Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER

BRAKE BOOSTER > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE BOOSTER GASKET
  1. Install a new brake booster gasket to the brake booster with master cylinder assembly.



2. INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


    C250004E01
  1. Install the brake booster with master cylinder assembly with the 4 nuts.
    Text in Illustration 
    *1
    Connector Portion
    *2
    Union
    *3
    Push Rod Clevis
    *4
    Boot
    *5
    Front No. 2 Brake Tube

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.
    3. Be careful not to allow brake fluid to enter the connector.
    4. If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.



    C250028E01
  1. Temporarily tighten each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.
    Text in Illustration 
    *a
    to Front Wheel Cylinder LH
    *b
    to Rear Wheel Cylinder RH
    *c
    to Brake Booster Pump Assembly
    *d
    to Rear Wheel Cylinder LH
    *e
    to Front Wheel Cylinder RH

  1. Using a union nut wrench, fully tighten each brake line.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



    C250027
  1. Connect the connector to the brake booster with master cylinder assembly.
    Text in Illustration 
    V100135
    Connect the connector
    V100136
    Lock the lock lever

    NOTICE:
    1. Make sure that the connector can be connected smoothly. Do not allow foreign matter to enter.
    2. Make sure that the connector lock is locked securely.



3. INSTALL TUBE CLAMP BRACKET


    C250025E01
  1. Temporarily install the tube clamp bracket to the brake booster with master cylinder assembly with the front No. 1 brake tube and 2 bolts.
    Text in Illustration 
    *1
    Front No. 1 Brake Tube
    *a
    The tube clamp bracket contacts the brake booster with master cylinder assembly.

  1. Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    Bolt (1):
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    Bolt (2):
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    When tightening the bolt (1), be sure that the tube clamp bracket contacts the brake booster with master cylinder assembly.



4. CONNECT BRAKE ACTUATOR HOSE


    C250023E01
  1. Connect the brake actuator hose to the brake master cylinder reservoir assembly with the clip.
    Text in Illustration 
    V100136
    Front of Vehicle

    NOTICE:
    1. Make sure that the identification mark on the brake actuator hose is positioned within 30° of the brake master cylinder reservoir assembly rib.
    2. Make sure to install the hose to the proper location.
    3. Install the clip within the range shown in the illustration.



5. INSTALL RESERVOIR BRACKET
  1. Install the reservoir bracket with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. CONNECT NO. 1 RESERVOIR HOSE


    C250020E01
  1. Connect the No. 1 reservoir hose to the brake booster with master cylinder assembly with the clip.
    Text in Illustration 
    V100136
    Up

    NOTICE:
    1. Make sure that the identification mark on the No. 1 reservoir hose is positioned within 30° of the brake booster with master cylinder assembly rib.
    2. When connecting the reservoir hose, face the identification mark up.
    3. Make sure to install the hose to the proper location.
    4. Install the clip within the range shown in the illustration.



7. CONNECT NO. 2 RESERVOIR HOSE


    C250018E01
  1. Connect the No. 2 reservoir hose to the brake booster with master cylinder assembly with the clip.
    Text in Illustration 
    V100136
    Up

    NOTICE:
    1. Make sure that the identification mark on the No. 2 reservoir hose is positioned within 30° of the brake booster with master cylinder assembly rib.
    2. When connecting the reservoir hose, face the identification mark up.
    3. Make sure to install the hose to the proper location.
    4. Install the clip within the range shown in the illustration.



8. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
  1. Install the brake master cylinder reservoir assembly with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



9. INSTALL PUSH ROD PIN


    C251272
  1. Apply lithium soap base glycol grease to the push rod pin and installation hole of the brake pedal sub-assembly.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease

  1. Install the push rod pin and a new clip to connect the push rod clevis to the brake pedal support assembly.

    NOTICE:
    Insert the push rod pin in the correct direction.



10. INSTALL BRAKE PEDAL RETURN SPRING
  1. Install the brake pedal return spring to the brake pedal support assembly and push rod pin.



11. FILL RESERVOIR WITH BRAKE FLUID


12. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL



13. BLEED BRAKE SYSTEM
  1. Remove the outer cowl top panel sub-assembly .



  1. Bleed the brake system.



      C256182
    1. Wait at least 2 minutes with the ignition switch off, and disconnect the reservoir level switch connector.

      NOTICE:
      Do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

      HINT:
      This procedure is not required if the reservoir level switch connector has been disconnected.



    2. C256183
    3. Remove the brake master cylinder reservoir filler cap assembly.

    4. Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    5. Connect the Techstream to the DLC3 and turn the ignition switch to ON (IG).

    6. Turn the Techstream on and enter the following menus: Chassis / ABS/VSC/TRAC / Air Bleeding.

    7. Select "ABS actuator has been replaced" on the Techstream display, and bleed air from the brake fluid following the instructions on the Techstream.

      NOTICE:
      Before following the instructions on the Techstream to perform linear valve offset calibration, release the parking brake. When calibration is complete, immediately apply the parking brake.



    8. C249825E01
    9. After air bleeding, tighten each bleeder plug.

      Torque:
      front bleeder plug:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      rear bleeder plug:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
      stroke simulator bleeder plug:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      HINT:
      The stroke simulator bleeder plug is positioned as shown in the illustration.

      Text in Illustration 
      *1
      Stroke Simulator Bleeder Plug

    10. Clear the DTCs (Click here).

    11. Turn the Techstream off and turn the ignition switch off.

    12. Install the brake master cylinder reservoir filler cap.

  1. Inspect for brake fluid leaks.

  1. Install the outer cowl top panel sub-assembly .



14. INSPECT AND ADJUST BRAKE PEDAL
(Click here)


15. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

HINT:
After the brake booster with master cylinder assembly is replaced, obtain the zero point of the yaw rate and acceleration sensor (Click here).



16. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C250015E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the clamp to install the wire harness.



17. INSTALL FRONT NO. 1 VENTILATOR SEAL
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



18. INSTALL FRONT AIR SHUTTER SEAL
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



19. INSTALL INNER COWL TOP TO COWL BRACE


    C250011E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



20. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY