Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT STEERING COLUMN ASSEMBLY


    C235885
  1. Check that the 2 bushings are securely installed to the steering column assembly.
    If the bushings are deformed, missing or damaged, replace the electric power steering column sub-assembly with a new one.



    C234253E02
  1. Check that the 2 capsules are securely installed to the electric power steering column sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Capsule
    *a
    OK
    *b
    NG

    Standard:
    Capsules do not overlap the corner parts of the brackets.

    NOTICE:
    1. If the standard value is not satisfied, replace the electric power steering column sub-assembly with a new one.
    2. If the capsules have deformation, damage or misalignment, replace the electric power steering column sub-assembly with a new one.



2. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    Bolt:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    Nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. Be sure there is no interference around the wire harness.
    2. There are two different bolt sizes (12 mm (0.472 in.) or 14 mm (0.551 in.)) available.

  1. Engage the wire harness clamp.

  1. Connect the 2 connectors to the power steering ECU assembly.

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.



3. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
(Click here)


4. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY
(Click here)


5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


  1. When reusing the electric power steering column sub-assembly and No. 2 steering intermediate shaft assembly:



      C252587E01
    1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly, and install them.
      Text in Illustration 
      *a
      Matchmark



  1. When replacing the electric power steering column sub-assembly or No. 2 steering intermediate shaft assembly:



      C236078E01
    1. Align the marking (pink) on the steering column assembly shaft with the slit of the No. 2 steering intermediate shaft assembly, and install them.
      Text in Illustration 
      *a
      Marking (Pink)
      *b
      Slit



    C252592E01
  1. Install the bolt while aligning the No. 2 steering intermediate shaft assembly with the position A as shown in the illustration.

    Standard A:
    17.5 to 18.7 mm (0.689 to 0.736 in.)

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



6. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


    C232525E01
  1. Install the steering sliding yoke sub-assembly to the No. 2 steering intermediate shaft assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Align the matchmarks on the steering sliding yoke sub-assembly and the No. 2 steering intermediate shaft assembly.

  1. Temporarily install the bolt.

    HINT:
    Fully tighten the bolt after installing the steering sliding yoke sub-assembly to the steering gear assembly.



7. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY


    C249572E03
  1. Install the steering sliding yoke sub-assembly to the steering gear assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    1. Align the matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.
    2. When the steering sliding yoke sub-assembly is replaced with a new one, it has no matchmarks, so install it while the head of the bolt B faces the back of the vehicle.

  1. Install bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



8. INSTALL COLUMN HOLE COVER SILENCER SHEET


    C248046
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



9. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY
(Click here)


10. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
  1. Do not replace the spiral cable with sensor sub-assembly with the negative (-) auxiliary battery cable connected and the ignition switch on (IG).
  2. Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the negative (-) auxiliary battery cable connected and the ignition switch on (IG).
  3. Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.
  4. Do not remove the spiral cable from the steering sensor.

  1. Using pliers, expand the clamp.

  1. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

  1. Return the clamp to its original position.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.



11. INSTALL UPPER STEERING COLUMN COVER


    C248044
  1. Engage the 2 claws to install the upper steering column cover.



12. INSTALL LOWER STEERING COLUMN COVER


    C256915
  1. Engage the 4 claws to install the lower steering column cover.



    C248042
  1. Install the 3 screws.



13. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


14. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B296308
  1. Rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.



    B296309E01
  1. Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to align the marks.
    Text in Illustration 
    *a
    Alignment Mark

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



15. INSTALL STEERING WHEEL ASSEMBLY


    C252595E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft to install the steering wheel assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



16. INSTALL HORN BUTTON ASSEMBLY
(Click here)


17. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
(Click here)