DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |

| *1 | Camshaft Position Sensor |
| *2 | Crankshaft Position Sensor |
| *3 | ECM |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | When one of following conditions below is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 | When one of following conditions below is detected (2 trip detection logic):
|

| Engine Speed | Duration |
| Idling | 4 minutes or more |
| 1000 | 4 minutes and 30 seconds or more |
| 2000 | 2 minutes and 30 seconds or more |
| 3000 | 1 minute and 30 seconds or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE (HOSE CONNECTIONS) |
Check the PCV hose connections.
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (CYLINDER #1 MISFIRE COUNT, #2, #3 AND #4) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 (to #4) Misfire Count.
Read each value for Cylinder #1 (to #4) Misfire Count displayed on the intelligent tester. If no misfire counts occur in any cylinders, perform steps [A] and [B], and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the read value using the intelligent tester (Misfire RPM and Misfire Load) procedures above [A].
Read Cylinder #1 (to #4) Misfire Count or the DTCs displayed on the tester [B].
| Misfire Count | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 5.INSPECT SPARK PLUG |
Remove the ignition coil assembly and the spark plug of the misfiring cylinder.
Check the electrode for carbon deposits.
| Manufacturer | Product |
| DENSO | SC20HR11 |
![]() |
Measure the spark plug electrode gap.
Reinstall the ignition coil assembly and spark plug.
|
| ||||
| OK | |
| 6.CHECK FOR SPARK (SPARK TEST) |
Perform spark test .
|
| ||||
| OK | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D14-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| D15-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| D16-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| D17-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to Fuel Injector Assembly) |
Reconnect the fuel injector assembly connectors.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connectors.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D14-2 - D28-85 (#10) | Always | Below 1 Ω |
| D15-2 - D28-84 (#20) | Always | Below 1 Ω |
| D16-2 - D28-83 (#30) | Always | Below 1 Ω |
| D17-2 - D28-82 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D14-2 or D28-85 (#10) - Body ground | Always | 10 Ω or higher |
| D15-2 or D28-84 (#20) - Body ground | Always | 10 Ω or higher |
| D16-2 or D28-83 (#30) - Body ground | Always | 10 Ω or higher |
| D17-2 or D28-82 (#40) - Body ground | Always | 10 Ω or higher |
| *1 | Front view of wire harness connector (to Fuel Injector Assembly) | *2 | Front view of wire harness connector (to ECM) |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D28-85 (#10) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-84 (#20) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-83 (#30) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-82 (#40) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 11.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 12.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 13.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly (Click here).
|
| ||||
| OK | |
| 14.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 15.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Data List twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 16.ADJUST VALVE TIMING |
![]() |
| *1 | Top |
| *2 | Alignment Mark |
| *3 | No. 1 Cylinder at TDC Compression |
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (P0300, P0301, P0302, P0303 OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Perform confirmation driving pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 or P0304 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling |
| MAP (Data List) | MAP value is 20 to 40 kPa (150 to 300 mmHg) (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| Outside of standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 19.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
Reinstall the EGR valve assembly (Click here).
|
| ||||
| OK | |
| 20.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTC (Click here).
Turn the power switch off and wait for 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTCs: P0300, P0301, P0302, P0303, P0304.
Check the DTCs judgment result.
| NEXT | ||
| ||
| 22.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly (Click here).
|
| ||||
| OK | |
| 24.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 25.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Data List twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 26.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling |
| MAP (Data List) | MAP value is 20 to 40 kPa (150 to 300 mmHg) (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| Outside of standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 27.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
Reinstall the EGR valve assembly (Click here).
|
| ||||
| OK | |
| 28.INSPECT SPARK PLUG |
Remove the ignition coil assembly and the spark plug of the misfiring cylinder.
Check the electrode for carbon deposits.
| Manufacturer | Product |
| DENSO | SC20HR11 |
![]() |
Measure the spark plug electrode gap.
Reinstall the ignition coil assembly and spark plug.
|
| ||||
| OK | |
| 29.CHECK FOR SPARK (SPARK TEST) |
Perform spark test .
|
| ||||
| OK | |
| 30.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 31.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D14-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| D15-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| D16-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| D17-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to Fuel Injector Assembly) |
Reconnect the fuel injector assembly connectors.
|
| ||||
| OK | |
| 32.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY- ECM) |
Disconnect the fuel injector assembly connectors.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D14-2 - D28-85 (#10) | Always | Below 1 Ω |
| D15-2 - D28-84 (#20) | Always | Below 1 Ω |
| D16-2 - D28-83 (#30) | Always | Below 1 Ω |
| D17-2 - D28-82 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D14-2 or D28-85 (#10) - Body ground | Always | 10 Ω or higher |
| D15-2 or D28-84 (#20) - Body ground | Always | 10 Ω or higher |
| D16-2 or D28-83 (#30) - Body ground | Always | 10 Ω or higher |
| D17-2 or D28-82 (#40) - Body ground | Always | 10 Ω or higher |
| *1 | Front view of wire harness connector (to Fuel Injector Assembly) | *2 | Front view of wire harness connector (to ECM) |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 33.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D28-85 (#10) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-84 (#20) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-83 (#30) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-82 (#40) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 34.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 35.ADJUST VALVE TIMING |
![]() |
| *1 | Top |
| *2 | Alignment Mark |
| *3 | No. 1 Cylinder at TDC Compression |
| NEXT | |
| 36.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Perform confirmation driving pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 or P0304 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 37.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTC (Click here).
Turn the power switch off and wait for 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTCs: P0300, P0301, P0302, P0303, P0304.
Check the DTCs judgment result.
| NEXT | ||
| ||
| 39.CHANGE TO KNOWN GOOD SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed spark plug to a known good spark plug.
Perform a spark test .
|
| ||||
| OK | ||
| ||
| 40.CHANGE TO KNOWN GOOD IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER |
Change the ignition coil assembly to a known good ignition coil assembly.
Perform a spark test .
|
| ||||
| OK | ||
| ||
| 41.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||