
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed
    Pulse generation

    Text in Illustration 
    *a
    Component with harness connected
    (door control and tire pressure monitoring system receiver assembly)



NG
REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the G59 main body ECU (multiplex network body ECU) connector and the M20 door control and tire pressure monitoring system receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G59-16 (RDA) - M20-4 (RDA)
    Always
    Below 1 Ω
    G59-16 (RDA) - Body ground
    Always
    10 kΩ or higher
    G59-4 (PRG) - M20-5 (PRG)
    Always
    Below 1 Ω
    G59-4 (PRG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY
  1. Temporarily replace the door control and tire pressure monitoring system receiver assembly with a new or known good one (Click here).


NEXT


14.REGISTER RECOGNITION CODE
  1. Perform the Registration procedure (Click here).


NEXT


15.CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (OPERATION)
  1. Check that the doors can be locked and unlocked by using the door control transmitter module set sub-assembly lock and unlock switches.

    OK:
    Doors can be locked and unlocked using door control transmitter module set sub-assembly.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY WAS DEFECTIVE)