Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL TRANSPONDER KEY ECU ASSEMBLY (w/o Smart Key System)


    B309758
  1. Engage the 2 guides and claw to install the transponder key ECU assembly.



2. INSTALL ID CODE BOX (IMMOBILIZER CODE ECU) (w/ Smart Key System)


    B309758
  1. Engage the 2 guides and claw to install the ID code box (immobiliser code ECU).



3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
  1. Engage the 3 claws to install the No. 2 air duct sub-assembly.

    NOTICE:
    If any of the claws of the No. 2 air duct sub-assembly are cracked or deformed, make sure to replace the air duct with a new one. Failure to do so may cause the No. 2 air duct sub-assembly to fall off or noise to occur.



4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY
  1. Engage the 3 claws to install the No. 3 air duct sub-assembly.

    NOTICE:
    If any of the claws of the No. 3 air duct sub-assembly are cracked or deformed, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.



5. INSTALL AIR CONDITIONING HARNESS ASSEMBLY
  1. Connect each connector.

  1. Engage each clamp to install the air conditioning harness assembly.



6. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY


  1. Temporarily install the air conditioning amplifier assembly as shown in the illustration.


    E238233

  1. Install the air conditioning amplifier assembly with the screw.

  1. Connect the connector.



7. INSTALL ASPIRATOR
  1. Engage the 2 claws and install the aspirator.



8. INSTALL AIR CONDITIONING RADIATOR ASSEMBLY
  1. Install the air conditioning radiator assembly with the 3 screws.

  1. Connect the connector.



9. TEMPORARILY TIGHTEN AIR CONDITIONER UNIT ASSEMBLY
  1. Temporarily tighten the air conditioning unit with the 3 bolts and nut.

    NOTICE:
    To prevent damage to the installation bracket for the air conditioning unit, be sure to support the air conditioning unit in place.



10. CONNECT DRAIN COOLER HOSE


    E238234E01
  1. Install the drain cooler hose as shown in the illustration.
    Text in Illustration 
    *a
    UP Mark
    *b
    90°

    NOTICE:
    1. Install the drain hose with its UP mark facing upward, within the 90 degree range shown in the illustration.
    2. Install the drain hose without twisting it.



11. INSTALL DEFROSTER NOZZLE ASSEMBLY
  1. Engage the 2 claws and 3 guides to install the defroster nozzle assembly.



12. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


  1. Install the instrument panel reinforcement with the 8 bolts.


    E238214E01


    Text in Illustration 
    *1
    Bolt
    *2
    Screw

  1. Temporarily tighten the 3 screws.



13. REMOVE INSTRUMENT PANEL WIRE


  1. Engage each clamp.


    E238213E01


    Text in Illustration 
    *1
    Earth Wire
    -
    -

  1. Connect the connector.

  1. Install the earth wire with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



  1. Engage each clamp.


    E238212E01


    Text in Illustration 
    *1
    Earth Wire
    *2
    Bolt <A>
    *2
    Bolt <B>
    -
    -

  1. Connect the connector.

  1. Install the bolt <B>.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Install the 2 earth wires with the 2 bolts <A>.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    E238211
  1. for RH Side:

    1. Engage each clamp and connect the connector holder.

    2. Install the bolt.

      Torque:
      8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

    3. Connect each connector.



    E238209
  1. for LH Side:

    1. Engage each clamp and connect the connector holder.

    2. Connect the connector to the connector holder.

    3. Install the bolt.

      Torque:
      8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

    4. Connect each connector.



14. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E238207E01
  1. Install the No. 1 instrument panel brace sub-assembly with the 2 bolts, screw and nut.
    Text in Illustration 
    *A
    for Cold Area Specification Vehicles
    *1
    Bolt
    *2
    Screw
    *3
    Nut
    *4
    Earth Wire

    HINT:
    Do not fully tighten the screw.

  1. for Cold Area Specification Vehicles:

    1. Install the earth wire with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage each clamp.



15. INSTALL AIR CONDITIONER UNIT ASSEMBLY


  1. Tighten install the 2 No. 1 air duct bolts.


    E238235E01


    Text in Illustration 
    *1
    No. 1 air duct bolt
    *2
    Bolt
    *3
    Screw
    *4
    Nut

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the bolt, nut and 4 screws in the order shown in the illustration.

    Torque:
    Bolt:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
    Screw (1), (2), (3):
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



16. INSTALL REAR NO. 1 AIR DUCT (for Cold Area Specification Vehicles)
  1. Engage the 2 claws to install the rear No. 1 air duct.



17. INSTALL REAR NO. 2 AIR DUCT (for Cold Area Specification Vehicles)
  1. Engage the 2 claws to install the rear No. 2 air duct.



18. INSTALL REAR NO. 4 AIR DUCT (for Cold Area Specification Vehicles)
  1. Engage the 2 claws to install the rear No. 4 air duct.



19. INSTALL FRONT FLOOR CARPET ASSEMBLY (for Cold Area Specification Vehicles)
  1. Temporarily install the front floor carpet assembly.



    E238237
  1. Insert the front floor carpet and engage the claw.



    E238236
  1. Insert the front floor carpet and engage the claw.



20. INSTALL REAR NO. 3 AIR DUCT (for Cold Area Specification Vehicles)
  1. Engage the 2 claws to install the rear No. 3 air duct.



21. INSTALL JACK ASSEMBLY (for Cold Area Specification Vehicles)
  1. Install the jack assembly.



22. INSTALL JACK COVER (for Cold Area Specification Vehicles)
  1. Engage the 2 claws to install the jack cover.



23. INSTALL FRONT FLOOR CAUTION PLATE COVER (for Cold Area Specification Vehicles)
  1. Engage the guide and claw to install the front floor caution plate cover.



24. CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Cold Area Specification Vehicles)


    E238238
  1. Engage the guide as shown in the illustration.

  1. Install the fuel lid lock open lever sub-assembly with the screw.



25. INSTALL FRONT FLOOR CARPET ASSEMBLY (except Cold Area Specification Vehicles)
  1. Install the front floor carpet assembly.



26. INSTALL NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Key System)
  1. Engage the clamp and Install the No. 2 indoor electrical key antenna assembly.

    NOTICE:
    Be careful when installing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.

  1. Connect the connector.



27. INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Key System)
  1. Engage the clamp to install the No. 1 indoor electrical key antenna assembly.

    NOTICE:
    Be careful when installing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.

  1. Connect the connector.



28. INSTALL VEHICLE APPROACHING SPEAKER CONTROLLER


    E239788
  1. Install the vehicle approaching speaker controller with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



29. INSTALL POWER STEERING ECU ASSEMBLY


    C248049
  1. Install the power steering ECU assembly with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    C248048
  1. Connect the 4 connectors to the power steering ECU assembly.



30. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E240400
  1. Engage the claw to connect the connector as shown in the illustration.

    NOTICE:
    Be sure to engage the connector securely.



    E240398
  1. Engage the claw to lock the connector lock as shown in the illustration.



    E240396
  1. Engage the claw to connect the connector as shown in the illustration.

    NOTICE:
    Be sure to engage the connector securely.

  1. Engage the 2 clamps to connect the wire harness.

  1. Install the instrument panel junction block assembly with the 2 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }



    E245086E01
  1. Connect the connector (A).

  1. Engage the 2 claws to connect the 2 connectors (B) as shown in the illustration.

    NOTICE:
    Be sure to engage each connector securely.

  1. Engage the clamp.



31. CONNECT INSTRUMENT PANEL WIRE
  1. Engage the 2 clamps to connect the instrument panel wire.

  1. Install the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



32. INSTALL POWER MANAGEMENT CONTROL ECU
  1. Install the power management control ECU with the 2 nuts.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Connect the 4 connectors.



33. INSTALL FRONT SEAT ASSEMBLY LH (for Cold Area Specification Vehicles)
w/ Non-removable Headrest: (Click here)
w/ Removable Headrest: (Click here)


34. INSTALL FRONT SEAT ASSEMBLY RH (for Cold Area Specification Vehicles)

HINT:
Use the same procedure as for the LH side.



35. INSTALL STEERING COLUMN ASSEMBLY
(Click here)


36. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


37. CONNECT WATER HOSE SUB-ASSEMBLY


    E240547E01
  1. Connect the water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.
    Text in Illustration 
    *a
    View A
    *b
    Water Hose Sub-assembly Marking (White)
    *c
    Clip installation angle (60° to 150°)

    NOTICE:
    Do not apply excessive force to the water hose sub-assembly.



38. CONNECT HEATER WATER OUTLET HOSE A


    E240548E01
  1. Connect heater water outlet hose A with the marking (purple) facing up and engage the clip within the area shown in the illustration.
    Text in Illustration 
    *a
    View A
    *b
    Heater Water Outlet Hose A (Purple)
    *c
    Clip installation angle (-45° to 45°)

    NOTICE:
    Do not apply excessive force to heater water outlet hose A.



39. CONNECT LIQUID PIPE SUB-ASSEMBLY
  1. Remove the vinyl tape from the liquid pipe sub-assembly.

  1. Sufficiently apply compressor oil to a new O-ring and fitting surface of the liquid pipe sub-assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring to the liquid pipe sub-assembly.

  1. Install the liquid pipe sub-assembly.



40. CONNECT SUCTION PIPE SUB-ASSEMBLY
  1. Remove the vinyl tape from the suction pipe sub-assembly.

  1. Sufficiently apply compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring to the suction pipe sub-assembly.

  1. Connect the suction pipe sub-assembly.



    E240549
  1. Rotate the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



41. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C250015E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the clamp to install the wire harness.



42. INSTALL FRONT NO. 1 VENTILATOR SEAL
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



43. INSTALL FRONT AIR SHUTTER SEAL
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



44. INSTALL INNER COWL TOP TO COWL BRACE


    C250011E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



45. INSTALL WINDSHIELD WIPER MOTOR AND LINK
(Click here)


46. INSPECT FOR COOLANT LEAK (for Engine)

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A268671
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator, engine water pump, front exhaust pipe assembly and engine coolant temperature sensor for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



47. INSPECT ENGINE COOLANT LEVEL IN RESERVOIR (for Engine)
  1. Check that the engine coolant level is between the low and full lines when the engine is cold.
    If the engine coolant level is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the full line.

    NOTICE:
    Do not substitute plain water for engine coolant.



48. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump or appropriate equipment.



  1. Charge the air conditioning system with refrigerant.

    Refrigerant type:
    HFC-134a (R134a)



    E143108E11


    Text in Illustration 
    *a
    Sub-cool System
    *b
    High Pressure
    *c
    Refrigerant Amount
    *d
    Standard charge amount
    *e
    Charge additional 100g (3.5 oz.)
    *f
    Point where bubbles disappear
    *g
    Mean value in proper range
    *h
    Overcharged

    Standard charge amount:
    370 to 470g (13.0 to 16.6oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
    2. The refrigerant amount should be checked by quantity (weight).

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



49. WARM UP COMPRESSOR
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).



50. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Turn the power switch off.
    2. Ensure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).
    3. Repeat the inspection 2 or 3 times.
    4. Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.
      Pressure when the compressor is off: approx. 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi)



    I042222E40
  1. Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Inspect for Leak



    N014519E08
  1. Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *2
    Drain Hose

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. Bring the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.

  1. If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.

  1. Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.

    HINT:
    When checking for leaks, the presence of oily dirt at a joint can indicate a leak.