Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM


w/o PANEL Relay (Before October, 2010)

E187229E15


w/o PANEL Relay (From October, 2010)

E256162E01


w/ PANEL Relay (Before October, 2010)

E187228E05


w/ PANEL Relay (From October, 2010)

E256163E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except radio receiver assembly.
    B
    No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.).
    C
    Illumination comes on only for steering pad switch assembly.
    D



B
Go to step 7

C
GO TO LIGHTING SYSTEM (Click here)

D
GO TO METER / GAUGE SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)


    E126428E22
  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L52-12 (IL+2) - Body ground
    Light control switch tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.



  1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.


    E194898E01

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.

    *1
    Component without harness connected
    (Steering Pad Switch Assembly)

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG (From October, 2010)
    A
    NG (Before October, 2010)
    B
    OK
    C



B
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)

C
Go to step 5
A


4.INSPECT STEERING PAD SWITCH RH


  1. Disconnect the steering pad switch RH connectors.


    E256161E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SR1-3 (IL+2) - z9-5 (IL+2)
    Always
    Below 1 Ω
    SR1-4 (EAU) - z9-8 (EAU)
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch RH)
    -
    -



NG
REPLACE STEERING PAD SWITCH RH (Click here)
OK

REPLACE STEERING PAD SWITCH LH (Click here)  

5.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    E166173E08
  1. Disconnect the steering pad switch assembly and spiral with sensor cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-8 (EAU) - L52-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z9-5 (IL+2) - L52-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral with Sensor Cable Sub-assembly)
    *2
    Steering Pad Switch Assembly Side
    *3
    Vehicle Side



NG
REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR


    E141021E32
  1. Disconnect the radio receiver assembly and spiral with sensor cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L50-6 (SWG) - L52-4 (EAU)
    Always
    Below 1 Ω
    L50-6 (SWG) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER ASSEMBLY)


    E190646E02
  1. Disconnect the radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L34-10 (ILL+) - Body ground
    Light control switch tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT RADIO RECEIVER ASSEMBLY


    E190646E03
  1. Disconnect the radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L34-7 (GND) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)