DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2237 | An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic). |
|
| P2238 |
|
|
| P2239 | The A1A+ voltage is higher than 4.5 V (2 trip detection logic). |
|
| P2252 | The A1A- voltage is 0.5 V or less (2 trip detection logic). |
|
| P2253 | The A1A- voltage is higher than 4.5 V (2 trip detection logic). |
|
| Related DTCs | P2237: Air fuel ratio sensor open circuit between A1A+ and A1A- P2238: Air fuel ratio sensor short circuit between A1A+ and A1A- P2238: Air fuel ratio sensor short circuit between A1A+ and GND P2238: Air fuel ratio sensor low admittance P2239: Air fuel ratio sensor short circuit between A1A+ and +B P2252: Air fuel ratio sensor short circuit between A1A- and GND P2253: Air fuel ratio sensor short circuit between A1A- and +B |
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Engine coolant temperature sensor Crank position sensor |
| Frequency of Operation | Continuous |
| Duration | 10 seconds: P2237 10 seconds: P2238 (air fuel ratio sensor low admittance) 5 seconds: Others |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0016 (VVT system - misalignment) P0031, P0032, P101D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0107, P0108 (Manifold absolute pressure) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172 (Fuel system) P0301, P0302, P0303, P0304 (Misfire) P0335 (Crankshaft position sensor) P0401 (EGR system (closed)) P0451, P0452, P0453 (EVAP system) P0505 (Idle speed control) P219A, P219C, P219D, P219E, P219F (Air fuel ratio imbalance) |
| Monitor runs whenever the following DTCs are not stored | None |
| Estimated sensor temperature | 450 to 550°C (842 to 1022°F) |
| Engine | Running |
| Auxiliary battery voltage | 11 V or higher |
| Ignition switch | ON (IG) |
| Time after ignition switch is turned from off to ON (IG) | 5 seconds or more |
| Estimated sensor temperature | 700 to 800°C (1292 to 1472°F) |
| Engine coolant temperature | 5°C (41°F) or higher |
| Fuel cut | Not executed |
| Auxiliary battery voltage | 11 V or higher |
| Ignition switch | ON (IG) |
| Time after ignition switch is turned from off to ON (IG) | 5 seconds or more |
| Auxiliary battery voltage | 11 V or higher |
| Ignition switch | ON (IG) |
| Time after ignition switch is turned from off to ON (IG) | 5 seconds or more |
| Auxiliary battery voltage | 11 V or higher |
| Ignition switch | ON (IG) |
| Time after ignition switch is turned from off to ON (IG) | 5 seconds or more |
| Auxiliary battery voltage | 11 V or higher |
| Ignition switch | ON (IG) |
| Time after ignition switch is turned from off to ON (IG) | 5 seconds or more |
| Auxiliary battery voltage | 11 V or higher |
| Ignition switch | ON (IG) |
| Time after ignition switch is turned from off to ON (IG) | 5 seconds or more |
| Air fuel ratio sensor admittance | Less than 0.002 1/Ω |
| Air fuel ratio sensor admittance | Less than 0.0074 1/Ω |
| A1A+ terminal voltage | 0.5 V or less |
| Difference between A1A+ terminal and A1A- terminal voltage | 0.1 V or less |
| A1A+ terminal voltage | Higher than 4.5 V |
| A1A- terminal voltage | 0.5 V or less |
| A1A- terminal voltage | Higher than 4.5 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C17-1 (HA1A) - C10-23 (HA1A) | Always | Below 1 Ω |
| C17-3 (A1A+) - C10-133 (A1A+) | Always | Below 1 Ω |
| C17-4 (A1A-) - C10-134 (A1A-) | Always | Below 1 Ω |
| C17-1 (HA1A) or C10-23 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C17-3 (A1A+) or C10-133 (A1A+) - Body ground | Always | 10 kΩ or higher |
| C17-4 (A1A-) or C10-134 (A1A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2237, P2238, P2239, P2252 or P2253.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2237, P2238, P2239, P2252 or P2253 is output) | B |
|
| ||||
| A | ||
| ||