Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

The temperature can be adjusted and the air inlet can be switched between fresh air mode and recirculated mode by operating switches on the steering pad switch RH. The air conditioning panel (heater control switch board) receives operation signals from the steering pad switch RH via the spiral with sensor cable sub-assembly and sends temperature setting and air inlet change signals to the air conditioning amplifier assembly.

WIRING DIAGRAM


E245293E05


INSPECTION PROCEDURE

1.CHECK AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD)
  1. Disconnect the G5 spiral with sensor cable sub-assembly connector.



    E192242E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G5-10 (AC1) - Body ground
    Ignition switch off
    Below 1 V
    G5-10 (AC1) - Body ground
    Ignition switch ON (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)



NG
Go to step 5
OK


2.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
  1. Disconnect the steering pad switch RH and spiral with sensor cable sub-assembly connectors.



    E220247E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - G5-4 (EAU)
    Center
    Below 3 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-3 (AC1) - G5-10 (AC1)
    Center
    Below 3 Ω
    2.5 rotations to the left
    2.5 rotations to the right

  1. After setting the spiral with sensor cable sub-assembly to the center position, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral with sensor cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - G5-4 (EAU)
    Always
    Below 3 Ω
    z2-3 (AC1) - G5-10 (AC1)
    Always
    Below 3 Ω

    NOTICE:
    1. The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
    2. As the spiral with sensor cable sub-assembly may break, do not rotate the spiral with sensor cable sub-assembly more than the specified amount.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)
    Text in Illustration 
    *a
    Component without harness connected
    (Spiral with Sensor Cable Sub-assembly)



NG
REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (Click here)
OK


3.INSPECT STEERING PAD SWITCH RH
  1. Remove the steering pad switch RH (Click here).



  1. Measure the resistance according to the value(s) in the table below.


    E250525E04


    Text in Illustration 
    *1
    TEMP + Switch
    *2
    TEMP - Switch
    *3
    R/F Switch
    -
    -
    *a
    Component without harness connected
    (Steering Pad Switch RH)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-3 (AC1) - z2-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z2-3 (AC1) - z2-8 (EAU)
    R/F switch pushed
    323 to 335 Ω
    z2-3 (AC1) - z2-8 (EAU)
    TEMP + switch pushed
    980 to 1020 Ω
    z2-3 (AC1) - z2-8 (EAU)
    TEMP - switch pushed
    3048 to 3172 Ω



NG
REPLACE STEERING PAD SWITCH RH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G5-4 (EAU) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G5-10 (AC1) - G33-3 (SWO)
    Always
    Below 1 Ω
    G5-10 (AC1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) (Click here)