Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    U0100-530    Lost Communication with ECM / PCM "A"

DTC    U0129-527    Lost Communication with Brake System Control Module

DTC    U0129-528    Lost Communication with Brake System Control Module

DTC    U0140-146    Communication Error from Body ECU to HV ECU

DTC    U0151-763    Communication Error from Airbag ECU to HV ECU

DTC    U0164-827    Communication Error from A/C ECU to HV ECU

DTC    U1107-436    Lost Communication with Power Management Module

for Preparation Click here


DESCRIPTION

  1. The power management control ECU transmits and receives signals via CAN communication to and from the ECM, skid control ECU assembly, main body ECU, airbag sensor assembly, and air conditioning amplifier assembly.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
U0100
530
Problem with CAN communication between the ECM and power management control ECU (CAN communication system malfunction)
(1 trip detection logic)
CAN communication system
U0129
527
Problem with CAN communication (V BUS) between the skid control ECU assembly and power management control ECU (CAN communication system malfunction)
(1 trip detection logic)
528
Problem with CAN communication between the skid control ECU assembly and power management control ECU (CAN communication system malfunction)
(1 trip detection logic)
U0140
146
Problem with CAN communication between the main body ECU and power management control ECU (CAN communication system malfunction)
(1 trip detection logic)
U0151
763
Problem with CAN communication between airbag sensor assembly and power management control ECU (CAN communication system malfunction)
(1 trip detection logic)
U0164
827
Problem with CAN communication between air conditioning amplifier assembly and power management control ECU (CAN communication system malfunction)
(1 trip detection logic)
U1107
436
Problem with CAN communication between the power source ECU and power management control ECU (CAN communication system malfunction)
(1 trip detection logic)

MONITOR DESCRIPTION

If the power management control ECU detect problem with CAN communication with the ECU, it will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
U0100 (INF 211/212/530): Verify communication
Required sensors / components
Main: Power management control ECU
Sub: CAN bus line
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU
DTC U0100 (INF 211/212/530) is not detected

CONFIRMATION DRIVING PATTERN


A308312E02

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Turn the ignition switch to ON (READY) and wait for 2 minutes or more. [A]
  7. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [B]
  8. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output, perform the following procedure.

  9. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  10. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (IG) and wait for 2 minutes or more.

1.CHECK DTC OUTPUT (HEALTH CHECK)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: System Select / Health Check.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Power management control ECU outputs P2532-772
    A
    Power management control ECU does not output P2532-772
    B

  1. Turn the ignition switch off.



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A

GO TO DTC CHART (P2532-772) (Click here)