Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A85-123    Hybrid Battery Pack Cooling Fan 1 Control Circuit High

for Preparation Click here


DESCRIPTION

Refer to the circuit description for DTC P0A84-123 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A85
123
Both of the following conditions are met due to the battery cooling blower system malfunction:
(1 trip detection logic)
  1. The speed calculated based on the battery cooling blower assembly output frequency (FP) is not within the target control speed range.
  2. The battery cooling blower assembly speed is excessively high when a speed below a certain level is requested.
  1. Battery cooling blower assembly
  2. Battery smart unit

Related Data List 
DTC No.
Data List
P0A85-123
  1. Cooling Fan 0
  2. Cooling Fan Mode 1
  3. Cooling Fan Frequency 1
The following items can be helpful when performing repairs:
Data List
  1. Temp of Batt TB1 to 3
  2. +B

HINT:
  1. "Cooling Fan Frequency 1" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly rotation speed.
  2. If the battery cooling blower assembly speed is too high, this DTC is stored.


WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

  3. When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
  1. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
    4. Select fan mode 6 and operate the battery cooling blower assembly.
  2. Operation of the battery cooling blower can be confirmed by checking if air is sucked into the air intake port of the intake duct.

1.CHECK FOR DTCS (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.CHECK BATTERY SMART UNIT (FREQUENCY)
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the ignition switch to ON (READY) unless instructed by the repair manual because this may cause a malfunction.
    2. If the ignition switch is turned to on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the Techstream (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.

    NOTICE:
    When DTCs are cleared, freeze frame data and INF codes are also cleared.

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / All Data / Cooling Fan Frequency 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.



    A266555E03
  1. While the cooling fan is operating, compare the value in the data list (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    M41-2 (FP0) - M41-4 (GND0)
    Battery cooling blower is operating

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

    Result:
    Result
    Proceed to
    The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are 0 Hz.
    A
    The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are not 0 Hz.
    B

    NOTICE:
    Turning the ignition switch to ON (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the rear seat cushion leg sub-assembly.



B
Go to step 4
A


3.CHECK BATTERY SMART UNIT
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Disconnect connector M39 from the battery smart unit.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the ignition switch to ON (READY) unless instructed by the repair manual because this may cause a malfunction.
    2. If the ignition switch is turned to on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the Techstream (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.

    NOTICE:
    When DTCs are cleared, freeze frame data and INF codes are also cleared.

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / All Data / Cooling Fan Frequency 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.



    A318993E01
  1. While the cooling fan is operating, measure the frequency on the wire harness side of the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    M39-5 (FP0) - Body ground
    Battery cooling blower is operating

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Smart Unit)

    Result:
    Result
    Proceed to
    The actual measured value at the battery cooling blower assembly connector remains 0 Hz.
    A
    The actual measured value at the battery cooling blower assembly connector is not 0 Hz.
    B

    NOTICE:
    Turning the ignition switch to ON (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the battery cooling blower assembly connector.

  1. Install the rear seat cushion leg sub-assembly.



B
REPLACE BATTERY SMART UNIT (Click here)
A

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)  

4.CHECK BATTERY SMART UNIT
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the ignition switch to ON (READY) unless instructed by the repair manual because this may cause a malfunction.
    2. If the ignition switch is turned to on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the Techstream (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.

    NOTICE:
    When DTCs are cleared, freeze frame data and INF codes are also cleared.

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / All Data / Cooling Fan Frequency 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.



    A266555E03
  1. While the cooling fan is operating, compare the value in the data list (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    M41-2 (FP0) - M41-4 (GND0)
    Battery cooling blower is operating

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

    Result:
    Result
    Proceed to
    Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector is 10% or less.
    A
    Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector is more than 10%.
    B

    NOTICE:
    Turning the ignition switch to ON (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the rear seat cushion leg sub-assembly.



B
REPLACE BATTERY SMART UNIT (Click here)
A

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)