POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder |

| 1.CHECK DOOR LOCK OPERATION |
Check door lock operation (Click here).
| Result | Proceed to |
| All doors cannot be locked through multiplex network master switch | A |
| All doors cannot be locked through driver door key cylinder | B |
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (LIN COMMUNICATION SYSTEM) |
Clear the DTC (Click here).
Recheck for DTCs.
|
| ||||
| OK | |
| 3.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Replace the multiplex network master switch assembly (Click here).
| NEXT | |
| 4.CHECK DOOR LOCK OPERATION |
Check that all doors can be locked and unlocked by using the multiplex network master switch (Click here).
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY LINKED LOCK AND UNLOCK SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Door Key SW-Lock | Driver door key-linked lock/unlock switch lock signal/ON or OFF | ON: Driver door key cylinder turned to lock position OFF: Driver door key cylinder not turned to lock position | - |
| Door Key SW-Unlock | Driver door key-linked lock/unlock switch unlock signal/ON or OFF | ON: Driver door key cylinder turned to unlock position OFF: Driver door key cylinder not turned to unlock position | - |
|
| ||||
| OK | ||
| ||
| 6.INSPECT FRONT DOOR LOCK ASSEMBLY (for DRIVER SIDE) (DOOR KEY LINKED LOCK AND UNLOCK SWITCH) |
Remove the front door lock assembly (for driver side) (Click here).
for LHD
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 9 (L) - 7 (E) | Locked | Below 1 Ω |
| 9 (L) - 7 (E) | off | 10 kΩ or higher |
| 10 (UL) - 7 (E) | Unlocked | Below 1 Ω |
| 10 (UL) - 7 (E) | off | 10 kΩ or higher |
| *1 | Component without harness connected (Front Door Lock Assembly LH) |
| *2 | Lock |
| *3 | off |
| *4 | Unlock |
for RHD (w/o Double Locking System)
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 6 (L) - 8 (E) | Locked | Below 1 Ω |
| 6 (L) - 8 (E) | off | 10 kΩ or higher |
| 5 (UL) - 8 (E) | Unlocked | Below 1 Ω |
| 5 (UL) - 8 (E) | off | 10 kΩ or higher |
| *1 | Component without harness connected (Front Door Lock Assembly RH) |
| *2 | Lock |
| *3 | off |
| *4 | Unlock |
for RHD (w/ Double Locking System)
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 6 (L) - 8 (E) | Locked | Below 1 Ω |
| 6 (L) - 8 (E) | off | 10 kΩ or higher |
| 5 (UL) - 8 (E) | Unlocked | Below 1 Ω |
| 5 (UL) - 8 (E) | off | 10 kΩ or higher |
| *1 | Component without harness connected (Front Door Lock Assembly RH) |
| *2 | Lock |
| *3 | off |
| *4 | Unlock |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK - MAIN BODY ECU) |
![]() |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O8-9 (L) - L7-11 (L2) | Always | Below 1 Ω |
| O8-10 (UL) - L7-12 (UL2) | Always | Below 1 Ω |
| O8-7 (E) - Body ground | Always | Below 1 Ω |
| L7-11 (L2) - Body ground | Always | 10 kΩ or higher |
| L7-12 (UL2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| N8-6 (L) - L7-11 (L2) | Always | Below 1 Ω |
| N8-5 (UL) - L7-12 (UL2) | Always | Below 1 Ω |
| N8-8 (E) - Body ground | Always | Below 1 Ω |
| L7-11 (L2) - Body ground | Always | 10 kΩ or higher |
| L7-12 (UL2) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Front Door Lock Assembly (for Driver Side)) |
| *2 | Front view of wire harness connector (to Main Body ECU (Multiplex Network Body ECU)) |
| *3 | for LHD |
| *4 | for RHD |
|
| ||||
| OK | ||
| ||