DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 | Calculated value for air fuel ratio sensor response rate deterioration level is less than threshold (2 trip detection logic) |
|

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P2A00 is output | A |
| DTC P2A00 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Less than 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Less than 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean/Rich | Lean/Rich | Normal | A |
| Lean | Lean | Actual air fuel ratio lean | B |
| Rich | Rich | Actual air fuel ratio rich | B |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | C |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2A00 is output) | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 5.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 6.CHECK FUEL PRESSURE |
Check fuel pressure .
|
| ||||
| OK | |
| 7.INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assembly (Click here).
|
| ||||
| OK | |
| 8.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2A00 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 10.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check the DTC judgment result is NORMAL.
| NEXT | ||
| ||
| 12.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | ||
| ||