DTC B1627/82 Lost communication with Side Airbag Sensor LH |
DTC B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete |
DTC B1637/82 Lost Communication with Rear Airbag Sensor LH |
DTC B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete |
DTC B1647/82 Lost Communication with Side Satellite Sensor Bus LH |
DTC B1697/82 Lost Communication with Door Side Airbag Sensor LH |
DTC B1698/82 Door Side Airbag Sensor LH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1627/82 B1628/82 B1637/82 B1638/82 B1647/82 B1697/82 B1698/82 |
|
|

| 1.CHECK CURRENT DTC |
Check for current DTCs (Click here).
| Result | Proceed to |
| Current DTC B1647 or 82 is output. | A |
| Current DTC B1628 or B1638 is output. | B |
| Current DTC B1697 or B1698 is output. | C |
| Current DTC B1627 or B1637 is output. | D |
| Current DTCs B1627, B1628, B1637, B1638, B1647, B1697, B1698 and 82 are not output. | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.
Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - M24-3 (BBL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - M24-3 (BBL-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| M24-3 (BBL-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| M24-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - M24-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
| *b | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 8.CHECK FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - M24-2 (BCL-) | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 9.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| M24-2 (BCL-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 10.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| M24-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 11.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (OPEN) |
![]() |
Connect the connectors that link the floor wire and front door wire LH.
Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - M26-2 (BDL-) | Always | Below 1 Ω |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *3 | Service Wire |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
| *b | Front view of wire harness connector (to Door Side Airbag Sensor LH) |
|
| ||||
| OK | |
| 12.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - M26-2 (BDL-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 13.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| M26-2 (BDL-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 14.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| M26-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 15.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connectors to the side No. 2 airbag sensor assembly LH, door side airbag sensor LH and airbag sensor assembly.
Interchange the side airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1647 or 82 is output. | A |
| DTC B1642 or 81 is output. | B |
| DTCs B1642 or 81 and B1647 or 82 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | |
| 16.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH |
![]() |
Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1647 or 82 is output. | A |
| DTC B1642 or 81 is output. | B |
| DTCs B1642 or 81 and B1647 or 82 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly LH |
|
| ||||
|
| ||||
| A | |
| 17.CHECK DOOR SIDE AIRBAG SENSOR LH |
![]() |
Interchange the door side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1647 or 82 is output. | A |
| DTC B1642 or 81 is output. | B |
| DTCs B1642 or 81 and B1647 or 82 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors.
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
|
| ||||
|
| ||||
| A | ||
| ||
| 18.CHECK HISTORY DTC |
Check for history DTCs (Click here).
| Result | Proceed to |
| History DTCs B1627 and B1637 are not output. | A |
| History DTC B1627 is output. | B |
| History DTC B1637 is output. | C |
|
| ||||
|
| ||||
| A | |
| 19.CHECK CURRENT DTC |
Check for current DTCs (Click here).
| Result | Proceed to |
| Current DTC B1628 is output. | A |
| Current DTC B1638 is output. | B |
|
| ||||
| A | |
| 20.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly LH.
Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 21.CHECK FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - M24-3 (BBL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 22.CHECK FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - M24-3 (BBL-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 23.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| M24-3 (BBL-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 24.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| M24-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 25.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connector to the airbag sensor assembly.
Interchange the side airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1628 is output. | A |
| DTC B1623 is output. | B |
| DTCs B1623 and B1628 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | ||
| ||
| 26.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.
Disconnect the connectors from the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 27.CHECK FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - M24-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
| *b | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 28.CHECK FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - M24-2 (BCL-) | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 29.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| M24-2 (BCL-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 30.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M24-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| M24-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 31.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connector to the side No. 2 airbag sensor assembly LH.
Interchange the side airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1638 is output. | A |
| DTC B1633 is output. | B |
| DTCs B1633 and B1638 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | |
| 32.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH |
![]() |
Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1638 is output. | A |
| DTC B1633 is output. | B |
| DTCs B1633 and B1638 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly LH |
|
| ||||
|
| ||||
| A | ||
| ||
| 33.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.
Disconnect the connectors from the side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 34.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (OPEN) |
![]() |
Connect the connectors that link the floor wire and front door wire LH.
Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - M26-2 (BDL-) | Always | Below 1 Ω |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *3 | Service Wire |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
| *b | Front view of wire harness connector (to Door Side Airbag Sensor LH) |
|
| ||||
| OK | |
| 35.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - M26-2 (BDL-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 36.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| M26-2 (BDL-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 37.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M26-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| M26-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 38.CHECK DOOR SIDE AIRBAG SENSOR LH |
![]() |
Connect the connectors to the side No. 2 airbag sensor assembly LH.
Interchange the door side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1697 or B1698 is output. | A |
| DTC B1692 or B1693 is output. | B |
| DTCs B1692, B1693, B1697 and B1698 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors.
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
|
| ||||
|
| ||||
| A | |
| 39.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH |
![]() |
Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1697 or B1698 is output. | A |
| DTC B1692 or B1693 is output. | B |
| DTCs B1692, B1693, B1697 and B1698 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly LH |
|
| ||||
|
| ||||
| A | ||
| ||
| 40.CHECK CURRENT DTC |
Check for current DTCs (Click here).
| Result | Proceed to |
| Current DTC B1627 is output. | A |
| Current DTC B1637 is output. | B |
Turn the ignition switch off.
|
| ||||
| A | |
| 41.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Interchange the side airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1627 is output. | A |
| DTC B1622 is output. | B |
| DTCs B1622 and B1627 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | ||
| ||
| 42.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH |
![]() |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1637 is output. | A |
| DTC B1632 is output. | B |
| DTCs B1632 and B1637 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly LH |
|
| ||||
|
| ||||
| A | ||
| ||
| 43.CHECK FRONT DOOR WIRE LH (OPEN) |
![]() |
Disconnect the front door wire LH connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JM1-1 (BDL+) - JM1-2 (BDL-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector (to Floor Wire) |
| *b | Front view of wire harness connector (to Door Side Airbag Sensor LH) |
|
| ||||
| OK | ||
| ||
| 44.CHECK FRONT DOOR WIRE LH (SHORT) |
![]() |
Disconnect the front door wire LH connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JM1-1 (BDL+) - JM1-2 (BDL-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||
| 45.CHECK FRONT DOOR WIRE LH (SHORT TO B+) |
![]() |
Disconnect the front door wire LH connector from the floor wire.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JM1-1 (BDL+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| JM1-2 (BDL-) - Body ground | Ignition switch ON (IG) | Below 1 V |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||
| 46.CHECK FRONT DOOR WIRE LH (SHORT TO GROUND) |
![]() |
Disconnect the front door wire LH connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JM1-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| JM1-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||