Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

for 6 Speakers:
  1. If there is a short in this circuit, the radio receiver assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.
  3. If a short is detected in the speaker circuit, no sound can be heard from the speakers.
for 8 Speakers:
  1. If there is a short in this circuit, the stereo component amplifier assembly or radio receiver assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, radio receiver assembly or speakers.
  3. If a short is detected in the speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E177570E03


E187101E02


E187102E02


INSPECTION PROCEDURE

1.CONFIRM MODEL

Result:

Result
Proceed to
for 6 Speakers
A
for 8 Speakers
B



B
Go to step 6
A


2.CHECK HARNESS AND CONNECTOR


    E189549E02
  1. Disconnect the connectors shown in the illustration from the radio receiver assembly and speakers.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *3
    Front view of wire harness connector
    (to Front No. 1 Speaker, Rear Speaker)
    *4
    Front view of wire harness connector
    (to Front No. 2 Speaker)

  1. Measure the resistance between each of the front No. 2 speakers and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L34-2 (FL+) - I3-2 (TWL+)
    Always
    Below 1 Ω
    L34-6 (FL-) - I3-4 (TWL-)
    Always
    Below 1 Ω
    L34-1 (FR+) - I2-2 (TWR+)
    Always
    Below 1 Ω
    L34-5 (FR-) - I2-4 (TWR-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speakers and front No. 2 speakers to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-1 (+) - O1-1
    Always
    Below 1 Ω
    I3-3 (-) - O1-2
    Always
    Below 1 Ω
    I2-1 (+) - N1-1
    Always
    Below 1 Ω
    I2-3 (-) - N1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speakers and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L35-2 (RL+) - Q3-1
    Always
    Below 1 Ω
    L35-6 (RL-) - Q3-2
    Always
    Below 1 Ω
    L35-1 (RR+) - P3-1
    Always
    Below 1 Ω
    L35-3 (RR-) - P3-2
    Always
    Below 1 Ω

  1. Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L34-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    L34-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    L34-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    L34-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    L35-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    L35-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    L35-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    L35-3 (RR-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speakers and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-1 (+) - Body ground
    Always
    10 kΩ or higher
    I3-3 (-) - Body ground
    Always
    10 kΩ or higher
    I2-1 (+) - Body ground
    Always
    10 kΩ or higher
    I2-3 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER


    E165683E34
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O1-1 - O1-2
      Always
      3.2 to 4.8 Ω
      N1-1 - N1-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


4.INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 5
OK

END (FRONT NO. 2 SPEAKER WAS DEFECTIVE) 

5.INSPECT REAR SPEAKER


    E165683E35
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Q3-1 - Q3-2
      Always
      3.2 to 4.8 Ω
      P3-1 - P3-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Speaker)



NG
REPLACE REAR SPEAKER (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR


    E190648E02
    E190870E01
  1. Disconnect the connectors shown in the illustration from the stereo component amplifier assembly and speakers.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *3
    Front view of wire harness connector
    (to Front No. 1 Speaker, Rear Speaker)
    *4
    Front view of wire harness connector
    (to Front No. 2 Speaker)
    *5
    Front view of wire harness connector
    (to Rear No. 2 Speaker)
    *6
    Front view of wire harness connector
    (to Stereo Component Amplifier Assembly)

  1. Measure the resistance between the radio receiver assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L108-2 (RR+) - L34-1 (FR+)
    Always
    Below 1 Ω
    L108-7 (RR-) - L34-5 (FR-)
    Always
    Below 1 Ω
    L108-1 (RL+) - L34-2 (FL+)
    Always
    Below 1 Ω
    L108-6 (RL-) - L34-6 (FL-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speakers and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L108-4 (WFL+) - O1-1
    Always
    Below 1 Ω
    L108-11 (WFL-) - O1-2
    Always
    Below 1 Ω
    L108-3 (WFR+) - N1-1
    Always
    Below 1 Ω
    L108-8 (WFR-) - N1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speakers and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L34-2 (FL+) - I5-1
    Always
    Below 1 Ω
    L34-6 (FL-) - I5-2
    Always
    Below 1 Ω
    L34-1 (FR+) - I4-1
    Always
    Below 1 Ω
    L34-5 (FR-) - I4-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speakers and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L35-2 (RL+) - Q5-1 (+)
    Always
    Below 1 Ω
    L35-6 (RL-) - Q5-2 (-)
    Always
    Below 1 Ω
    L35-1 (RR+) - P5-1 (+)
    Always
    Below 1 Ω
    L35-3 (RR-) - P5-2 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear No. 2 speakers and rear speakers to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q3-1 - Q5-3 (+)
    Always
    Below 1 Ω
    Q3-2 - Q5-4 (-)
    Always
    Below 1 Ω
    P3-1 - P5-3 (+)
    Always
    Below 1 Ω
    P3-2 - P5-4 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L34-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    L34-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    L34-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    L34-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    L35-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    L35-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    L35-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    L35-3 (RR-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L108-4 (WFL+) - Body ground
    Always
    10 kΩ or higher
    L108-11 (WFL-) - Body ground
    Always
    10 kΩ or higher
    L108-3 (WFR+) - Body ground
    Always
    10 kΩ or higher
    L108-8 (WFR-) - Body ground
    Always
    10 kΩ or higher
    L108-2 (RR+) - Body ground
    Always
    10 kΩ or higher
    L108-7 (RR-) - Body ground
    Always
    10 kΩ or higher
    L108-1 (RL+) - Body ground
    Always
    10 kΩ or higher
    L108-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the rear speakers and body ground to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q3-1 - Body ground
    Always
    10 kΩ or higher
    Q3-2 - Body ground
    Always
    10 kΩ or higher
    P3-1 - Body ground
    Always
    10 kΩ or higher
    P3-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT NO. 1 SPEAKER


    E165683E36
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O1-1 - O1-2
      Always
      1.6 to 2.4 Ω
      N1-1 - N1-2
      Always
      1.6 to 2.4 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


8.INSPECT FRONT NO. 2 SPEAKER


    B108592E16
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I5-1 - I5-2
      Always
      6.4 to 9.6 Ω
      I4-1 - I4-2
      Always
      6.4 to 9.6 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER (Click here)
OK


9.INSPECT REAR SPEAKER


    E165683E37
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Q3-1 - Q3-2
      Always
      3.2 to 4.8 Ω
      P3-1 - P3-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Speaker)



NG
REPLACE REAR SPEAKER (Click here)
OK


10.INSPECT REAR NO. 2 SPEAKER
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the rear No. 2 speakers that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (REAR NO. 2 SPEAKER WAS DEFECTIVE)