METER / GAUGE SYSTEM > Speed Signal Circuit |

| 1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE) |
![]() |
Disconnect the G1 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G1-39 (+S) - Body ground | Power switch on (IG) | 4.5 to 14 V |
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
|
| ||||
| OK | |
| 2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) |
Reconnect the G1 combination meter assembly connector.
![]() |
Disconnect the A41 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-11 (SP1) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU) |
|
| ||||
| OK | |
| 3.INSPECT SKID CONTROL ECU (INPUT WAVEFORM) |
![]() |
Check the input waveform.
Reconnect the A41 skid control ECU connector.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal G1-40 (SI) and body ground.
Turn the power switch on (IG).
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Wheel being rotated |
| *a | Component with harness connected (Combination Meter Assembly) |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU) |
Disconnect the G1 combination meter assembly connector.
Disconnect the A41 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-11 (SP1) - G1-40 (SI) | Always | Below 1 Ω |
| A41-11 (SP1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR) |
Disconnect the 3B junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G1-39 (+S) - 3B-15 | Always | Below 1 Ω |
| G1-39 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR) |
Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.
Disconnect the 3A junction connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3A-16 - Body ground | Power switch on (IG) | 4.5 to 14 V |
| 3A-37 - Body ground | Power switch on (IG) | 4.5 to 14 V |
| 3A-38 - Body ground | Power switch on (IG) | 4.5 to 14 V |
| Result | Proceed to |
| Voltage is not present in one circuit. | A |
| Voltage is present in all the circuits. | B |
|
| ||||
| A | |
| 7.SYSTEM CHECK |
Select the circuit for which voltage was not present in step 6.
| Tester Connection | System that uses the circuit | Proceed to |
| 3A-16 - Body ground | Audio/Visual system*1, *2 | A |
| 3A-37 - Body ground | Hybrid control system | B |
| 3A-38 - Body ground | Vehicle proximity notification system | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT, RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT) |
Disconnect the G41 radio receiver assembly*1 or G78 radio and display receiver assembly*2
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G41-17 (SPD)*1 - Body ground | Always | 10 kΩ or higher |
| G78-17 (SPD)*2 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK (for Radio Receiver Type) | A |
| OK (for Radio and Display Type) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU ASSEMBLY CIRCUIT) |
Disconnect the G57 power management control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G57-14 (SPDI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER CIRCUIT) |
Disconnect the G82 vehicle approaching speaker controller connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G82-6 (SPD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||