Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P2A00    A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. Refer to DTC P2195 .
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.


DTC No.
DTC Detection Condition
Trouble Area
P2A00
Calculated value for air fuel ratio sensor response rate deterioration level is less than threshold (2 trip detection logic)
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. EGR valve assembly
  4. ECM

CONFIRMATION DRIVING PATTERN

HINT:
This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

Performing this confirmation pattern will activate the air fuel ratio sensor response monitor.

A201252E23

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on ((IG).
  3. Turn the tester on.
  4. Clear the DTCs (Click here).
  5. Turn the power switch off.
  6. Turn the power switch on (IG) and turn the tester on.
  7. Put the engine in inspection mode (Click here).
  8. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].
  9. Drive the vehicle at a constant speed of between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].
  10. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
  11. Check if any DTCs (any pending DTCs) are set [C].

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG) and turn the tester on.
  3. Put the engine in inspection mode (Click here).
  4. Start the engine.
  5. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  7. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  8. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  1. Each sensor reacts in accordance with increases in the fuel injection volume.


Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1
(Air fuel ratio)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5%
Lean
More than 3.4 V
O2S B1S2
(Heated oxygen)
+25%
Rich
More than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A162605E12
A162598E12
-
2
A162596E06
A162598E12
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162605E12
A162596E07
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
  4. Exhaust gas leaks
4
A162596E06
A162596E06
  1. Fuel pressure
  2. Exhaust gas leaks
    (Air fuel ratio extremely lean or rich)
  1. Performing Control the Injection Volume for A/F Sensor enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2.

HINT:
  1. DTC P2A00 may also be set when the air fuel ratio remains rich or lean.
  2. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P2A00 is output
    A
    DTC P2A00 and other DTCs are output
    B

    HINT:
    If any DTCs other than P2A00 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT AIR FUEL RATIO SENSOR NO.2 (HEATER RESISTANCE)


    A170689E11
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (to Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR NO.2 (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)


  1. Disconnect the air fuel ratio sensor connector.


    A217281E03

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D24-1 (HA1A) - D28-18 (HA1A)
    Always
    Below 1 Ω
    D24-3 (A1A+) - D28-103 (A1A+)
    D24-4 (A1A-) - D28-126 (A1A-)


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D24-1 (HA1A) or D28-18 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D24-3 (A1A+) or D28-103 (A1A+) - Body ground
    D24-4 (A1A-) or D28-126 (A1A-) - Body ground


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


4.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs.

  1. Put the engine in inspection mode (Click here).

  1. Drive the vehicle referring to the Confirmation Driving Pattern.


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read the Pending DTCs.

    Result:
    Result
    Proceed to
    DTC P2A00 is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


6.REPLACE AIR FUEL RATIO SENSOR NO.2
  1. Replace the air fuel ratio sensor (Click here).


NEXT


7.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs.

  1. Put the engine in inspection mode (Click here).

  1. Drive the vehicle referring the Confirmation Driving Pattern.


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read the Pending DTCs.

    Result:
    Result
    Proceed to
    DTC P2A00 is output
    A
    DTC is not output
    B



B
END
A


9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling
    MAP
    (Data List)
    MAP value is 20 to 40 kPa (150 to 300 mmHg)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.

    Result:
    Result
    Proceed to
    Outside of standard range
    A
    Within standard range
    B



B
Go to step 11
A


10.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

  1. Reinstall the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


11.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTC (Click here).

  1. Turn the power switch off and wait for 30 seconds.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2A00.

  1. Check the DTC judgment result.


NEXT

END