DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
|
|
| While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current is 2.2 mA or more for 3 seconds (2 trip detection logic) |
| |
| P2196 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
|
|
| While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic) |
|


| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P2195 or P2196 is output | A |
| DTC P2195 or P2196 and P0136, P0137 or P0138 are output | A |
| DTC P2195 or P2196 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195 or P2196 is output) | B |
|
| ||||
| A | ||
| ||
| 4.READ VALUE USING INTELLIGENT TESTER (AFS CURRENT B1S1) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Put the engine in inspection mode (maintenance mode) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.
Check the value of the air fuel ratio sensor output current during fuel-cut, referring to the Drive Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.
| Test Value | Proceed to |
| Within normal range (0.7 mA or higher, and below 2.2 mA) | A |
| Outside normal range (below 0.7 mA, or 2.2 mA or higher) | B |
|
| ||||
| A | |
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Warm up the engine and run the engine at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Less than 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Less than 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Lean/Rich | Lean/Rich | Normal | B |
|
| ||||
| A | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 7.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 8.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 9.INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assembly (whether fuel volume is high or low, and whether injector pattern is poor) (Click here).
|
| ||||
| OK | |
| 10.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2195 or P2196 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 12.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment result.
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195 or P2196 is output) | B |
|
| ||||
| A | ||
| ||
| 16.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||