NAVIGATION SYSTEM (for HDD) > Speaker Circuit |


| 1.CHECK HARNESS AND CONNECTOR |
![]() |
Disconnect the L120 navigation receiver assembly connector.
![]() |
Disconnect the L121 navigation receiver assembly connector.
![]() |
Disconnect the L108 stereo component amplifier assembly connector.
![]() |
Disconnect the O1 and N1 front No. 1 speaker connectors.
![]() |
Disconnect the I5 and I4 front No. 2 speaker connectors.
![]() |
Disconnect the Q3 and P3 rear speaker connectors.
![]() |
Disconnect the Q5 and P5 rear No. 2 speaker connectors.
Measure the resistance between each of the navigation receiver assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| L120-2 (FL+) - L108-1 (RL+) | Always | Below 1 Ω |
| L120-6 (FL-) - L108-6 (RL-) | Always | Below 1 Ω |
| L120-1 (FR+) - L108-2 (RR+) | Always | Below 1 Ω |
| L120-5 (FR-) - L108-7 (RR-) | Always | Below 1 Ω |
| L120-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| L120-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| L120-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| L120-6 (FL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 1 speakers and the stereo component amplifier assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| L108-4 (WFL+) - O1-1 | Always | Below 1 Ω |
| L108-11 (WFL-) - O1-2 | Always | Below 1 Ω |
| L108-3 (WFR+) - N1-1 | Always | Below 1 Ω |
| L108-8 (WFR-) - N1-2 | Always | Below 1 Ω |
| L108-4 (WFL+) - Body ground | Always | 10 kΩ or higher |
| L108-11 (WFL-) - Body ground | Always | 10 kΩ or higher |
| L108-3 (WFR+) - Body ground | Always | 10 kΩ or higher |
| L108-8 (WFR-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speakers and the navigation receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| L120-2 (FL+) - I5-1 | Always | Below 1 Ω |
| L120-6 (FL-) - I5-2 | Always | Below 1 Ω |
| L120-1 (FR+) - I4-1 | Always | Below 1 Ω |
| L120-5 (FR-) - I4-2 | Always | Below 1 Ω |
| L120-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| L120-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| L120-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| L120-5 (FR-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the rear No. 2 speakers and the navigation receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| L121-2 (RL+) - Q5-1 (+) | Always | Below 1 Ω |
| L121-6 (RL-) - Q5-2 (-) | Always | Below 1 Ω |
| L121-1 (RR+) - P5-1 (+) | Always | Below 1 Ω |
| L121-3 (RR-) - P5-2 (-) | Always | Below 1 Ω |
| L121-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| L121-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| L121-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| L121-3 (RR-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the rear No. 2 speakers and the rear speakers to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| Q5-3 (+) - Q3-1 | Always | Below 1 Ω |
| Q5-4 (-) - Q3-2 | Always | Below 1 Ω |
| P5-3 (+) - P3-1 | Always | Below 1 Ω |
| P5-4 (-) - P3-2 | Always | Below 1 Ω |
| Q5-3 (+) - Body ground | Always | 10 kΩ or higher |
| Q5-4 (-) - Body ground | Always | 10 kΩ or higher |
| P5-3 (+) - Body ground | Always | 10 kΩ or higher |
| P5-4 (-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Navigation Receiver Assembly) |
| *2 | Front view of wire harness connector (to Stereo Component Amplifier Assembly) |
| *3 | Front view of wire harness connector (to Front No. 1 Speaker) |
| *4 | Front view of wire harness connector (to Front No. 2 Speaker) |
| *5 | Front view of wire harness connector (to Rear Speaker) |
| *6 | Front view of wire harness connector (to Rear No. 2 Speaker) |
|
| ||||
| OK | |
| 2.INSPECT FRONT NO. 1 SPEAKER |
![]() |
Resistance check
Measure the resistance between the terminals of the speaker.
| Tester Connection | Condition | Specified Condition |
| O1-1 - O1-2 | Always | 1.6 to 2.4 Ω |
| N1-1 - N1-2 | Always | 1.6 to 2.4 Ω |
| *1 | Component without harness connected (Front No. 1 Speaker) |
|
| ||||
| OK | |
| 3.INSPECT FRONT NO. 2 SPEAKER |
![]() |
Resistance check
Measure the resistance between the terminals of the speaker.
| Tester Connection | Condition | Specified Condition |
| I5-1 - I5-2 | Always | 6.4 to 9.6 Ω |
| I4-1 - I4-2 | Always | 6.4 to 9.6 Ω |
| *1 | Component without harness connected (Front No. 2 Speaker) |
|
| ||||
| OK | |
| 4.INSPECT REAR SPEAKER |
![]() |
Resistance check
Measure the resistance between the terminals of the speaker.
| Tester Connection | Condition | Specified Condition |
| Q3-1 - Q3-2 | Always | 3.2 to 4.8 Ω |
| P3-1 - P3-2 | Always | 3.2 to 4.8 Ω |
| *1 | Component without harness connected (Rear Speaker) |
|
| ||||
| OK | |
| 5.INSPECT REAR NO. 2 SPEAKER |
Check that the malfunction disappears when another speaker in good condition is installed.
|
| ||||
| OK | ||
| ||